AJAX MotionProtect Manual de usuario
MotionProtect / MotionProtect Plus User
Manual
Updated August 13, 2020
MotionProtect is a wireless motion detector designed for indoor use. It can
operate for up to 5 years from an in-built battery, and monitors the area within
12-meter radius. MotionProtect ignores animals, while recognizes a human from
the rst step.
MotionProtect Plus uses radio frequency scanning along with a thermal sensor,
ltering interference from thermal radiation. Can operate up to 5 years from an
in-built battery.
MotionProtect (MotionProtect Plus) operates within the Ajax security system,
connected to the via the protected protocol. The communication
range is up to 1700 (MotionProtect Plus up to 1200) meters in the line of sight.
In addition, the detector can be used as a part of third-party security central
units via the or integration modules.
Buy motion detector with microwave sensor MotionProtect Plus
hub Jeweller
Ajax uartBridge Ajax ocBridge Plus
The detector is set up via the for iOS, Android, macOS and Windows.
The system noties user of all events through push notications, SMS and calls
(if activated).
The Ajax security system is self-sustaining, but the user can connect it to the
central monitoring station of a security company.
Functional Elements
Operating Principle
Ajax app
Buy motion detector MotionProtect
1. LED indicator
2. Motion detector lens
3. SmartBracket attachment panel (perforated part is required for actuating
the tamper in case of any attempt to dismantle the detector)
4. Tamper button
5. Device switch
6. QR code
Thermal PIR sensor of MotionProtect detects intrusion into protected room by
detecting moving objects whose temperature is close to the temperature of the
human body. However, the detector can ignore domestic animals if the suitable
sensitivity has been chosen in the settings.
When the MotionProtect Plus detects motion, it will additionally carry out radio
frequency scanning of the room, preventing false actuation from thermal
interferences: air ows from sun-heated curtains and louvre shutters, operating
thermal air fans, replaces, air conditioning units, etc.
After actuation, the armed detector immediately transmits an alarm signal to the
hub, activating the sirens and notifying the user and security company.
If before arming the system, the detector has detected motion, it will not arm
immediately, but during the next inquiry by the hub.
Connecting the Detector to the Ajax Security System
Connecting the Detector to the hub
Before starting connection:
Only users with administrator rights can add the device to the hub
How to connect the detector to the hub:
1. Following the hub manual recommendations, install the .
Create an account, add the hub to the application, and create at least one
room.
Ajax application
2. Switch on the hub and check the internet connection (via Ethernet and/or
GSM network).
3. Make sure that the hub is disarmed and does not update by checking its
status in the app.
For detection and pairing to occur, the detector should be located within the
coverage of the wireless network of the hub (at a single protected object).
1. Select theAdd Deviceoption in the Ajax application.
2. Name the device, scan/write manually the QR Code (located on the body
and packaging), and select the location room.
3. Select Add — the countdown will begin.
4. Switch on the device.
Request for connection to the hub is transmitted for a short time at the moment
of switching on the device.
If the detector failed to connect to the hub, switch off the detector for 5 seconds
and retry.
The connected detector will appear in the devices list in the application. Update
of the detector statuses in the list depends on the device inquiry time set in the
hub settings(default value is 36 seconds).
Connecting the Detector to Third Party security systems
To connect the detector to a third party security central unit with the
or integration module, follow the recommendations in the
manuals of these devices.
States
Parameter Value
Temperature Temperature of the Detector. Measured on the
processor and changes gradually
Jeweller Signal Strength Signal strength between the hub and the
detector
Connection Connection status between the hub and the
detector
Battery Charge Battery level of the detector, displayed in
increments of 25%
Lid The tamper mode of the detector, which reacts
to the detachment of or damage of the body
Delay when entering, sec Delay time when entering
Delay when leaving, sec Delay time when exiting
Routed through ReX Displays the status of using the ReX range
extender
uartBridge
ocBridge Plus
1. Devices
2. MotionProtect | MotionProtect Plus
Sensitivity Sensitivity level of the motion sensor
Always Active If active, the motion detector is always in the
armed mode
Temporary Deactivation
Shows the status of the device: active,
completely disabled by the user, or only
notications about triggering of the device
tamper button are disabled
Firmware Detector rmware version
Device ID Device identier
Settings
Setting Value
First eld Detector name, can be edited
Room Selecting the virtual room to which the device is
assigned
Delay when entering, sec Selecting delay time when entering
Delay when leaving, sec Selecting delay time on exit
Delays in night mode Delay turned on when using night mode
Arm in night mode If active, the detector will switch to armed mode
when using night mode
Alarm LED indication
Allows you to disable the ashing of the LED
indicator during an alarm. Available for devices
with rmware version 5.55.0.0 or higher
Sensitivity Choosing the sensitivity level of the motion
sensor.
For MotionProtect:
1. Devices
2. MotionProtect | MotionProtect Plus
3. Settings
How to nd the rmware version or
the ID of the detector or device?
For MotionProtect Plus:
Always active If active, the detector always registers motion
Alert with a siren if motion detected If active, and are
activated when the motion detected
Jeweller Signal Strength Test Switches the detector to the signal strength test
mode
Detection Zone Test Switches the detector to the detection area test
Attenuation test
Switches the detector to the signal attenuation
test mode (available in detectors with rmware
version 3.50 and later)
Temporary Deactivation
Allows the user to disconnect the device
without removing it from the system.
Two options are available:
User Guide Opens the User Guide
High — for premises with a minimum amount of
obstacles, motion is detected as quickly as
possible
Medium — for premises with potential
obstacles (windows, air conditioner, heating
element, etc)
Low — ignore pets weighing up to 20 kg and up
to 50 cm tall
High — the detector disregards cats (under 25
cm)
Medium — disregards small dogs (under 35 cm)
Low — disregards animals under 50 cm.
HomeSiren StreetSiren
Deactivate entirely — the device will not
execute system commands or participate in
automation scenarios, and the system will
ignore device alarms and other notications
Deactivate lid notications — the system will
ignore only notications about the triggering of
the device tamper button
Learn more about temporary
deactivation of devices
Unpair device Disconnects the detector from the hub and
deletes its settings
Before using the detector as a part of the security system, set up the suitable
sensitivity level.
Switch the Always Active if the detector is located in a room requiring 24-hour
control. Regardless of whether the system is set in the armed mode, you will
receive notices of any detected motion.
If any motion is detected, the detector activates the LED for 1 second and
transmits an alarm signal to the hub and then to the user and central monitoring
station (if it is connected).
Detector operation indication
Event Indication Note
Turning on the detector Lights up green for about one
second
Detector connection to the
, and Lights up continuously for a
few seconds
Alarm / tamper activation Lights up green for about one
second
Alarm is sent once in 5
seconds
Battery needs replacing During the alarm,slowly lights
up and goes off green
Replacement of the detector
battery is described in the
manual
Detector Testing
The Ajax security system allows conducting tests for checking the functionality
of connected devices.
The tests do not start immediately but within a period of 36 seconds when using
the standard settings. The time of the start depends on the settings of the
detector polling period (the paragraph on Jeweller settings in the hub settings).
hub ocBridge Plus
uartBridge
Battery Replacement
Device installation
Selection of the Detector Location
The controlled area and the eciency of the security system depends on the
location of the detector.
The device developed only for indoor use.
Location of MotionProtect depends on the remoteness from the hub and
presence of any obstacles between the devices hindering the radio signal
transmission: walls, inserted oors, large-size objects located within the room.
Check the signal level at the installation location
Jeweller Signal Strength Test
Detection Zone Test
Attenuation test
If the signal level is at one bar, we cannot guarantee stable operation of the
security system. Take all possible measures to improve the quality of the signal!
As a minimum, move the device – even 20 cm shift can signicantly improve the
quality of reception.
If after moving the device still has a low or unstable signal strength, use the
.
The direction of the detector lens should be perpendicular to the probable way of
intrusion into the room
Make sure that any furniture, domestic plants, vases, decorative or glass
structures do not block the eld of view of the detector.
We recommend installing the detector at the height of 2,4 meters.
If the detector is not installed at the recommended height, this will reduce the
area of the motion detection zone and impair the operation of the function of
ignoring animals.
Installation of the Detector
ReX
radio signal range extender
Otros manuales para MotionProtect
10
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sensor de seguridad de AJAX
AJAX
AJAX DoorProtect Plus Manual de usuario
AJAX
AJAX MotionProtect Manual de usuario
AJAX
AJAX MotionProtect Curtain Manual de usuario
AJAX
AJAX GlassProtect Manual de usuario
AJAX
AJAX GlassProtect Manual de usuario
AJAX
AJAX DoorProtect Manual de usuario
AJAX
AJAX Fire Protect Manual de usuario
AJAX
AJAX HomeSiren Manual de usuario
AJAX
AJAX LeaksProtect Manual de usuario
AJAX
AJAX MotionProtect Manual de usuario
AJAX
AJAX FireProtect 2 (Heat) Jeweller Manual de usuario
AJAX
AJAX MotionProtect Manual de usuario
AJAX
AJAX DoorProtect Plus Jeweller Manual de usuario
AJAX
AJAX DoorProtect Plus Manual de usuario
AJAX
AJAX ReX Manual de usuario
AJAX
AJAX FireProtect 2 Manual de usuario
AJAX
AJAX CombiProtect Fibra Manual de usuario
AJAX
AJAX DoorProtect Manual de usuario
AJAX
AJAX FireProtect 2 Heat/CO Jeweller Manual de usuario
AJAX
AJAX MotionCam Jeweller Manual de usuario
