Airlink101 APSUSB211 Manual de usuario
Quick Installation Guide
Model #APSUSB211
Ver. 1B
1-Port USB 2.0 Print Server
Step 1ConnectoneendoftheEthernetcabletotheRJ-45 port of the PrintServerandattach the other
endof the cable to a router.
Step 2 Makesure the printer is powered OFF, then connect one end of the USB cable to the USB port of
thePrint Server and attachthe other endofthe cable to the USB portoftheprinter.
Step 3Power ON the printer.
Step 4 Plugone end of the power cord intothePrintServer and the other end into an electricaloutlet.
Connecting the Print Server
Section 1
Note: Beforeproceeding with the steps below,pleaseverifythattheprinter operates properly on each of
thecomputer thatwill beprintingthrough thePrint Server.
Warning: OnlyaUSB printer may be connected totheUSB port of the Print Server.Connecting any
otherUSB device to the Print Server may damage the Print Server.Do not plug the power cord to the
PrintServer until you havereached Step 4 ofthissection.
Section 2
Installing PS Utility
Step 1Insertthe provided CD and wait fortheautorunscreen to appear.
Step 2 Click on Install PS Utility.
Step 3 Click Next.
Note: Ifthe autorunscreen doesnot appearautomatically,goto Start,Run, type D:\autorun.exe
(whereD istheletterofyourCDdrive)andclick OK.
Step 4 Click Next.
Step 5 Click Yes.
Step 6 Click Finish.
Section 3
Configuring Network Setting
Before configuring the Print Server’s network setting, please take note of your computer’s
TCP/IP setting.
Step 1 Click on Start, Run, and type command (for Windows 95/98/ME) or cmd (for Windows 2000/
XP) and click OK.
Step 2 At the command prompt, type ipconfig and press Enter.
Step 3 WritedowntheinformationfortheIPAddress,Subnet Mask,and Default Gateway.Youwill
needthese informationlater.
Step 4Run the PS Utility by going to Start, (All) Programs,PS-Utility, PS-Utility v3.00.
Step 5 Make sure the Print Server is listed under the Device Name and click on Change IPAddress.
Step 6 Inthe IPAddress field, enter a valid IPaddress, subnetmask,and default gateway that matches
yourlocalareanetwork.
For example:Ifyourcomputer’sIPAddress is192.168.1.100, enter the same three numbers:
192.168.1 inthe corresponding fields.
Note: You can leave thelast IPAddress number 254 asis unless another networkdevice
(i.e.the Default Gateway) isalready usingthat number. If another networkdevice is alreadyusing 254,
then changeit to anothernumber that is currentlynot in use(preferably 200 - 253).
Step 8 Click OK.
Step 9 Close the PS Utility program.
Step 7 For the Subnet Mask andDefault Gateway fields, enter the same number as the TCP/IP setting
ofyourcomputer.
Verifying Network Connection
Section 4
Step 1Run the PS Utility by going to Start, (All) Programs,PS-Utility, PS-Utility v3.00.
Step 2 Make sure the Print Server is detected under the Device Name.
Step 3 Click on Show Web Setup to display the Print Server’s Web Configuration Utility.
Step 4 Click on the Printer Information link and make sure the Printer Status displays On line.
Step 5 Clickon thePrint Test link and click the Test button.The Print Server will perform a low-level
printtest, bypassingthe operatingsystemlayer.
Note:Your printer should print outatest page.If not, verify that theprinterispowered on and all cables
aresecurely connected and try again.Iftheprinter still fails to printatestpage, please check the printer
compatibilitylistonourweb site at www.airlink101.com for a list of compatibleprinters.Ifyourprinter is
noton the list, it maynotbe compatiblewith the Print Server.
Step 6 Oncethe printer successfully prints out atestpage, you may close the webbrowserandproceed
tothenextsection.
Section 5
Running PS Wizard
Warning: Make sure youhaveinstalledtheprinter driver locally oneverycomputer that will usethe
PrintServer inyournetwork before runningthePS Wizard.Otherwise, thePSWizardwillnot run properly.
Besure to runthePS Wizard onallthe computers that willusethe Print Serverinyour network.
Step 1Insert the provided CD and wait for the autorunscreentoappear.
Step 2 Click on Run PS Wizard.
Note: Ifthe autorunscreen doesnot appearautomatically, goto Start,Run, type D:\autorun.exe
(whereD istheletterofyourCDdrive)andclick OK.
Section 4
Step 3 Click Next.
Step 4 Select the printer that is connected to the print server and clickNext.
Otros manuales para APSUSB211
2
Tabla de contenidos
Otros manuales de Servidor de impresión de Airlink101
Airlink101
Airlink101 APSUSB2 Manual de usuario
Airlink101
Airlink101 APSUSB201 Manual de usuario
Airlink101
Airlink101 APSUSB203 Manual de usuario
Airlink101
Airlink101 APSUSB2 Manual de usuario
Airlink101
Airlink101 AMPS230 Manual de usuario
Airlink101
Airlink101 APSUSB201W Manual de usuario
Airlink101
Airlink101 APSMFP210 Manual de usuario
Airlink101
Airlink101 APSUSB1 Manual de usuario
Airlink101
Airlink101 AMPS240W Manual de usuario
Airlink101
Airlink101 APSMFP210 Manual de usuario
Airlink101
Airlink101 APSUSB203 Manual de usuario
Airlink101
Airlink101 APSUSB1 Manual de usuario
Airlink101
Airlink101 APSUSB201W Manual de usuario
Airlink101
Airlink101 AMPS230 Manual de usuario
Airlink101
Airlink101 APSUSB211 Manual de usuario
Airlink101
Airlink101 APSUSB201 Manual de usuario
Airlink101
Airlink101 AMPS240W Manual de usuario
