AirLive WT-2000 ARM Manual de usuario
AirLive WT-2000ARM ADSL2/2+ Router 1
WT-2000 ARM
Wireless ADSL 2/2+ Modem Router
User’s Guide
AirLive WT-2000ARM ADSL2/2+ Router 2
Copyright
The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an
information retrieval system, translated into any language, or transmitted in any form or by any means,
mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written
permission.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against radio interference in a
residential environment. AirLive WT-2000 ARM can generate, use and radiate radio frequency energy and, if
not installed and used in accordance with the instructions in this manual, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If AirLive WT-2000
ARM does cause harmful interference to radio or television reception, which is found by turning the equipment
ON and OFF, the user is encouraged to try to reduce the interference by one or more of the following measures:
yAdjust or relocate the receiving antenna
yIncrease the separation between the equipment or device
yConsult a dealer or an experienced technician for assistance
CE Declaration of Conformity
This is to certify that this device complies the essential protection requirements of the European Council
Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class B (CISPR 22).
Compliance with the applicable regulations is dependent upon the use of shielded cables. It is the responsibility
of the user to procure the appropriate cables.
AirLive WT-2000ARM ADSL2/2+ Router 3
Contents
1. INTRODUCTION ...................................................1
1.1. FEATURES....................................................................2
1.2. MINIMUM REQUIREMENTS .............................................3
1.3. PACKAGE CONTENT......................................................3
1.4. HARDWARE PLACEMENT ...............................................4
1.4.1. Rear Panel ....................................................................... 4
1.4.2. Front LEDs ....................................................................... 5
2. HARDWARE INSTALLATION ..............................6
3. SETUP WIZARD....................................................7
4. IP ADDRESS SETTING ......................................13
5. WEB MANAGEMENT CONFIGURATION..........21
5.1. QUICK START .............................................................24
5.2. INTERFACE SETUP ......................................................29
5.2.1. Internet ........................................................................... 29
5.2.2. LAN ................................................................................ 34
5.2.3. Wireless.......................................................................... 37
5.3. ADVANCED SETUP ......................................................41
5.3.1. Firewall........................................................................... 41
5.3.2. Routing........................................................................... 42
5.3.3. NAT ................................................................................ 46
5.3.3.1. NAT........................................................................................ 46
5.3.3.2. DMZ ....................................................................................... 47
5.3.3.3. Virtual Server ......................................................................... 48
5.3.4. ADSL .............................................................................. 50
5.4. ACCESS MANAGEMENT ...............................................51
5.4.1. ACL ................................................................................ 51
5.4.2. IP Filter ........................................................................... 52
5.4.3. SNMP ............................................................................. 55
5.4.4. UPnP.............................................................................. 56
5.4.5. DDNS ............................................................................. 57
AirLive WT-2000ARM ADSL2/2+ Router 4
5.5. MAINTENANCE ............................................................59
5.5.1. Administrator .................................................................. 59
5.5.2. Time Zone ...................................................................... 60
5.5.3. Firmware ........................................................................ 61
5.5.4. System Restart............................................................... 62
5.5.5. Diagnostics..................................................................... 63
5.6. STATUS......................................................................64
5.6.1. Device Info ..................................................................... 64
5.6.2. System Log .................................................................... 65
5.6.3. Statistics ......................................................................... 66
6. TROUBLESHOOTING ........................................67
7. GLOSSARY.........................................................71
1
1. Introduction
Congratulations on purchasing this 802.11g Wireless LAN ADSL2+ Router. This
router is a cost-effective ADSL2+ router, with the combination of an ADSL2+
modem, router, Ethernet network switch and wireless access point, you can surf
the Internet through your ADSL2/2+ broadband connection without investing
other devices.
This router can support downstream transmission rates of up to 24Mbps and
upstream transmission rates of up to 1Mbps. It supports PPPoA (RFC 2364 -
PPP over ATM Adaptation Layer 5), RFC 1483/2684 encapsulation over ATM
(bridged or routed) and PPP over Ethernet (RFC 2516) to establish a connection
with ISP. The product also supports VC-based and LLC-based multiplexing.
With the web management interface, users can easily configure the various
functions of the router including DHCP server, NAT, virtual server, DMZ, access
control, IP filter, Firewall, PPTP/IPSec/L2TP pass-through, DDNS, UPnP,
Wireless and etc.
This router is a high performance and high-speed device that provides a full rate
of ADSL2+ standard with the superb reliability and a complete solution for home
and office application.
2
1.1. Features
ADSL2/2+ Compliance
•Support downstream rates of up to 24Mbps and upstream rates of up to
1Mbps.
•Compliant to ITU-T G.992.1 (G.dmt), G.992.2 (G.lite), G.992.3 (ADSL2),
G.992.4 (splitterless ADSL2), G.992.5 (ADSL2+) for Annex A, B. (Annex A
and B are supported in different H/W platform)
•Supports Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (G.992.1);
G.994.1 and G.996.1 (for ISDN only); G.991.1;G.lite (G992.2)).
•Multiple Protocols over AAL5 (RFC 1483/2684).
•PPP over AAL5 (RFC 2364).
•PPP over Ethernet (RFC 2516).
Support 802.11g Wireless Access Point
•Complies with IEEE 802.11g/b standard.
•High data rate – up to 54Mbps network speed.
•Supports 64-bit/128-bit WEP, WPA-PSK and WPA2-PSK wireless security
functions.
•Supports MAC address filtering.
Router
•NAT (Network Address Translation) IP Sharing
•Virtual Server
•DMZ
•VPN Pass Through (IPSec/PPTP/L2TP)
•SPI Anti-DOS Firewall
•DHCP Server and Client
Access Management
•ACL (Access Control)
•IP Filter
•UPnP (Universal Plug and Play)
•SNMP
•Dynamic DNS
3
1.2. Minimum Requirements
The following devices are necessary to configure and use the ADSL2+ Router:
•A PC with Pre-installed Ethernet Adapter (Required) and a Web-Browser
(Internet Explorer 4.0 or higher)
•RJ-45 Ethernet crossover cable (Included in the package)
•RJ-11 (ADSL Ready) phone Line
1.3. Package Content
•One ADSL2+ Router (Annex A or B)
•One Dipole Antenna
•One Power Adapter (12VDC, 1A)
•One RJ-45 Ethernet Cable (100 cm)
•One RJ-11 Telephone Line (180 cm)
•One Quick Installation Guide
•One CD with full User Manual
4
1.4. Hardware Placement
1.4.1. Rear Panel
1) Antenna Connector
The antenna connector of the router is reverse SMA connector. It allows you
to connecting an external antenna with reverse SMA connector to the router
easily.
2) Reset
The Reset button can be used to reset the router or restore to factory defaults.
zIf problems occur with your router, press the router’s reset button with a
pencil tip (for less than 5 seconds) and the router will re-boot itself,
keeping your original configurations.
zIf problems persist or you experience extreme problems or you forgot
your password, press the reset button for longer than 5 seconds and the
router will reset itself to the factory default settings (warning: your
original configurations will be replaced with the factory default settings)
3) Power Jack
Please plug the power adapter attached with the ADSL Router to the power
jack. The power adapter is 12VDC, 1A.
4) Local Area Network (LAN)
5
The router’s 4 LAN ports are where you connect your LAN’s PCs, printer
servers, hubs and switches etc.
5) ADSL
Connect the supplied RJ-11 telephone line to this port and your
ADSL/telephone network.
1.4.2. Front LEDs
On the router’s front panel there are LED lights that inform you of the router’s
current status. Below is an explanation of each LED and its description.
LED Light Status Description
On The router is readyPWR (Green)
Off Wireless LAN is disabled
Blinking Wireless traffic is transmitting or receiving
WLAN (Yellow)
On Connected to an ADSL DSLAN
successfully
ADSL (Green)
Blinking No connection
On The LAN cable is connected to the router
Off No network connection.
LAN LNK/ACT (Port 1-4)
Blinking Network traffic transferring or receiving
through the LAN port
6
2. Hardware Installation
Step 1. Connect the ADSL Line
Connect the router to your ADSL cable through the supplied RJ-11 telephone line.
Step 2. Connect the router to your LAN network
Connect the router to your PC, hub or switch by attached the Ethernet cable to
the LAN port of the router.
Step 3. Connect the Power Adapter to the Router
Connect the power adapter to the power jack on the rear panel of router.
Step4: Check the ADSL LED on the Router
The ADSL LED will be ON if the router is connected to the ADSL cable and
receives the ADSL signals successfully. If the LED is blinking, please contact
with your ISP (Internet Service Provider) to check the problem.
Note: You must use the power adapter shipped along with the router, do
NOT use any other power adapter from other sources.
Tabla de contenidos
Otros manuales de Enrutador de red de AirLive
AirLive
AirLive DS-100 v2 Manual de usuario
AirLive
AirLive ARM-204 Manual de usuario
AirLive
AirLive WL-8000VPN Manual de usuario
AirLive
AirLive N450R Manual de usuario
AirLive
AirLive DS-100 v2 Manual de usuario
AirLive
AirLive N450R Manual de usuario
AirLive
AirLive WL-5470POE Manual de usuario
AirLive
AirLive TRAVELER3GM Manual de usuario
AirLive
AirLive IP-2000VPN Manual de usuario
AirLive
AirLive Ether-FSH24 Manual de usuario
AirLive
AirLive DS-100 Manual de usuario
AirLive
AirLive Ether-GSH8TW v2 Manual de usuario
AirLive
AirLive WN-300R Manual de usuario
AirLive
AirLive AC-1200R Manual de usuario
AirLive
AirLive AC-1200UR Manual de usuario
AirLive
AirLive ARM-201E Manual de usuario
AirLive
AirLive A.DUO Manual de usuario
AirLive
AirLive Ether-FSH2400N Manual de usuario
AirLive
AirLive A.DUO Manual de usuario
AirLive
AirLive IP-1000R Instrucciones de funcionamiento
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad