airnet AIR-BR1000AGN Manual de usuario
Quick Installaon Guide
Package Contents:
Airnet Outdoor Access Point
Mounng Bracket (Include: 2 Mounng
Brackets and 4 screw nuts)
PoE Injector
Power Cable
RJ45 Waterproof Connector System
CD-ROM
300 Mbps GIGA1000 SERIES
AIRNET GIGA MIMO 300 Mbps AP/Bridge Single Radio Series
AIR-BR1000AGN - AIR-BR1000GNH - AIR-BR1000ANH
Warnings
Hardware
Installaon
1
Quick
Installaon
Guide
Do not work on the system or connect or disconnect cables during periods of lightning acvity.
NETKROM shall not be liable for incidental or consequenal damages resulng from the furnishing, performance, or use of
this manual.
Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into
contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, as they
may cause serious injury or death.
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
To meet regulatory restricons, the radio and the external antenna must be professionally installed. The network
administrator or other IT professional responsible for installing and configuring the unit must be a suitable professional
installer. Following installaon, access to the unit should be password protected by the network administrator to maintain
regulatory compliance.
The Airnet outdoor access point and PoE injector can be damaged by incorrect power applicaon. Read and carefully follow
the installaon instrucons before connecng the system to its power source.
2
High Capacity Wireless Networks www.netkrom.com
300 Mbps GIGA1000 SERIES
Package contents
Hardware
Installaon
1
Quick
Installaon
Guide
Take a moment to ensure you have all of the following parts in your Outdoor Waterproof Unit installaon kit before you begin
installing the product. If any parts are missing, please contact your local vendor or contact us, please see the contact
informaon in Secon 6.
3
www.netkrom.comHigh Capacity Wireless Networks
300 Mbps GIGA1000 SERIES
Setup Requirements
Before starng, please verify that the following is available:
Hardware
Installaon
1
Quick
Installaon
Guide
CAT5/5e or FTP Outdoor Ethernet cable (from the Outdoor AP to PoE Injector)
At least one computer is installed with a Web browser and a wired or wireless
network interface adapter
TCP/IP protocol is installed and IP address parameters are properly configured
on all your network’s nodes
4
www.netkrom.com
Important!
Configure and verify the outdoor access point operaons first before you
mount the unit in a remote locaon.
You may need to install a lightning arrestor to protect your outdoor access
point from lightning.
For choosing the best locaon for your outdoor access point choose an
elevated locaon where trees, buildings and large steel structures will not
obstruct the antenna signals and which offers maximum line-of-sight
propagaon with the users.
Select an appropriate antenna to improve range and/or coverage. The access
point also lets you fine-tune parameters such as the transmit power to achieve
the best results.
High Capacity Wireless Networks
300 Mbps GIGA1000 SERIES
Outdoor AP Installaon
Step 1:
Hardware
Installaon
1
Quick
Installaon
Guide
Connect one end of your UTP or FTP Outdoor cat.5 Ethernet cable
with waterproof connector to the RJ-45 connector located in the
Outdoor Access Point. Then connect the other end of the cable to
the PoE injector.
For the Netkrom PoE, the recommended length of the Category 5
cable is up to 260 feet or 80 meters.
1. Remove the thin enclosure nut from the feedthru assembly.
This can be discarded. Loosen the compression nut completely.
5
www.netkrom.com
2. Insert the RJ45 connector thru the feedthru assembly.
3. Tighten the compression nut loosely to the feedthru assembly.
enclosure nut
feedthru
assembly
compression nut
High Capacity Wireless Networks
300 Mbps GIGA1000 SERIES
Hardware
Installaon
1
Quick
Installaon
Guide
6
www.netkrom.com
4. Screw the enre feedthru assembly into the RJ45- ECS housing
which is already mounted in the enclosure. There should be a
rubber gasket between the two assemblies. Tighten the
feedthru assembly to create a seal.
5. The final step is to ghten the compression nut unl the gaskets
are ght around the Cat5 cable. Always push the cable toward
the connector while ghtening to ensure good strain relief of
cable to connector.
Step 2:
Connect the external antenna to the N Female connector of the
Access Point.
Screw in the Coaxial cable connector correctly into the antenna
connector (N-Female) located on the Outdoor Access Point case.
Make sure the former line is properly done and cover the N
connectors with an insulang tape.
RJ-45 ECS Housing
High Capacity Wireless Networks
300 Mbps GIGA1000 SERIES
Hardware
Installaon
1
Quick
Installaon
Guide
7
www.netkrom.com
From the PoE injector connect one cat.5 Ethernet cable
to the radio and another cat.5 cable to a switch or PC.
Connect the power cable supplied in the Netkrom PoE kit
to the main electrical supply and the power plug into the
socket of the injector. Now, turn on your power supply.
Noce that the POWER LED has lighted up. This indicates
that the access point is receiving power through the
Netkrom PoE Injector and that connecon between your
access point and your network has been established.
Note Please use the PoE injector provided in the package.
Using a PoE with a different voltage rang will damage
this product.
Step 3:
Poe Injector
Poe Injector
To Antena
To Antena
To Switch or Pc
To Switch or Pc
Power Cable
High Capacity Wireless Networks
300 Mbps GIGA1000 SERIES
8
www.netkrom.com
Mounng Outdoor AP
Outdoor Access Point device can be mounted on the pole or tower as
shown in following:
1. Mount the bracket to the pole.
2. Aach the radio to the bracket which was mounted on the pole
with the supplied nuts and 4 screws.
Hardware
Installaon
1
Quick
Installaon
Guide
High Capacity Wireless Networks
300 Mbps GIGA1000 SERIES
9
www.netkrom.com
uConfig
Ulity2
Quick
Installaon
Guide
Using uConfig
When you execute the uConfig file you should see a window as it is
shown on the right side. Click yes to connue
The screen is divided into three secons. The top secon shows the
Ethernet adapter that is accessing the network device and the middle
poron shows the roung table associated with the Ethernet adapter.
In the lower window, a list of all uConfig compable devices on the
network is shown.
Highlight the device you desire to configure. Then click on the “Open
web” buon.
uConfig is a feature that provides the ability to directly access the
AIRNET AP/BR 600 without the need to know absolutely its IP
address. It may be run directly from the product CD or installed on
the user’s PC for later access.
High Capacity Wireless Networks
300 Mbps GIGA1000 SERIES
10
www.netkrom.com
Click the OK buon to connue
At the login prompt, enter the User name and Password.
The default are:
User name: admin
Password: password
Click on OK and start configuring the radio.
uConfig
Ulity2
Quick
Installaon
Guide
High Capacity Wireless Networks
300 Mbps GIGA1000 SERIES
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de airnet
