AIRINNOVATIONS MH-701 Manual de instrucciones
CLEAN MIST
DIGITAL HUMIDIFIER
TABLETOP &
FLOOR STANDING
Instruction Manual and
Warranty Information
IM0018A READ AND SAVE THESE INSTRUCTIONS
nished size 5.5” wide x 8.5” high
Contents
Safety Instructions ............................................................................................................. 1
Unpacking / Specications ............................................................................................... 2
Parts & Contents ............................................................................................................... 3
Filling The Water Tank ....................................................................................................... 4
Operating Instructions ....................................................................................................... 5
Weekly Cleaning & Care / Storage .................................................................................... 6
Troubleshooting ................................................................................................................. 7
Other Great Products ........................................................................................................ 8
Warranty ............................................................................................................................ 9
SAFETY INSTRUCTIONS
• Prior to using the appliance, read through the instructions for complete use
and keep in a safe place for later reference.
• WARNING – DO NOT use outdoors. Only use as intended and described in
this manual.
• DO NOT expose or immerse the Base in water or other liquids.
• Before using the appliance, extend the cord and inspect for any signs of
damage. DO NOT use if cord has been damaged.
• Keep cord away from heated surfaces and out of the way, where it cannot
be stepped on or tripped over.
• This appliance has a polarized plug (one blade is wider than the other) as a
safety feature. If the plug does not t fully into the outlet, reverse the plug. If
it still doesn’t t, contact a qualied electrician. DO NOT attempt to defeat this
safety feature.
• Always place humidier on an elevated rm, at, level surface; where it’s not
easily knocked over. e.g. on a table, chest, cabinet, etc.
• DO NOT place the appliance next to a heating vent, under direct sunlight,
high temperature areas, near computers or sensitive electronic equipment.
• DO NOT place the appliance directly on wood furniture or other surfaces
which could get damaged by water. e.g. waterproof surface or mat.
• NEVER use in an environment where explosive gases are present.
• DO NOT use any attachments not provided with the unit.
• NEVER use the appliance after a malfunction, after it has been dropped or
damaged in any other way.
• Only operate when fully assembled.
• Keep out of reach of children. Close supervision is necessary when this
appliance is used by or near children, elderly or disabled persons.
• NEVER drop or insert any object into any opening.
• DO NOT block any air outlets or intakes.
• NEVER cover the appliance when it’s in operation.
• To unplug turn controls to the “OFF” position, then remove the plug from the outlet.
Ensure your hands are dry.
• ALWAYS unplug and empty the water tank when not in use for a long period of time.
• ALWAYS unplug before removing, lling or emptying the water tank.
• DO NOT wash, adjust or move without rst unplugging the unit.
• DO NOT move appliance with water inside the tank. In this case remove the water
tank prior of moving.
• DO NOT touch the water or any other part in the base during operation.
• NEVER operate without water in the tank.
• DO NOT use hot water in the tank.
• ONLY use water in the tank, never add any additive such as essential oils,
eucalyptus, water conditioners, etc… to the water.
• Please hold the water tank rmly with both hands when carrying full tank of water.
• DO NOT attempt to repair or adjust the unit. Servicing must be performed by
professional or qualied personnel.
• Discontinue use if unit makes loud noises or has a strange smell.
• Perform regular maintenance of the Ultrasonic Nebulizer.
• DO NOT direct the mist against a wall or other home appliance.
1
No More Dry Air
Thank you for choosing the Air Innovations® – Clean Mist Tabletop & Floor Standing Digi-
tal Humidier and congratulations on taking this important step in improving the quality of
air in your home or ofce.
The Air Innovations® – Clean Mist Humidier uses Ultrasonic Technology to create humid-
ity instantaneously, while working silently to erase the discomforts of dry air.
Unpacking
Specications
Remove the Dual Direction Mist
Nozzle and Extension Nozzle
from the top of the packaging.
Remove the plastic bag
from the humidier.
Remove the lter from box
and remove bag.
Carefully remove the humidier from
the box by pulling the base of the
unit(Do not take the unit out of the
box by pulling the tank).
Product Model Power Consumption Rating Voltage Tank Capacity Dimensions Weight
MH-701 30W 120V 6.5L / 1.7 Gallon L8.19” X W8.19”
X H18.5”
3.4 Lbs.
1 2
3 4
*Follow directions to ll and operate the humidier.
2
1. Dual Directional Mist Nozzle
2. Extension Nozzle
3. Handle
4. Tank
5. Base
6. Control Panel
7. Air Outlet
8. Water Sensor
9. Ultrasonic Nebulizer
10. Water Reservoir
11. Cleaning Brush
12. Ceramic Filter
13. Tank Cap
14. Bottom Tank Handle
3
Parts & Contents
2
4
3
5
6
7
8
9
10
11
12
13
14
1
Filling The Water Tank
CAUTION: Always unplug the unit before removing the Water Tank. Do not touch the water in the base.
Remove Extension Nozzle and
Dual Directional Mist Nozzle
prior to lling the water tank.
Attach Ceramic/Demin-
eralization lter (included)
to the Tank Cap by
aligning the lock tabs on
both and turning the cap
counterclockwise to lock.
When attached properly
the Filter will not fall from
the Tank Cap.
Replace the Tank Cap by
rmly turning clockwise until
tight. Turn the Water Tank
upright and check the Tank
Cap for leaks. If any water
drips, remove the Tank
Cap and retighten. Do not
place Water Tank on the
Humidier Base if the cap
is leaking.
Lift the handle up and replace
on the Humidier Base, make
sure to follow the shape of the
Water Tank and the Humidier
Base (as shown to the left) so
that the tank sits level and ush
to the base. Ensure the tank is
rmly seated.
Attach the Dual Directional
Mist Nozzle or Extension
Nozzle & Dual Directional Mist
Nozzle together to the top of
the Humidier Tank for desired
use as pictured.
Lift the handle on top of the
Water to remove the Humidier
from the base.
Make sure the handle is
snapped back into place, then
turn the Water Tank upside
down and remove the Tank Cap
by turning it counter clockwise.
Fill the Water Tank with clean,
cool tap water. Do not use
extremely cold water, since it
may temporarily reduce the
mist output. Never ll with
hot/warm water or add ad-
ditives as this could damage
the unit and void the warranty.
1
2
3
4
4
5
6
8
7
Operating Instructions
NOTE: Do not operate the humidier without water in the tank.
ON/OFF - Plug in to a standard (120V AC) electrical outlet. The LED Display will turn
on for 2 seconds then turn OFF. Press the ON/OFF button once and the “Operating”
indicator will turn on. Mist will not appear immediately; allow up to 15 minutes for the
water in the tank to transfer to the base.
Delay Start – The Delay Start Feature allows you to program the unit to turn ON
Automatically. Press the “Delay Start” button once; you will see “Delay Start” 01:00H
illuminated on the display. This features works in one hour increments and is program-
mable up to 24 hours. Simply keep pressing the Delay Start button until you get to
your desired delay start time, once you have reached the time the display will ash
three times and then will start to countdown until the unit turns ON.
Auto-Off – The Auto-Off feature allows you to program the unit to turn OFF auto-
matically. Press the “Auto-Off’ button once; you will see “Auto-Off” 01:00 illuminated
on the display. This feature works in one hour increments and is programmable up
to 24 hours. Simply keep pressing the Auto-Off button until you get to your desired
Auto-Off time, once you have reach the time the display will ash three times and
then start to count down until the unit turns OFF. The display will start alternating
between the current ambient humidity and the Auto-off Timer.
NOTE: You can use
the Delay Start and Auto-Off functions together on this fully programmable
LED Display to program the Humidier to turn ON and turn OFF at your
desired times.
LED Dim – To turn OFF the LED Display, press the “LED DIM” button once. Press
the “LED DIM” , or any other button on the control panel to turn the display back ON.
LOW Water – When the Tank is out of water the “waterless” indicator will appear
in the display, you will hear 3 beeps and the automatic safety shut-off will turn the
Ultrasonic Nebulizer & unit OFF.
Extension Nozzle – To convert this unit from a Tabletop unit to Floor unit simply
remove the Dual Directional Mist Nozzle from the top of the Water Tank. Place the
unit on your desired oor area and insert the Extension Nozzle into the Top of the
Water Tank. Then place the Dual Directional Nozzle on the top of the Extension
Nozzle. NOTE: Be sure have the unit unplugged and turned off when changing the
Nozzles
Mist Output
–
When you turn the unit ON, it will default to the lowest mist setting. Press-
ing the “Mist” button will increase the output. Press once for Medium, twice for High, three
times for Supreme, four times for the Turbo Setting. Pressing the Mist button a fth time
will bring the unit back to Low. NOTE: Turbo setting is intended for those wanting a
more powerful mist and works best while the Extension Nozzle is being used. The
Turbo setting will operate for 40 minutes and will then go to the Supreme Mist
Setting. User must wait 20 minutes before Turbo setting can be used again.
Humidistat – By using this feature the humidier will automatically control the humidity
level according to your desired setting. If the set humidity is reached the unit will turn
OFF; if the humidity drops below the setting the unit will turn ON automatically. To set
this feature press the “Humidistat” button to your desired setting. Settings range from
40%-95% RH (Relative Humidity) in 5% RH increments. A 40%-60% Relative Humidity
is recommended. The display will start alternating between the Current and Set ambi-
ent humidity.
1
2
3
6
7
8
4
5
5
Weekly Cleaning & Care
CAUTION: Before cleaning always turn power off and unplug the unit from outlet.
DO NOT use any solvents or aggressive cleaning agents. Keep water away from the Air Out-
let. DO NOT tamper with the Water Sensor.
About White Dust - Use of high-mineral content water may cause a white mineral residue to
accumulate on room surfaces near the humidier. The mineral residue is commonly called
“white dust”. The higher the mineral content (the harder your water is), the greater the poten-
tial for white dust. The white dust is not caused by a defect in the humidier, but is due only
to minerals suspended in the water. If you have hard tap water we recommend using only
ltered, distilled, cold boiled or bottled water to minimize the white dust residue.
Tank Cleaning -Remove the Mist Nozzle from the top of the water tank then remove the water
tank from the unit. Turn the tank upside down, unscrew the tank cap and drain any water from
the tank. Wipe the tank with a soft damp cloth then rinse it with warm water inside and out.
Base Cleaning - Gently wipe the base with a soft
damp cloth, do not immerse the Base in water.
Never scrape the Ultrasonic Nebulizer with a hard
or sharp object.
White Dust Cleaning - If mineral deposits
“White Dust” are evident around the Ultrasonic
Nebulizer and Water Sensor, clean these surfaces
with a soft, cloth and a small amount of undiluted
white vinegar. If necessary, mix a solution of 50%
white vinegar and 50% water and ll the Base with
enough solution to cover the Ultrasonic Nebulizer (a).
Allow it to soak for an hour and then use the provided
brush to gently loosen buildup on the
Ultrasonic Nebulizer (b). Rinse out the Base with
clean water and wipe clean with a soft cloth.
Ceramic Water Filter Cleaning - Remove the
Water Tank from the Humidier Base. Remove the
Tank Cap (c) and rinse Water Filter thoroughly with
tap water, then replace on Water Tank (d).
Surface Cleaning - Clean all surfaces of the unit with a clean
damp soft cloth.
CAUTION When emptying the water reservoir on the base, make sure
that the water is poured away from the air outlet (e). If water is poured
into the outlet it may damage the humidier.
Storage
1. Follow all cleaning instructions prior to storage.
2. Dry all parts, including the inside of the Water Tank.
Never leave water inside the tank for several days.
3. Leave the tank cap partially loosened to prolong the life of the cap.
4. Preferably store in its original box, in a dry place away from high temperatures.
5. Follow all cleaning instructions after long periods of storage.
a
e
c
b
d
6
Troubleshooting
PROBLEM: Power Light is OFF
POSSIBLE CAUSES
a. Unit is not plugged in
b. No power at outlet
POSSIBLE SOLUTIONS
a. Plug in power cable
b. Check circuits, fuses,
try a different outlet
c. Press the POWER button to turn
the power on.
PROBLEM: Weak or No mist output
POSSIBLE CAUSES
a. No water in tank
b. Unit is not leveled
c. White Dust on Nebulizer and/or
Water Sensor
d. Blower not operating
e. Water temperature
too low
f. Nebulizer not operating
POSSIBLE SOLUTIONS
a. Fill tank with water and wait 10 – 15 minutes
b. Place unit on level surface.
c. Clean Humidier per instructions.
d. Ensure water in Base is adequate to im-
merse the Water Sensor.
e. Set output to High and wait for
10 – 15 minutes.
f. See Warranty
PROBLEM: Peculiar Odor
POSSIBLE CAUSES
a. If new unit
b. Dirty Water Tank or old water in tank
c. Minerals in well water or hard water
POSSIBLE SOLUTIONS
a. Rinse Water Tank and Base and let air dry
b. Empty old water and clean Water Tank per
instructions.
c. Use ltered, distilled, cold boiled or bottled
water
PROBLEM :White Dust on unit or nearby
furniture
POSSIBLE CAUSE
Hard water used
POSSIBLE SOLUTION
Use ltered, distilled, cold boiled or bottled
water
PROBLEM: Condensation forms
around humidier or windows
POSSIBLE CAUSES
a. Mist output is set too high
for room size
b. Direction of mist nozzle
POSSIBLE SOLUTIONS
a. Decrease mist output
b. Change direction of mist nozzle
PROBLEM: Water is leaking
POSSIBLE CAUSES
a. Tank cap not properly attached
b. Water tank not properly attached
c. Unit is not on level surface
POSSIBLE SOLUTIONS
a. Follow item #4 on “lling the water tank”
b. Follow item #6 on “lling the water tank”
c. Place on level surface
7
Try These Other Great
Products For Your Life!
Available at: www.qvc.com & www.forlifeproducts.com
8
Tabla de contenidos
Otros manuales de Humidificador de AIRINNOVATIONS
AIRINNOVATIONS
AIRINNOVATIONS MH-703 Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS Clean Mist MH-512 Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS CLEAN MIST TOP-FILL SENSA TOUCH Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS CLEAN MIST MH-702A Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS MH-701C Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS Clean Mist Smart Humidifier Manual de usuario
AIRINNOVATIONS
AIRINNOVATIONS clean mist MH-408 Manual de usuario
AIRINNOVATIONS
AIRINNOVATIONS CLEAN MIST MH-419 Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS MH-408 Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS CLEAN MIST MH-701BA Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS MH-602 Manual de usuario
AIRINNOVATIONS
AIRINNOVATIONS CLEAN MIST AI-101 Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS MH-908 Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS PERSONAL HUMIDIFIER Manual de usuario
AIRINNOVATIONS
AIRINNOVATIONS CLEAN MIST SMART HUMIDIFIER MH-512A Platinum Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS MH-908 Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS CLEAN MIST TOP-FILL SMART HUMIDIFIER Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS CLEAN MIST Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS CLEAN MIST TOP FILL SENSA TOUCH MH-526 Manual de instrucciones
AIRINNOVATIONS
AIRINNOVATIONS GH-2193 Manual de instrucciones
