Agri-Fab 45-0382 Manual de usuario

45_0382Cvr

125 LB. PUSH

BROADCAST SPREADER

FORM NO. 49905 (REV. 11/06)

CAUTION:

Read Rules for

Safe Operation

and Instructions

Carefully

Model No.

45-0382

45-0405

• Safety

• Assembly

• Operation

• Maintenance

• Parts

PRINTED IN USA

the fastest way to purchase parts

www.speedepart.com

™

OwNERS MANUAL

RULES FOR SAFE OPERATION

The following precautions are suggested. This broadcast spreader is designed, engineered and tested to offer reasonably

safe and effective service, provided it is operated in strict accordance with these instructions. Failure to do so may result in

personal injury. Always observe the rules of safe operation.

LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS.

IT MEANS — ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED.

1. Do not allow anyone to operate the broadcast spreader without proper instructions.

2. Do not permit children to operate the broadcast spreader.

3. Wear eye and hand protection when handling and when applying lawn or garden chemicals.

4. Read the chemical label instructions and cautions for handling and applying the chemicals purchased for spreading.

5. Keep all nuts, bolts and screws tight to be sure equipment is in safe working condition.

6. Follow maintenance and lubrication instructions as outlined in this manual.

45_0382CarCont

1. Hopper Assembly

2. Wheels (2)

3. Flow Control Bracket

CARTON CONTENTS

LOOSE PARTS IN CARTON

4. Flow Control Lever

5. Flow Control Rod

6. Upper Handle (2)

7. Stand

8. Hopper Screen

Hardware Package (Shown next page)

FULL SIZE

45_382Hardware

(Not Shown Full Size) (Not Shown Full Size)

HARDwARE PACKAGE CONTENTS (Shown full size except where noted)

I 1 Cotter Pin, 5/32 x 2 in.

J 2 Cotter Pin, 9/64 x 1-1/2 in.

K 1 Cotter Pin, 1/8 x 3/4 in.

L 1 Spring

M 1 Wing Nut, 1/4-20 Nylon

N 2 Spacer

O 1 Adjustable Stop

P 2 Handle Grip

Q 1 Flow Control Lever Grip

A 3 Hex Bolt, 1/4-20 x 2-1/2 in. Long

B 8 Hex Bolt, 1/4-20 x 1-1/2 in. Long

C 1 Hex Bolt, 1/4-20 x 3/4 in. Long

D 1 Carr. Bolt,1/4-20 x 3/4 in. Long

E 12 Nylock Nut, 1/4-20

F 3 Washer, 1/4 in. SS

G 1 Washer, Nylon

H 6 Washer, 5/8 ID x 1 in. OD

Key Qty. Description Key Qty. Description

ASSEMBLY INSTRUCTIONS

TOOLS REQUIRED FOR ASSEMBLY

(1) Pliers

(2) 7/16 in. open or boxed end wrenches

1. Remove the spreader, the loose parts and the hardware

package from the carton. Lay out parts and hardware

and identify using the illustrations on pages 2 and 3.

2. With the spreader resting upside down on the top of the

hopper, assemble a 5/8 in. at washer, a spacer and

a second 5/8 in. at washer onto each end of the axle.

See gure 1.

FIGURE 1

6. Install an upper handle to each lower handle using four

1/4 x 1-1/2 in. bolts and nylock nuts. Do not tighten at

this time. See gure 3.

ENGLISH

3. Place a wheel onto each end of the axle. The long end

of the hub goes to the inside. See gure 2.

4. Assemble a 5/32 x 2 in. cotter pin through the hole in

one wheel hub and the axle. See gure 2.

5. Place a 5/8 in. at washer onto each end of the

axle and secure with a 9/64 x 1-1/2 in. cotter pin.

See gure 2.

45_0382Fig3

1/4-20 x 1-1/2 in.

HEX BOLT (B)

1/4-20 NYLOCK

NUT (E)

FIGURE 3

FIGURE 2

45_0382Fig2

5/32 x 2 in.

COTTER PIN (I)

9/64 x 1-1/2 in.

COTTER PIN (J)

5/8 in. FLAT

WASHER (H)

45_0382Fig1

5/8 in. FLAT WASHER (H)

SPACER (N)

FIGURE 4

8. Attach the two upper handles together with

the flow control bracket as shown using three

1/4 x 2-1/2 in. bolts and nylock nuts. Do not tighten

two bolts in ow control bracket. Tighten third bolt in

upper handles. See gure 5.

45_0382Fig4

1/4-20 x 1-1/2 in.

HEX BOLT (B)

1/4-20 NYLOCK

NUT (E)

USE

MIDDLE

HOLE

USE THIS

HOLE

FIGURE 5

7. For the standard setup, use the holes shown in

the illustration. Other hole combinations allow

different handle heights and hopper angles. Do

not use holes in stand that are farthest apart as a

combination - ow gate may not close completely.

Attach the stand to the hopper frame tube using two

1/4 x 1-1/2 in. bolts and nylock nuts. Attach the stand

to the lower handle using two 1/4 x 1-1/2 in. bolts and

nylock nuts. Tighten all four bolts to secure the stand.

See gure 4.

45_0382Fig5

1/4-20 x 2-1/2 in.

HEX BOLT (A)

1/4-20 NYLOCK

NUT (E)

1/4 in. WASHER (F)

11. Attach the spring to the stainless steel pattern plate as

shown. Attach the opposite end of the spring to the 1/8

in. hole in the ow control rod. Rotate the end of the rod

into the ow control link. See gure 7.

45_0382Fig7

SPRING (L)

1/8 in. HOLE

SPRING

ANCHOR

HOLE

FLOW

CONTROL

LINK

FIGURE 7

45_0382Fig6

LEVER

GRIP (Q)

1/4-20 NYLOCK

NUT (E)

1/4 in. NYLON

WASHER (G)

1/4-20 x 3/4 in.

HEX BOLT (C)

HANDLE

GRIP (P)

FIGURE 6

9. Install a handle grip on each handle. See gure 6.

10. Attach the ow control lever to the bracket using one

1/4 x 3/4 in. bolt, nylon washer and nylock nut. Tighten

carefully to allow the lever to move freely. Install the

vinyl grip. See gure 6.

45_0382Fig8

1/8 x 3/4 in.

COTTER PIN (K)

FLOW

CONTROL

ROD

FLOW

CONTROL

LEVER

45_0382Fig11

POSITION 5

ADJUSTABLE

STOP

1/4 in. NYLOCK NUTS

FIGURE 11

FIGURE 8

12. Insert the end of the ow control rod through the slot in

the ow control mounting bracket and through the hole

in the ow control lever. Secure with a 1/8 in. x 3/4 in.

cotter pin. See gure 8.

45_0382Fig1045_0382Fig10

ADJUSTABLE

STOP

OFF

FIGURE 10

14. Adjust the position of the ow control mounting bracket

(gures 10 and 11):

a. Set the adjustable stop at “5.” Latch the ow control

lever against the stop. Verify that the closure plate

has opened about halfway. See gure 10.

b. If closure plate is not open halfway, adjust the position

of the ow control mounting bracket until the closure

plate is open about halfway at “5” and still closed when

the lever is in the “OFF” position. Carefully tighten

the 1/4 in. nylock nuts. Do not deform the slots in the

ow control mounting bracket.

c. Push the ow control lever to the “OFF” position

and ensure the closure plate closes completely.

See gure 11.

13. Install the adjustable stop on the slot in the top of

the ow control mounting bracket. Secure with the

1/4 in. x 3/4 in. carriage bolt, a nylon washer, a 1/4 in.

at washer and the nylon wing nut. See gure 9.

45_0382Fig945_0382Fig9

ADJUSTABLE

STOP (O)

1/4-20 WING NUT (M)

1/4-20 x 3/4 in.

CARRIAGE BOLT (D)

1/4 in. WASHER (F)

FIGURE 9

15. Place the hopper screen down into the hopper, sliding

the ends into the clips in the hopper. The screen helps

break up clumpy material and prevents large clumps

from reaching the bottom of the hopper and clogging

the opening. See gure 12.

HOPPER

SCREEN

FIGURE 12

16. Lubricate the spreader following the instructions in the

MAINTENANCE section on page 9.

1. To adjust the ow to be heavier to the left side,

tighten the thumbscrew so the plate is pushed inward.

See gure 13

2. To adjust the ow to be heavier to the right side,

loosen the thumbscrew so the plate is pulled outwards.

See gure 13

OPERATION

HOw TO USE YOUR SPREADER

SETTING THE FLOw CONTROL

(Refer to gure 10 on page 6.)

1. Loosen the nylon wing nut, set the adjustable stop to

the desired ow rate setting and retighten the wing nut.

The higher the setting number, the wider the opening

in the bottom of the hopper.

2. Refer to the Application Chart on page 8 and to the

instructions on the fertilizer bag to select the proper

ow rate setting.

3. Pull the ow control lever back and latch to the adjustable

stop for the “ON” position. Unlatch and push toward the

hopper for the “OFF” position.

USING THE PATTERN ADJUSTMENT PLATE

The pattern adjustment plate is used to adjust the ow of

material being spread to the left or right side. The pattern

adjustment plate is located between the gate opening and

the spreader plate.

The adjustment of the pattern plate is sensitive and it is

recommended to test your spread pattern in a small area

rst.

45_0382Fig16

THUMB SCREW

USING YOUR SPREADER

The use of powdered lawn chemicals is not recommended,

due to difculty in obtaining a satisfactory or consistent

broadcast pattern.

1. Determine approximate square footage of area to be

covered and estimate amount of material required.

2. Before lling the hopper, make sure the ow control lever

is in the “OFF” position and the closure plate is shut.

3. Break up any lumpy fertilizer as you ll the hopper.

4. Set the adjustable stop with the ow control lever still

in the “OFF” position. Refer to the Application Chart on

page 8 and to the instructions on the fertilizer bag to

select the proper ow rate setting.

5. The Application Chart on page 8 is calculated for light-

to-heavy application at a walking speed of 3 mph, or

100 ft. in 23 seconds. A variation in speed will require

an adjustment of the ow rate to maintain the same

coverage.The faster you walk, the wider the broadcast

width.

6. Always start the spreader in motion before opening the

closure plate.

7. Always shut the closure plate before turning or stopping

the spreader.

8. If fertilizer is accidentally deposited too heavily in a small

area, soak the area thoroughly with a garden hose or

sprinkler to prevent burning of the lawn.

FIGURE 13

APPLICATION DIAGRAM

IMPORTANT: Application rates shown in the chart are

affected by humidity and by the moisture content of

the material (granular and pellet). Some minor setting

adjustments may be necessary to compensate for this

condition.

APPLICATION CHART

MATERIAL

TYPE

FLOW SETTING

3 MPH

(100 FT. IN 23 SEC.)

SPREAD

WIDTH IN

FEET

FERTILIZER

Powder

Granular

Pelleted

Organic

GRASS SEED

Fine

Coarse

ICE MELTER

3-5

6-8

3-4

4-5

6-8

3-4

8-10

10-12

6-8

6-7

8-9

10-12

OPERATING SPEED - 3 MPH. (100 ft. in 23 seconds)

OVERLAP

8' to

10'

FIGURE 14

9. To insure uniform coverage, make each pass so that the

broadcast pattern slightly overlaps the pattern from the

previous pass as shown in gure 14. The approximate

broadcast widths for different materials are shown in

the Application Diagram gure 14.

10. When broadcasting weed control fertilizers, make sure

the broadcast pattern does not hit evergreen trees,

owers or shrubs.

MAINTENANCE

CHECK FOR LOOSE FASTENERS

1. Before each use, make a thorough visual check of

the spreader for any bolts and nuts which may have

loosened. Retighten any loose bolts and nuts.

CHECK FOR wORN OR DAMAGED PARTS

2. Check for worn or damaged parts before each use.

Repair or replace parts if necessary.

CHECK TIRE INFLATION

3. Check if tires are adequately inated before each use.

Do not inate tires beyond maximum recommended

pressure on tire.

CLEANING

4. Rinse inside of hopper and exterior of spreader and

allow to dry before storing.

LUBRICATE (See gure 15)

5. Remove one small and two large hairpins and separate

the gearbox housings.

6. Lightly apply automotive grease as needed to the

sprocket and gear.

7. Oil the nylon bushings on the vertical sprocket shaft.

Apply grease to the axle at least once a year, or more

often as needed.

8. Oil (idler) wheel at least once a year or more often as

needed.

9. Install gearbox housings and secure with hairpins.

STORAGE

1. Rinse inside of hopper and exterior of spreader and

allow to dry before storing.

2. Store in a clean, dry area.

SERVICE AND ADJUSTMENTS

1. If the axle and gear assembly is disassembled, mark

down the positions of the parts as they are removed.

The drive wheel and large gear positions, in relation

to the small gear, determine which direction the

spreader plate will spin. Be sure to reassemble them

in their original positions. (Refer to parts exploded

view on page 10). Ensure washer (Refer to item 25

on page 10 and 11) is in place when assembling the

axle components. Add grease to gears.

2. If the agitator hairpin becomes damaged or worn, it

can be replaced. Remove old agitator hairpin from

hole in sprocket shaft and replace with new agitator

hairpin. See gure 16.

OIL

GREASE

HAIRPIN

FIGURE 15

SPROCKET

SHAFT

AGITATOR

HAIRPIN

FIGURE 16

CAUTION: DO NOT inate tires beyond the

maximum recommended pressure printed

on side of tire.

REPAIR PARTS FOR BROADCAST SPREADER

MODEL 45-0382 AND 45-0405

26 23

66 7

12 9

4242 4

21 5

5425

39 425

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Esparcidor de Agri-Fab

Agri-Fab

Agri-Fab 45-02101-101 Manual de usuario

Agri-Fab

Agri-Fab 45-03641 Manual de usuario

Agri-Fab

Agri-Fab 45-0301 Manual de usuario

Agri-Fab

Agri-Fab 45-03881 Manual de usuario

Agri-Fab

Agri-Fab 45-046 Manual de usuario

Agri-Fab

Agri-Fab 45-05321 Manual de usuario

Agri-Fab

Agri-Fab 45-04631 Manual de usuario

Agri-Fab

Agri-Fab 45-02114 Manual de usuario

Agri-Fab

Agri-Fab 45-02103-101 Manual de usuario

Agri-Fab

Agri-Fab Agri-Fab 45-03153 Manual de usuario

Agri-Fab

Agri-Fab 45-02102-101 Manual de usuario

Agri-Fab

Agri-Fab 45-0315 Manual de usuario

Agri-Fab

Agri-Fab 45-0313 Manual de usuario

Agri-Fab

Agri-Fab 45-02881 Manual de usuario

Agri-Fab

Agri-Fab 45-03153 Manual de usuario

Agri-Fab

Agri-Fab 45-02113 Manual de usuario

Agri-Fab

Agri-Fab 45-02152 Manual de usuario

Agri-Fab

Agri-Fab 45-0329 Manual de usuario

Agri-Fab

Agri-Fab 45-02141 Manual de usuario

Agri-Fab

Agri-Fab 45-02111 Manual de usuario

Agri-Fab

Agri-Fab 45-0527 Manual de usuario

Agri-Fab

Agri-Fab 175 Manual de usuario

Agri-Fab

Agri-Fab 45-03295 Manual de usuario

Agri-Fab

Agri-Fab 45-2142 Manual de usuario

Manuales populares de Esparcidor de otras marcas

PEQUEA

PEQUEA GT-100 Manual de usuario

Herculano

Herculano H2RS9 Manual de usuario

Epoke

Epoke SKE8 Manual de usuario

GEA

GEA EL44 Hoja de especificaciones

Boss Snowplow

Boss Snowplow TGS 800 Manual de usuario

Fisher

Fisher EMERSON 168 Series Manual de usuario

Fisher

Fisher POLY-CASTER 78601 Manual de usuario

TurfEx

TurfEx RS7200 Manual del propietario

Ferris

Ferris Pathfinder Series Manual de usuario

Fayat Group

Fayat Group DYNAPAC S100 Guía de solución de problemas

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Manual de instalación y operación

EASTMAN

EASTMAN CR 500 Manual de usuario

Nogueira

Nogueira RoyalFlow-600 Manual de usuario

Buyers

Buyers TGS05B Manual de usuario

Magnum

Magnum V-BOX PV Series Suplemento

Meyer's

Meyer's VB280 Manual de usuario

SnowEx

SnowEx VX-4210 Manual de usuario

Kramer

Kramer VM-400HDCP Manual de usuario