Akerstroms SESAM 800 CONFIGURABLE Manual de usuario

954446-000 EN -A1

OPERATING MANUAL

SESAM 800

L15, M6, S6, S3, K3,

RX DIN1

2 (20)

S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN

Version: A1 Author: SH

Revision history

Version Date Reason

A0 2017-05-03 1st released manual

A1 2019-08-21 Type label position added, replacing battery

claried

3 (20)

S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN

Version: A1 Author: SH

Table of Contents

1 Introduction _________________________________________ 4

2 Scope _____________________________________________ 4

3 Service _____________________________________________ 4

4 Maintenance_________________________________________ 4

5 TechnicalSpecications_______________________________ 5

6 Description of the System _____________________________ 6

6.1 Receiver _________________________________________________6

6.2 Transmitters ______________________________________________6

7 Description of the Receiver ____________________________ 7

8 Installation of the Receiver_____________________________ 7

8.1 Placement of the Receiver ___________________________________8

8.2 Connections on the Receiver _________________________________8

9 Indicators on the Receiver _____________________________ 9

10 CongurationoftheReceiver __________________________ 9

10.1 BasicConguration _________________________________________9

10.2 AdvancedConguration ____________________________________10

10.3 ErasingAllTransmittersintheReceiver ________________________10

11 Description of the Transmitters ________________________ 11

11.1 Indicators on the Transmitter_________________________________ 11

12 ReplacingBatteriesintheTransmitters _________________ 13

12.1 ReplacingBatteriesinSesamK3 _____________________________13

12.2 ReplacingBatteriesintheSesam800S3/S6 ____________________14

12.3 ReplacingBatteriesinSesam800M6 _________________________15

12.4 ReplacingBatteriesintheSesam800L15 ______________________16

13 Error Codes for Receiver _____________________________ 17

14 Measure for the Receiver _____________________________ 17

Introduction 4 (20)

S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN

Version: A1 Author: SH

1 Introduction

This manual only covers the installation of the Sesam radio remote door opening

system. The Sesam System is not a complete door opening system: it provides

only the set of outputs that are driven according to the actions performed by the

operator of the transmitter. The way the set of outputs is used for controlling the

doors depends on the specic installation and is outside the scope of the Sesam.

The complete remote control system, where the controlled object is one part, has

to be tested and approved according to the standards/norms that are applicable

and specic to the controlled object. This is not the responsibility of Åkerströms

Björbo.

2 Scope

The following guide must be used when installing Åkerströms Sesam door opening

system to ensure secure, safe operation. The installation must be carried out by

a certied electrician.

3 Service

Contact your Åkerströms Björbo AB dealer for service or support. Warranty

work must be performed by Åkerströms or authorized service center.

4 Maintenance

For cleaning use a dry cleaning cloth, if necessary use a wet cleaning cloth and a

soap solution. Never use an alcohol-based product for cleaning; it can seriously

damage the plastic.

Technical Specications 5 (20)

S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN

Version: A1 Author: SH

5 TechnicalSpecications

SystemSpecications

Operating frequency: 869,8 MHz

Channel separation: 25 kHz

Power output: < 5 mW

Functional sensitivity: <= -107 dBm BER 10-4

Transmission principle: GMSK, TDMA

Operating Temperature: -25°C - +55°C

Storage Temperature: -40°C - +85°C

SpecicationsDIN1

Power Supply 12-24 V AC/DC

Max switching capacity of relays: 2A/250VACwithcosφ=1

Fuse on current loop: 2,5AT/250 V AC (IEC 60127-2/V)

Dimensions: 92 x72,5 x 30 mm

Weight: 84g

SpecicationsK3

IP- class: IP65

Dimensions: 67x44x13 mm

Weight: 30g

Battery type: 2*CR 2025 Lithium cells

Screw Size PH00

SpecicationsS3/S6

IP- class: IP67

Dimensions: 75 x 46 x 22 mm

Weight: 80g

Battery type: 2*AAA/LR03 Alkaline

Screw Size PH00

SpecicationsM6

IP- class: IP67

Dimensions: 100 x 60 x 25 mm

Weight: 130g

Battery type: 2*AA/LR06 Alkaline

Screw Size PH2

SpecicationsL15

IP- class: IP67

Dimensions: 120x75x30

Weight: 200g

Battery type: 2*AA/LR06 Alkaline

Screw Size PH2

Table 1. TechnicalSpecications,Sesam800

Description of the System 6 (20)

S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN

Version: A1 Author: SH

6 Description of the System

6.1 Receiver

Sesam 800 RX DIN1:

• 1 Single Pole Double Throw relay.

• Memory capacity: up to 100 transmitters.

• Designed for DIN rail.

6.2 Transmitters

This document covers ve transmitter models:

Keyring K3:

• Miniature size 3 button transmitter.

• Controls up to 3 functions on 1-3 receivers.

• Suitable for short transmissions.

Small S3:

• Small size 3 button transmitter.

• Controls up to 3 functions on 1-3 receivers.

Small S6:

• Small size 6 button transmitter.

• Controls up to 6 functions on 1-6 receivers.

Medium M6: 1

• Medium size 6 button transmitter.

• Controls up to 6 functions on 1-6 receivers.

Large L15:

• Large 15 button transmitter.

• Controls up to 15 functions on 1-15 receivers.

1Type label position

Description of the Receiver 7 (20)

S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN

Version: A1 Author: SH

7 Description of the Receiver

REL1

TP0

IC3

LED6

LED7

LED5

P2 P3P1 P4 P5

ANT1

P12

12 3 4 5

1. LED indications

LED 7 Learn

LED 6 Status

LED 5 Squelch

2. External antenna

3. Learn/Erase button

4. Power connection

P1, P2

5. Connection to relay 1,

P3, P4, P5

Figure1. Sesam800RXDIN1modelconnectionsandbutton

8 Installation of the Receiver

The permanent installation of the receiver must include fuses that protect the

equipment and wiring from over current and short-circuit. In detail the power

supply of the receiver and all relay contacts must be fused.

All fuses are used as disconnecting devices. The fuses shall be easily accessible,

must submit a contact gap of at least 3.0 mm and have to be placed in the line

pole. Note that the fuse must be compatible with IEC 60127-2/V.

After the installation of the equipment, the installed cables must be bound

together in pairs (i.e. by using a cable binder) very close to the terminal blocks.

Note that there might be hazardous voltage in the receiver; therefore only certi-

ed electricians are allowed to open the lid.

Installation of the Receiver 8 (20)

S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN

Version: A1 Author: SH

8.1 Placement of the Receiver

Select a location that is within the environmental limitations of the receiver and

where it is dicult for unauthorized persons to obtain access to the receiver. If

possible, mount the receiver with the cable glands facing downwards.

SESAM RX DIN is to be mounted on a DIN rail. On

the back there is a recess that the rail ts in (see 1 in

Figure 2). When the recess is pressed against the rail the

snap t (see 2 in Figure 2) will lock the receiver to the

rail automatically. Make sure that the snap. To remove,

withdraw the snap t and lift the receiver o the rail.

Figure2. DINreceiver,thelockfortherail.

8.2 Connections on the Receiver

Power Connection Relay Connection

P1 P2 P3 P4 P5

Line (L) Neutral (N) Common terminal (C) Normally opened (NO) Normally closed (NC)

L N

P1 P2 P3 P4 P5

Figure4. Power connection and Relay connection

Indicators on the Receiver 9 (20)

S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN

Version: A1 Author: SH

9 Indicators on the Receiver

The Sesam 800 RX DIN1 model has three LED indicators that are displaying

system information.

The indications on the LEDs are as follows:

LED6

LED7

LED5

LED7 - Learn Indicates if the transmitter is in Learn Mode.

LED6 - Status Indicates that information from a transmitter

associated with the receiver has been received.

LED5 - Squelch Indicates a detected signal on the operating

frequency band.

10 CongurationoftheReceiver

10.1 BasicConguration

Note! If the receiver relay function shall be altered this has to be done before

pairing the rst transmitter, see section 10.2. By default the relay function is set

to momentary.

REL1

TP0

IC3

LED6

LED7

LED5

P2 P3P1 P4 P5

ANT1

P12

Learn/Erase button

LED7

1. Press and hold down the Learn/Erase button (≈ 1 s) on the receiver until

LED7 is ON. The Learn Mode will be active for 10 seconds (as long as

LED7 is ON).

Press the button on the transmitter that shall activate the relay, in this

receiver.

2. LED7 on the receiver ashes 3 times if the Learn procedure is successful.

Conguration of the Receiver 10 (20)

S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN

Version: A1 Author: SH

10.2 AdvancedConguration

This conguration allows the user to determine the function of the relay; mo-

mentary or remaining function. Note that this setting is possible only with the

rst transmitter, the transmitter will be learned to the receiver at the same time.

Alternative after all transmitters has been erased, see section 10.3.

Momentary function: Hold in the transmitter button in order to activate the relay.

Remainingfunction: One press on the transmitter button to activate the relay,

nextpressonthebuttonwillde-activatetherelay(on/o󰀨).

REL1

TP0

IC3

LED6

LED7

LED5

P2 P3P1 P4 P5

ANT1

P12

Learn/Erase button

LED7

LED6

1. Press and hold down the Learn/Erase button (≈ 1 s) until LED7 is ON. The

Learn Mode will be active for 10 seconds. Press the Learn/Erase button

repeatedly until LED6 is indicating the desired function.

Momentary function: LED6 (status) is OFF.

Remaining function: LED6 (status) is ON.

2. Press the button on the transmitter that shall activate the relay in this

receiver. If the conguration is accepted by the receiver, LED7 ashes 3

times. Learn procedure is successful.

10.3 ErasingAllTransmittersintheReceiver

1. Press and hold down the Learn/Erase button until LED7 is ON. The Learn

Mode will be active for 10 seconds.

2. Press and hold down the Learn/Erase button for about 5 seconds (until

LED7 is OFF). All transmitters are now erased from the receiver memory.

Otros manuales para SESAM 800 CONFIGURABLE

Tabla de contenidos

Otros manuales de Mando a distancia de Akerstroms

Akerstroms

Akerstroms SESAM 800 MOBILE TAIL LIFT Manual de usuario

Akerstroms

Akerstroms SESAM 800 CONFIGURABLE Manual de usuario

Akerstroms

Akerstroms T-Rx 1000 Manual de usuario

Akerstroms

Akerstroms SESAM 800 CONFIGURABLE Manual de usuario

Akerstroms

Akerstroms SESAM 800 CONFIGURABLE Manual de usuario

Akerstroms

Akerstroms Jupiter Era 10BD Manual de usuario

Akerstroms

Akerstroms Remotus Jupiter Manual de usuario

Akerstroms

Akerstroms SESAM 800 L15 Manual de usuario

Akerstroms

Akerstroms Remotus Jupiter Era 4 Manual de usuario

Akerstroms

Akerstroms Jupiter Era 4B Manual de usuario

Akerstroms

Akerstroms Jupiter Era 4B Manual de usuario

Akerstroms

Akerstroms SESAM 800 CONFIGURABLE Manual de usuario

Akerstroms

Akerstroms JUPITER 8B Manual de usuario

Akerstroms

Akerstroms SESAM 800 CONFIGURABLE Manual de usuario

Akerstroms

Akerstroms JUPITER 100J Manual de usuario

Akerstroms

Akerstroms SESAM 800 CONFIGURABLE Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación