AJAX MotionProtect Manual de usuario

TH COMMUNICATION SDN BHD www.thcomm.com.my info@thcomm.com.my

MotionProtect / MotionProtect Plus User Manual

MotionProtect is a wireless motion detector designed for use inside premises. It can operate

up to 7 years from a pre-installed battery, and tracks the area with the radius of 12 meters, is

able to ignore animals, however, can recognize a man from the first step.

MotionProtect Plus together with a thermal detector uses radio frequency scanning, filtering

interferences from thermal radiation. Can operate up to 5 years from a pre-installed battery.

👉Buy motion detector with microwave sensor MotionProtect Plus

MotionProtect (MotionProtect Plus) operates within the Ajax security system, by connecting

via the protected Jeweller protocol to the Hub. The communication range is up to 1700

(MotionProtect Plus up to 1200)meters if there are no obstacles. In addition, the detector can

be used as part of third-party security central units due to the Ajax uartBridge or Ajax ocBridge

Plus integration module.

The detector is set up via a mobile application for iOS and Android-based smartphones. The

user is notified of all events through push notifications, SMS messages and calls (if activated).

The Ajax security system is self-sustaining, but the user can connect it to the central monitoring

station of a private security company.

👉Buy motion detector MotionProtect

Functional Elements

TH COMMUNICATION SDN BHD www.thcomm.com.my info@thcomm.com.my

1. LED indicator

2. Motion detector lens

3. SmartBracket attachment panel (perforated part is required for actuating the tamper in case

of any attempt to tear off the detector from the surface)

4. Tamper button

5. Device switch

6. QR code

MotionProtect Operating Principle

Thermal PIR sensor of MotionProtect detects intrusion into a protected room by detecting

moving objects whose temperature is close to the temperature of the human body. At that, the

detector can ignore domestic animals - you only need to set up the suitable sensitivity in the

settings.

When the MotionProtect Plus detects motion, it will additionally carry out radio frequency

scanning of the room, preventing false actuation from thermal interferences: air flows

from sun-heated curtains and louvre shutters, operating thermal air fans, fireplaces, air

conditioning units, etc.

After actuation, the armed immediately transmits an alarm signal to the Hub, activating the

sirens connected to the hub and notifying the user and private security company.

If before arming system the detector has detected motion, it will not set in the armed mode

immediately, but during the next inquiry by the hub.

Connecting the Detector to the Ajax security system

Before starting connection:

TH COMMUNICATION SDN BHD www.thcomm.com.my info@thcomm.com.my

1. Following the Hub instruction recommendations, install the Ajax application on your

smartphone. Create an account, add the Hub to the application, and create at least one

room.

2. Go to the Ajax application.

3. Switch on the Hub and check the internet connection (via Ethernet cable and/or GSM

network).

4. Ensure that the Hub is disarmed and does not start updates by checking its status in the

mobile application.

⚠️Only users with administrative privileges can add the device to the Hub

How to connect the detector to the Hub:

1. Select the Add Device option in the Ajax application.

2. Name the device, scan/write manually the QR Code (located on the body and packaging),

and select the location room.

Select Add —the countdown will begin.

TH COMMUNICATION SDN BHD www.thcomm.com.my info@thcomm.com.my

3. Switch on the device.

For the detection and interfacing to occur, the detector should be located within the

coverage area of the wireless network of the hub (at a single protected object).

Request for connection to the hub is transmitted for a short time at the time of switching on

the device.

If the connection to the Ajax Hub failed, switch off the detector for 5 seconds and repeat the

attempt.

The detector connected to the hub will appear in the list of devices of the hub in the

application. Update of the detector statuses in the list depends on the device inquiry time set

in the hub settings, with the default value - 36 seconds.

Connecting the Detector to Third Party security systems

To connect the detector to a third party security central unit using the Ajax uartBridge or Ajax

ocBridge Plus integration module, follow the recommendations in the manual of the respective

device.

States

Devices → MotionProtect (MotionProtect Plus)

TH COMMUNICATION SDN BHD www.thcomm.com.my info@thcomm.com.my

Parameter

Value

Temperature

Temperature of the Detector. Measured on the

processor and changes gradually

Signal Strength

Signal strength between the Hub and the

detector

Battery Charge

Battery level of the detector, displayed in

increments of 25%

Lid

The tamper mode of the detector, which reacts

to the detachment of or damage to the body

Delay when entering, sec

Delay time when entering

Delay when leaving, sec

Delay time when exiting

Connection

Connection status between the Hub and the

detector

TH COMMUNICATION SDN BHD www.thcomm.com.my info@thcomm.com.my

Sensitivity

Sensitivity level of the motion sensor

Always Active

If active, the motion detector is always in the

armed mode

Firmware

Detector firmware version

Device ID

Device identifier

Settings

Devices → MotionProtect (MotionProtect Plus) → ⚙️

Setting

Value

First field

Detector name, can be edited

Room

Selecting the virtual room to which the device is assigned

TH COMMUNICATION SDN BHD www.thcomm.com.my info@thcomm.com.my

Sensitivity

Choosing the sensitivity level of the motion sensor:

For Motion Protect:

High - for premises with a minimum amount of obstacles,

motion is detected as quickly as possible

Normal - for premises with potential obstacles (windows, air

conditioner, heating element, etc)

Low - ignore pets weighing up to 20 kg and up to 50 cm tall

For MotionProtect Plus:

High: The detector disregards cats (under 25 cm).

Medium: Disregards small dogs (under 35 cm).

Low: Disregards animals under 50 cm.

Always active

If active, the detector always registers motion

Delay when entering, sec

Selecting delay time when entering

Delay when leaving, sec

Selecting delay time on exit

Delays in night mode

Delay turned on when using night mode

Arm in night mode

If active, the detector will switch to armed mode when using

night mode

Alert with a siren if motion

detected

If active, HomeSiren and StreetSiren are activated when the

motion detected

Signal Strength Test

Switches the detector to the signal strength test mode

Detection Zone Test

Switches the detector to the detection area test

Attenuation test

Switches the detector to the signal fade test mode (available in

detectors with firmware version 3.50 and later)

User Guide

Opens the detector User Guide

Unpair device

Disconnects the detector from the hub and deletes its settings

Before using the detector as a security system element, set up the suitable sensitivity level of

the sensor.

The "Always Active" mode is worth switching on if the detector is located in a room requiring

24-hour control. Regardless of whether the system is set in the armed mode, you will receive

notices of any detected motion.

TH COMMUNICATION SDN BHD www.thcomm.com.my info@thcomm.com.my

If any motion is detected, the detector activates the LED for 1 second and transmits an alarm

signal to the hub and then to the user and central monitoring station (if it is connected).

Detector operation indication

Event

Indication

Note

Turning on the

detector

Lights up green for about one

second

Detector

connection to the

Hub, ocBridge,

and uartBridge

Lights up continuously for a

few seconds

Alarm / tamper

activation

Lights up green for about one

second

Alarm is sent once in 5 seconds

Battery needs

replacing

During the alarm, it slowly

lights up green and slowly

goes out

Replacement of the detector battery is

described in the Battery

Replacementparagraph

Detector Testing

The Ajax security system allows conducting tests for checking the functionality of connected

devices.

The tests do not start straight away but within a period of 36 seconds when using the standard

settings. The test time start depends on the settings of the detector scanning period (the

paragraph on “Jeweller” settings in Hub settings).

Signal Strength Test

Detection Zone Test

Attenuation test

Selection of the Detector Location

The area of the controlled territory and, consequently, the efficiency of the security system

depends on the location of the detector.

Location of the Ajax MotionProtect detector determines its remoteness from the hub and

presence of any obstacles between the devices hindering the radio signal transmission: walls,

inserted floors, large-size objects located within the room.

⚠️Check the signal level at the installation location

If the signal level is one division, we cannot guarantee stable operation of the security system.

Take possible measures to improve the quality of the signal! As a minimum, move the device -

even 20 cm shift can significantly improve the quality of reception.

TH COMMUNICATION SDN BHD www.thcomm.com.my info@thcomm.com.my

If, after moving, the device still has a low or unstable signal strength, use a radio signal range

extender ReX.

It is advisable that the direction of the detector lens sight is perpendicular to the probable way of

intrusion into the room.

Make sure that any furniture, domestic plants, vases, decorative or glass structures do not block

the field of view of the detector.

We recommend installing the detector at the height of 2.4 meters.

TH COMMUNICATION SDN BHD www.thcomm.com.my info@thcomm.com.my

If the detector is not installed at the recommended height, this will reduce the area of the motion

detection zone and impair the operation of the function of ignoring animals.

Installation of the Detector

Before installing the detector, make sure that you have selected the optimal location and it is in

compliance with the guidelines contained in this manual!

Otros manuales para MotionProtect

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sensor de seguridad de AJAX

AJAX

AJAX FireProtect Manual de usuario

AJAX

AJAX FireProtect 2 Jeweller Manual de usuario

AJAX

AJAX FireProtect 2 Jeweller Manual de usuario

AJAX

AJAX CombiProtect Manual de usuario

AJAX

AJAX FireProtect 2 Jeweller Manual de usuario

AJAX

AJAX DoorProtect Manual de usuario

AJAX

AJAX DualCurtain Outdoor Manual de usuario

AJAX

AJAX GlassProtect Fibra Manual de usuario

AJAX

AJAX GlassProtect Manual de usuario

AJAX

AJAX FireProtect 2 Jeweller Manual de usuario

AJAX

AJAX GlassProtect Manual de usuario

AJAX

AJAX MotionProtect Manual de usuario

AJAX

AJAX GlassProtect Manual de usuario

AJAX

AJAX DoorProtect Manual de usuario

AJAX

AJAX FireProtect Manual de usuario

AJAX

AJAX ReX Manual de usuario

AJAX

AJAX HomeSiren Manual de usuario

AJAX

AJAX CombiProtect Manual de usuario

AJAX

AJAX GlassProtect Manual de usuario

AJAX

AJAX LeaksProtect Manual de usuario

AJAX

AJAX GlassProtect Manual de usuario

AJAX

AJAX MotionCam Jeweller Manual de usuario

AJAX

AJAX GlassProtect Manual de usuario

AJAX

AJAX DoorProtect Plus Manual de usuario

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario