Agri-Fab 45-02103-101 Manual de usuario

CAUTION:

Read Rules for

Safe Operation

and Instructions

Carefully

125 LB. PUSH

BROADCAST SPREADER

PRINTED IN U.S.A. FOR NO. 49120 (12/03)

OWNERS

MANUAL

Model No.

45-02103-101

Assembly

Operation

aintenance

Repair Parts

the fastest way to purchase parts

www.speedepart.com

Agri-Fab¨

SHIELD UP - 8 TO 18 FT. SPREAD WIDTH

SHIELD DOWN - 3 TO 4 FT. SPREAD WIDTH

RULES FOR SAFE OPERATION

The following safety precautions are suggested. This

broadcast spreader is designed, engineered and tested

to offer reasonably safe and effective service, provided it

is operated in strict accordance with these instructions.

Failure to do so may result in personal injury. Always

observe the rules of safe operation.

1. Do not allow anyone to operate the broadcast

spreader without proper instructions.

2. Do not permit children to operate the broadcast

spreader.

3. Wear eye and hand protection when handling and

when applying lawn or garden chemicals.

4. Read the chemical label instructions and cautions

for handling and applying the chemicals purchased

for spreading.

5. Keep all nuts, bolts and screws tight to be sure

equipment is in safe working condition.

6. Follow maintenance and lubrication instructions as

outlined in this manual.

LOOK FOR THIS SY BOL TO POINT OUT I PORTANT SAFETY PRECAUTIONS. IT

EANS -- ATTENTION! BECO E ALERT! YOUR SAFETY IS INVOLVED.

234

910 11

CARTON CONTENTS

LOOSE PARTS IN CARTON

1. Hopper Assembly

2. Wheel

3. Spreader Shield

4. Braces (2)

5. Flow Control Rod

6. Vinyl Hopper Cover

7. Hopper Screen

8. Handle Tube (short)

9. Flow Control Arm

10. Handle Tube (long)

11. Leg Stand Tube

12. Flow Control ount Bracket

Hardware Package (page 3)

KEY QTY. DESCRIPTION

A 2 Hex Bolt, 1/4-20 x 1-3/4" Long

B 5 Hex Bolt, 1/4-20 x 1-1/2" Long

C 8 Hex Bolt, 1/4-20 x 1" Long

D 3 Carriage Bolt, 1/4-20 x 3/4" Long

E 15 Nylock Nut, 1/4-20 Thd.

F 20 Flat Washer, 5/16" SAE

G 8 Nylon Washer

H 4 Flat Washer, 5/8"

I 1 Cotter Pin, 5/32" x 2"

J 1 Cotter Pin, 3/32" x 3/4" Long

KEY QTY. DESCRIPTION

K 1 Flow Control Link

L 2 Spacer Tube

2 Hub Cap

N 1 Grip

O 1 Vinyl Cap

P 1 Nylon Wing Nut

Q 2 Handle Grip

R 1 Adjustable Stop

S 4 Swivel Bracket

T 2 Angle Stop Bracket

U 2 Plastic Knob

NOT FULL SIZE

FULL SIZE

A B C

KLMNO

S T U

ASSEMBLY INSTRUCTIONS

TOOLS REQUIRED FOR ASSEMBLY

(1) Pliers

(1) Hammer

(2) 7/16" Open or Boxed End Wrenches

1. Remove the spreader, the loose parts and the hard-

ware package from the carton. Lay out parts and

hardware and identify using the illustrations on

pages 2 and 3.

2. With the spreader resting upside down on the top of

the hopper, assemble a spacer and then a 5/8" flat

washer onto each end of the axle. See figure 1.

FIGURE 2

FIGURE 1

FIGURE 3

5. Place a wheel onto the end of the axle that has a

cross hole. The long end of the hub goes to the

inside. See figure 3.

6. Assemble a 5/32" x 2" cotter pin through the hole in

the wheel hub and the axle. See figure 3.

7. Place a 5/8" flat washer onto the axle and then

lightly tap a hub cap onto the axle until it is snug

against the washer and wheel hub. See figure 3.

FIGURE 4

3. Place a wheel onto the end of the axle that has no

cross hole. The long end of the hub goes to the

inside. See figure 2.

4. Place a 5/8" flat washer onto the axle and then

lightly tap a hub cap onto the axle until it is snug

against the washer and wheel hub. See figure 2.

AXLE

SPACER

5/8" FLAT

WASHER

5/8" FLAT

WASHER

HUB CAP

WHEEL

NO CROSS HOLE

HUB CAP

5/32" x 2"

COTTER PIN

CROSS

HOLE

5/8" FLAT

WASHER

8. Remove the nut from the middle bolt in the crossover

tube. See figure 4.

CROSSOVER

TUBE

MIDDLE NUT

SHAFT

SUPPORT

PLATE

MIDDLE BOLT

FIGURE 7

13. Assemble the leg stand tube to the handle tube

(long) using two 1/4" x 1-1/2" hex bolts. Secure

tightly with two 1/4" nylock nuts. See figure 6.

14. Place a vinyl cap over the end of the leg stand tube.

See figure 6.

FIGURE 5

FIGURE 6

15. Assemble the flow control link (end with small hole)

to the flow control arm using a 1/4" x 1" hex bolt, a

nylon washer and a 1/4" nylock nut as shown in

figure 7. Tighten carefully. The flow control link

should not be loose but should pivot with no more

than slight resistance.

HANDLE TUBE (LONG)

1/4" x 1-1/2"

HEX BOLTS

1/4"

NYLOCK

NUTS

VINYL CAP LEG STAND TUBE

IMPORTANT: Do Not assemble handle tube to same

side of crossover tube as shaft support plate.

9. Place the long handle tube onto the crossover

tube on the side opposite from the shaft support

plate. Fasten with the bolt, washer and nut re-

moved in the previous step. See figures 4 and 5.

Do not tighten at this time.

10. Assemble two handle braces to the inside of the

hopper frame, one on each side, using two 1/4" x

1-1/2" hex bolts and two 1/4" nylock nuts. See

figure 5. Do not tighten at this time.

11. Assemble the other end of the two handle braces

to the long handle tube using a 1/4" x 1-1/2" hex

bolt and 1/4" nylock nut. Do not tighten at this

time. See figure 5.

12. Tighten all nuts and bolts in same sequence as

assembled in steps 9 through 11. See figure 5.

MIDDLE

BOLT

MIDDLE

NUT

HANDLE TUBE (LONG)

HEX BOLT

1/4" x 1-1/2"

HEX BOLT

1/4" x 1-1/2"

HITCH

BRACE

1/4"

NYLOCK

NUT

CROSSOVER

TUBE

SHAFT

SUPPORT

PLATE

FLOW CONTROL

LINK FLOW

CONTROL

ARM

1/4"

NYLOCK

NUT

1/4" x 1"

HEX BOLT

SMALLEST

HOLE

NYLON

WASHER

FIGURE 8

FIGURE 9

19. Hook the free end of the flow control rod through the

hole in the slide gate bracket located near the

bottom of the hopper. See figure 10.

FIGURE 10

FIGURE 11

16. Assemble the flow control arm to the flow control

mounting bracket using a 1/4" x 1" hex bolt, two

nylon washers and a 1/4" nylock nut as shown in

figure 8. Tighten carefully. The flow control arm

should be snug, but should pivot with no more than

a slight resistance.

17. Assemble the vinyl grip. See figure 8.

18. Place a 5/16" flat washer onto the end of the flow

control rod. Insert the end of the flow control rod

through the slot in the flow control mounting bracket

and through the hole in the flow control link. Secure

with a 3/32" x 3/4" cotter pin. See figure 9.

20. Assemble both the flow control mounting bracket

and the short handle tube to the long handle tube.

Use two 1/4" x 1-3/4" hex bolts, four 5/16" flat

washers and two 1/4" nylock nuts as shown in figure

11. Do not tighten at this time.

21. Place a handle grip on each handle. See figure 11.

1/4" x 1-3/4"

HEX BOLT

1/4"

NYLOCK

NUT

HANDLE

TUBE

(SHORT)

HANDLE

TUBE

(LONG)

HANDLE GRIP FLOW CONTROL

MOUNTING BRACKET

5/16"

FLAT

WASHERS

HOPPER

SLIDE

GATE

BRACKET

FLOW

CONTROL

ROD

FLOW

CONTROL

ROD

FLOW

CONTROL

LINK

3/32"

COTTER

5/16" FLAT

WASHER

SLOT

1/4" x 1"

HEX BOLT

1/4"

NYLOCK

NUT

FLOW CONTROL

MOUNTING

BRACKET

FLOW

CONTROL

ARM

(2) NYLON

WASHERS

VINYL GRIP

FIGURE 12

22. Place the adjustable stop into the "ON" end of the

slot in the top of the flow control mounting bracket.

Secure with the 1/4" x 3/4" carriage bolt, a nylon

washer, a 5/16" flat washer and the nylon wing nut.

See figure 12.

23. Position the flow control mounting bracket (figure

13).

a. Push on flow control arm until it locks in "OFF"

position.

b. Slide flow control mounting bracket along tube

until closure plate in bottom of hopper just closes.

c. Snug the 1/4" lock nuts just enough to hold flow

control mounting bracket in place.

d. Set adjustable stop at "5". Pull flow control arm

against stop. Verify that closure plate has opened

about half way.

e. If closure plate does not open half way, it may be

closed too far at "OFF". Adjust position of flow

control mounting bracket until closure plate will

open about half way at "5" and still close when

arm is locked in "OFF". Tighten 1/4" lock nuts.

5/16" FLAT

WASHER

NYLON

WASHER

1/4" x 3/4"

CARRIAGE BOLT

NYLON

WING NUT

ADJUSTABLE

STOP

OFF

FLOW

CONTROL

ARM

OFF

AJDUSTABLE

STOP

SETTING "5"

FIGURE 13

26. Assemble the spreader shield to the front swivel

brackets using two 1/4" x 3/4" carriage bolts, 5/16"

washers and the two 1/4" plastic knobs. See figure

15.

27. Assemble the spreader shield to the rear swivel

brackets using two 1/4" x 1" hex bolts, four 5/16"

washers and two 1/4" Nylock nuts. Tighten the nuts

so that the swivel bracket can still pivot freely. See

figure 15.

28. Place the hopper screen down into the hopper to help

break up clumpy material and to prevent large clumps

from reaching the bottom of the hopper and clogging

the opening. See figure 16.

24. Attach an angle stop bracket and a swivel bracket to

the rear hole in the R.H. shield bracket using a 1/4" x

1" hex bolt, two 5/16" washers, a nylon washer and a

1/4" Nylock nut. Place the angle stop bracket on the

inside and the swivel bracket on the outside. Tighten

the locknut so that the swivel bracket can pivot freely.

See figure 14. Repeat step on L.H. shield bracket.

25. Attach a swivel bracket to the front hole in the R.H.

shield bracket using a 1/4" x 1" hex bolt, two 5/16"

washers, a nylon washer and a 1/4" Nylock nut.Tighten

the nut so that the swivel bracket can pivot freely. See

figure 14. Repeat step on L.H. shield bracket.

SWIVEL

BRACKET

ANGLE STOP

BRACKET

1/4" x 1"

HEX BOLT

5/16"

WASHER

1/4" NYLOCK

NUT

NYLON

WASHER

SHIELD

BRACKET

NYLON

WASHER

1/4" x 1"

HEX BOLT

5/16" WASHER

1/4" NYLOCK NUT

PLASTIC

KNOB

1/4" x 3/4"

CARRIAGE BOLT

SHI

ELD UP

HOPPER SCREEN

FIGURE 15

FIGURE 16

FIGURE 14

29. Lubricate the spreader following the instructions in the

maintenance section on page 11.

HOW TO USE YOUR SPREADER

SETTING THE FLOW CONTROL

(Refer to figure 13 on page 7.)

1. Loosen the nylon wing nut, set the adjustable stop to

the desired flow rate setting and retighten the wing

nut. The higher the setting number, the wider the

opening in the bottom of the hopper.

2. Refer to the application chart on page 10 and to the

instructions on the fertilizer bag to select the proper

flow rate setting.

3. Pull the flow control arm against the adjustable stop

for the on position and toward the hopper for the off

position.

OPERATION

USING YOUR SPREADER

We do not recommend the use of any powdered lawn

chemicals, due to difficulty in obtaining a satisfactory or

consistent broadcast pattern.

1. Determine approximate square footage of area to be

covered and estimate amount of material required.

2. Before filling the hopper make sure the flow control

arm is in the off position and the closure plate is shut.

3. Break up any lumpy fertilizer as you fill the hopper.

4. Set the adjustable stop with the flow control arm still in

the off position. Refer to the application chart on page

10 and to the instructions on the fertilizer bag to select

the proper flow rate setting.

5. The application chart is calculated for light to heavy

application at a walking speed of 3 mph, or 100 ft. in

23 seconds. A variation in speed will require an

adjustment of the flow rate to maintain the same

coverage. The faster you walk, the wider the broad-

cast width.

6. Always start the spreader in motion before opening

the closure plate.

7. Always shut the closure plate before turning or stop-

ping the spreader.

8. If fertilizer is accidentally deposited too heavily in a

small area, soak the area thoroughly with a garden

hose or sprinkler to prevent burning of the lawn.

9. To insure uniform coverage, make each pass so that

the broadcast pattern slightly overlaps the pattern

from the previous pass as shown in figure 17. The

approximate broadcast widths for different materials

are shown in the application chart on this page.

10. When broadcasting weed control fertilizers, make

sure the broadcast pattern does not hit evergreen

trees, flowers or shrubs. Lower the spreader shield to

limit the dispersal pattern. Reduce the flow control

setting according to the application chart on page 10.

FIGURE 17

APPLICATION DIAGRAM

11. Heavy moisture conditions may require a cover over

the hopper to keep contents dry. The vinyl cover

(available as an accessory) acts as a wind and mois-

ture shield, but should not be used as a rain cover.

Refer to the parts list on page 13.

OVERLAP

8’ to

10’

OVERLAP

3’ to

4’

SHIELD UP

SHIELD DOWN

IMPORTANT: Application rates shown in the chart are

affected by humidity and by the moisture content of the

material (granular and pellet). Some minor setting

adjustments may be necessary to compensate for this

condition.

OPERATING SPEED - 3 PH. (100 ft. in 23 seconds)

TYPE FLOW SETTING SPREAD

ATERIAL 3 PH WIDTH

(100 FT. IN 17 SEC.) IN FEET

APPLICATION CHART (SHIELD DOWN)

FERTILIZER

Powder 1 - 3 3 - 4

Granular 1 - 3 3 - 4

Pelleted 1 - 3 3 - 4

Organic 3 - 4 3 - 4

GRASS SEED

Fine 1 - 3 3 - 4

Coarse 2 - 3 3 - 4

ICE ELTER 2 - 4 3 - 4

TYPE FLOW SETTING SPREAD

ATERIAL 3 PH WIDTH

(100 FT. IN 23 SEC.) IN FEET

APPLICATION CHART (SHIELD UP)

FERTILIZER

Powder 3 - 5 3 - 4

Granular 3 - 5 8 - 10

Pelleted 3 - 5 10 - 12

Organic 6 - 8 6 - 8

GRASS SEED

Fine 3 - 4 6 - 7

Coarse 4 - 5 8 - 9

ICE ELTER 6 - 8 10 - 12

Tabla de contenidos

Otros manuales de Esparcidor de Agri-Fab

Agri-Fab

Agri-Fab 45-0364 Manual de usuario

Agri-Fab

Agri-Fab 45-0187 Manual de usuario

Agri-Fab

Agri-Fab 45-01872 Manual de usuario

Agri-Fab

Agri-Fab 45-0313 Manual de usuario

Agri-Fab

Agri-Fab 45-03641 Manual de usuario

Agri-Fab

Agri-Fab 45-02103 Manual de usuario

Agri-Fab

Agri-Fab 45-03153 Manual de usuario

Agri-Fab

Agri-Fab 45-05321 Manual de usuario

Agri-Fab

Agri-Fab 45-02142 Manual de usuario

Agri-Fab

Agri-Fab 45-0315 Manual de usuario

Agri-Fab

Agri-Fab 45-0301 Manual de usuario

Agri-Fab

Agri-Fab 45-03152 Manual de usuario

Agri-Fab

Agri-Fab PRO 125 Manual de usuario

Agri-Fab

Agri-Fab 45-02112 Manual de usuario

Agri-Fab

Agri-Fab SpeedEPart 45-0463 Manual de usuario

Agri-Fab

Agri-Fab 45-04631 Manual de usuario

Agri-Fab

Agri-Fab 45-0301 Manual de usuario

Agri-Fab

Agri-Fab 45-02114 Manual de usuario

Agri-Fab

Agri-Fab 45-03882-KD Manual de usuario

Agri-Fab

Agri-Fab 45-02101-101 Manual de usuario

Agri-Fab

Agri-Fab 45-0566 Manual de usuario

Agri-Fab

Agri-Fab 45-02141 Manual de usuario

Agri-Fab

Agri-Fab 175 Manual de usuario

Agri-Fab

Agri-Fab 45-0309 Manual de usuario

Manuales populares de Esparcidor de otras marcas

PEQUEA

PEQUEA GT-100 Manual de usuario

Herculano

Herculano H2RS9 Manual de usuario

Epoke

Epoke SKE8 Manual de usuario

GEA

GEA EL44 Hoja de especificaciones

Boss Snowplow

Boss Snowplow TGS 800 Manual de usuario

Fisher

Fisher EMERSON 168 Series Manual de usuario

Fisher

Fisher POLY-CASTER 78601 Manual de usuario

TurfEx

TurfEx RS7200 Manual del propietario

Ferris

Ferris Pathfinder Series Manual de usuario

Fayat Group

Fayat Group DYNAPAC S100 Guía de solución de problemas

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Manual de instalación y operación

EASTMAN

EASTMAN CR 500 Manual de usuario

Nogueira

Nogueira RoyalFlow-600 Manual de usuario

Buyers

Buyers TGS05B Manual de usuario

Magnum

Magnum V-BOX PV Series Suplemento

Meyer's

Meyer's VB280 Manual de usuario

SnowEx

SnowEx VX-4210 Manual de usuario

Kramer

Kramer VM-400HDCP Manual de usuario