Aesculap Econom CL Manual de usuario

Aesculap

Econom CL

Econom CL Equipe

Econom CL Fitter

Bruksanvisning/Teknisk Beskrivelse

Klippemaskin til storfe og hest

Econom CL (GT800)

Econom CL Set 1 batteri (GT804)/2 batterier (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 batteri (GT814)/2 batterier (GT816)

Econom CL Fitter Set 1 batteri (GT834)

Bruksanvisning/Teknisk Beskrivning

Nötkreaturs- och hästklippmaskin

Econom CL (GT800)

Econom CL Set 1 batteri (GT804)/2 batterier (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 batteri (GT814)/2 batterier (GT816)

Econom CL Fitter Set 1 batteri (GT834)

Käyttöohjeet/Tekninen Kuvaus

Karjan ja hevosen klipperi

Econom CL (GT800)

Econom CL Set 1 akku (GT804)/2 akkuja (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 akku (GT814)/2 akkuja (GT816)

Econom CL Fitter Set 1 akku (GT834)

Инструкция по примению/Техническое описание

Машинка для стрижки крупного рогатого скота и лошадей

Econom CL (GT800)

Econom CL Set 1 аккумулятор (GT804)/2 аккумулятора (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 аккумулятор (GT814)/

2 аккумулятора (GT816)

Econom CL Fitter Set 1 аккумулятор (GT834)

Instrukcja u¿ytkowania/Opis Techniczny

Maszynka do strzy¿enia sierœci bydlêcej i koñskiej

Econom CL (GT800)

Econom CL Set 1 akumulator (GT804)/2 akumulatory (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 akumulator (GT814)/2 akumulatory (GT816)

Econom CL Fitter Set 1 akumulator (GT834)

取扱説明書

動物用バリカン

Econom CL (GT800)

Econom CL Set 1 バッテリー (GT804)/2 つのバッテリー (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 バッテリー (GT814)/2 つのバッテリー (GT816)

Hebräisch

Klippemaskine til kvæg og heste

Econom CL (GT800)

Econom CL Set 1 Akku (GT804)/2 Akkus (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 Akku (GT814)/2 Akkus (GT816)

Econom CL Fitter Set 1 Akku (GT834)

Instructions for use/Technical description

Cattle and horse clipping machine

Econom CL (GT800)

Econom CL Set 1 battery (GT804)/2 batteries (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 battery (GT814)/2 batteries (GT816)

Econom CL Fitter Set 1 battery (GT834)

Gebrauchsanweisung/Technische Beschreibung

Rinder- und Pferdeschermaschine

Econom CL (GT800)

Econom CL Set 1 Akku (GT804)/2 Akkus (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 Akku (GT814)/2 Akkus (GT816)

Econom CL Fitter Set 1 Akku (GT834)

Mode d’emploi/Description technique

Tondeuse pour la tonte des bovins et chevaux

Econom CL (GT800)

Econom CL Set 1 batterie (GT804)/2 batteries (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 batterie (GT814)/2 batteries (GT816)

Econom CL Fitter Set 1 batterie (GT834)

Instrucciones de manejo/Descripción técnica

Máquina para bovinos y caballos

Econom CL (GT800)

Econom CL Set 1 batería (GT804)/2 baterías (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 batería (GT814)/2 baterías (GT816)

Econom CL Fitter Set 1 batería (GT834)

Istruzioni per l’uso/Descrizione tecnica

Tosatrice per bovini ed equini

Econom CL (GT800)

Econom CL Set 1 accumulatore (GT804)/2 accumulatori (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 accumulatore (GT814)/2 accumulatori (GT816)

Econom CL Fitter Set 1 accumulatore (GT834)

Gebruiksaanwijzing/Technische Beschrijving

Tondeuze voor runderen en paarden

Econom CL (GT800)

Econom CL Set 1 accu (GT804)/2 accu’s (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 accu (GT814)/2 accu’s (GT816)

Econom CL Fitter Set 1 accu (GT834)

Brugsanvisning/Teknisk Beskrivelse

Klippemaskine til kvæg og heste

Econom CL (GT800)

Econom CL Set 1 akkumulator (GT804)/2 akkumulatorer (GT806)

Econom CL Equipe (GT810)

Econom CL Equipe Set 1 akkumulator (GT814)/2 akkumulatorer (GT816)

Econom CL Fitter Set 1 akkumulator (GT834)

234

36 37/38 39

37/38 39

CDE

11 8

Econom CL/Econom CL Equipe/Econom CL Fitter cattle and horse clipping machine

Aesculap®

Overview Symbols on product

Contents

1. Safe handling .................................................................................................. 3

2. Product description ....................................................................................... 3

2.1 Package includes............................................................................................ 3

2.2 Components required for operation ......................................................... 3

2.3 Intended use.................................................................................................... 3

2.4 Operating principle........................................................................................ 4

3. Preparation ...................................................................................................... 4

4. Working with the battery-operated clipping machine, charger

and lithium ion battery................................................................................ 4

4.1 System set-up ................................................................................................. 4

4.2 Function check................................................................................................ 4

4.3 Connecting the charger/Charging the Li-ion battery.......................... 5

4.4 Change the Li-ion battery ........................................................................... 5

4.5 Handling the cutter head ............................................................................ 6

4.6 Storage.............................................................................................................. 7

5. Cutter plates.................................................................................................... 7

5.1 Cutter plates compatible with cutter head GT367 .............................. 7

5.2 Recommended combinations ..................................................................... 7

6. Reprocessing ................................................................................................... 8

6.1 Cleaning/disinfection.................................................................................... 8

6.2 Inspection and checking .............................................................................. 8

7. Maintenance ................................................................................................... 8

8. Troubleshooting.............................................................................................. 9

8.1 Battery-operated clipping machine Econom CL/

Econom CL Equipe/Econom CL Fitter ....................................................... 9

8.2 Charger and Li-ion battery....................................................................... 10

9. Technical Service......................................................................................... 11

10. Accessories/Spare parts............................................................................. 11

11. Technical Data ............................................................................................. 12

11.1 Battery-operated clipping machine Econom CL/

Econom CL Equipe/Econom CL Fitter ......................................................12

11.2 Charger .......................................................................................................... 12

11.3 Li-ion battery ............................................................................................... 12

11.4 Declaration of conformity ........................................................................ 12

12. Disposal.......................................................................................................... 12

12.1 For EU countries only................................................................................. 12

12.2 Li-ion battery ............................................................................................... 12

13. Two year guarantee.................................................................................... 13

Pos. Art. no. Number Name

1GT502 1

Lower cutter plate (GT804–GT816/GT834)

2GT501 1 Upper cutter plate (GT804/GT806/GT834)

GT505 1 Upper cutter plate (GT814/GT816)

3GT610405 1 Knurled nut

4GT367205 1 Adjusting screw

6TA010017 2 Drive pin

7GT367201 1 Oscillator

8GT610304 1 Oscillating block

9GT610010 2 Fixing screw

10 GT367202 6 Oscillating spring leaf

11 GT367812 1 Spur gear with eccentric shaft

15 TA008295 2 Guide pin

16 GT367801 1 Mounted cutter head housing

17 TA005091 2 Drive pin

18 GT367802 1 Left distance part

19 GT367803 1 Right distance part

20 TA007765 1 Countersunk screw

25 GT610307 1 Spring bridge

26 GT367207 1 Fixation screw

27 GT367804 1 Mounted oscillator

35 TA009222 1 Screwdriver

36 GT800249 1 On/off button (with LED)

37 GT800804 1 Airfilter (blue)

Econom CL

38 GT800844 1 Airfilter (bordeaux)

Econom CL Equipe

39 GT801 1 Lithium ion battery

40 GT803 1 Charger

a– 1 Lubricating point for battery-operated

clipping machine

b– 1 Tips of the oscillator

c– 1 Holes in the upper cutter plate

d– 1 Li-ion battery charging status display

e– 1 Li-ion battery button

f– 1 Battery lock

gGT800/

GT810

1IntheUK

– GT604 1 Special lubricating oil for cutter head

and cutter plates

GT605 1 Gear grease (tube)

Caution, general warning symbol

Caution, see documentation supplied with the product

Labeling of electrical and electronic devices according

to directive 2012/19/EU (WEEE), see Disposal

1. Safe handling

¾Prior to use, check that the product is in good working order.

¾Store the charger and Li-ion batteries at room temperature.

¾Keep dry the charger and Li-ion batteries.

¾Charge the Li-ion batteries prior to first use.

¾To prevent damage caused by improper setup or operation, and to not

compromise the manufacturer warranty and liability:

– Use the product only according to these instructions for use.

– Follow the safety and maintenance instructions.

– Only combine Aesculap products with each other.

¾Keep the instructions for use accessible for the user.

¾Always adhere to applicable standards.

¾Ensure that the electrical facilities in the room in which the device is

being used conform to IEC norms.

¾Unplug the device by pulling the plug, but never by pulling the power

cord.

¾Do not operate the product in explosion-hazard areas.

¾Do not use the product if it is damaged or defective. Set aside the

product if it is damaged.

2. Product description

2.1 Package includes

2.2 Components required for operation

• Battery-operated clipping machine Econom CL/Econom CL Equipe/

Econom CL Fitter

•Charger

• Mains power cord (with device plug)

• Li-ion battery

2.3 Intended use

Battery-operated clipping machine Econom CL/Econom CL Equipe/

Econom CL Fitter

The battery-operated clipping machine Econom CL/Econom CL Equipe/

Econom CL Fitter is used for clipping large animals such as cattle, horses

and large dogs.

Charger GT803/Li-ion battery GT801

The GT803 charger is used to charge the GT801 lithium ion battery.

DANGER

Risk of death by electric shock!

¾Do not open the product.

¾Connect the product only to a grounded power

supply. Art. no. Designation

GT800

GT810

GT834

Battery-operated clipping machine Econom CL,

Econom CL Equipe or

Econom CL Fitter

GT801 Li-ion battery

GT803 Charger

seeAccessories/Spare

parts

Mains power cord (with device plug)

TA013895 Instructions for use

GT604 Hand oiler

Econom CL/Econom CL Equipe/Econom CL Fitter cattle and horse clipping machine

Aesculap®

2.4 Operating principle

Battery-operated clipping machine Econom CL/Econom CL Equipe/

Econom CL Fitter

The battery-operated clipping machine Econom CL/Econom CL Equipe/

Econom CL Fitter is switched on and off using the on/off button 36.

Note

The on/off button only reacts after >0.5 s in order to avoid the machine

being switched on or off unintentionally.

Charger GT803/Li-ion battery GT801

The charger GT803 is designed for a mains voltage/frequency range of

100 V to 240 V and 50 Hz to 60 Hz.

To make the charger GT803 ready for operation, connect it to mains power

by plugging in the mains plug.

The charger GT803 is equipped with one charging bay.

Charging starts automatically as soon as the Li-ion battery is inserted in

the charging station.

The charging time depends on the charge state and capacity of the Li-ion

battery.

Charging principle

The Li-ion batteries are charged by constant current pulses.

The charge state of the Li-ion battery is monitored during charging.

Monitoring of the charging curve ensures that the battery is fully charged

without overcharging.

Additionally, the battery temperature and charging time are monitored as

well.

The charge status display dof the lithium ion battery has 5 LEDs. Each LED

stands for 20 % of charge volume. When the battery is charging, the LED

of the respective charging status blinks. When all the LEDs are

permanently illuminated, the battery is completely charged.

Charging time

Charging is stopped as soon as the maximum charging time is reached. The

charging time is approx. 70 min.

3. Preparation

Non-compliance with the following rules will result in complete exclusion

of liability on the part of Aesculap.

¾Always observe the following guidelines when setting up and

operating the product:

– national regulations for installation and operation,

– the national regulations on fire and explosion protection,

– operating advisories according to IEC-/VDE regulations.

4. Working with the battery-operated

clipping machine, charger and lithium

ion battery

4.1 System set-up

Connecting the accessories

Combinations of accessories that are not mentioned in the present

instructions for use may only be employed if they are specifically intended

for the respective application, and if they do not compromise the

performance and safety characteristics of the products.

4.2 Function check

Battery-operated clipping machine Econom CL/Econom CL Equipe/

Econom CL Fitter

¾Carry out a visual inspection.

¾Ensure that the airfilter 37/38 is positioned correctly, see Fig. G.

¾Push the lithium ion battery 39 into the machine shaft and lock it.

¾Check if the battery is charged-up: Press button e, see Fig. F.

¾The charge status display dindicates the charge status.

Note

In order to prevent the lithium iron battery discharging when the machine

is not being used, the electronic connection between the lithium ion

battery and the control system for the battery-operated clipping machine

is cut after 1 hour.

¾Reactivating the lithium ion battery 39: Press button e, see Fig. F.

All the LEDs in the charge status display dilluminate.

Charger/Li-ion battery

¾Carry out a visual inspection.

¾Prior to connecting the product to mains power:

–Check the mains power cord for any damage.

–Check the product for any damage (e.g. bent contacts of the charging

bay).

¾Plug in mains power cord at the device socket of the charging station.

¾Plug in the mains plug at the mains power socket.

¾Place the lithium lithium iron battery 39 in the charging bay of the

charger and charge it, see Fig. F.

4.3 Connecting the charger/Charging the Li-ion battery

Note

The charger can be used by children if 8 years or older, as well as by persons

with reduced physical, sensory or mental capacities or with lack of

experience and knowledge, if these persons are supervised or have been

instructed on how to use the device safely, and if they understand the risks

associated with the use of the device.

¾Do not allow children to play with the device.

¾Do not allow children to clean or maintain the device without

supervision.

Note

The Li-ion battery heats up slightly during charging.

Note

Disconnect the mains power cord at the mains socket when the charger is

not going to be used.

¾Only use the Aesculap GT803 charger for charging the lithium ion

batteries.

¾To connect charger 40: Plug the device plug of the mains power cord

into the charger.

¾Plug in the mains plug of mains power cord at the mains power socket.

¾Plug the lithium iron battery 39 into the charging bay of the charger

and charge it, see Fig. F.

The LEDs in the charge status display dof the lithium ion battery blink

in accordance with the current charge status. When all the LEDs are

permanently illuminated, the battery is completely charged.

4.4 Change the Li-ion battery

¾Hold the battery-operated clipping machine gwith the cutter head

downwards so that the lithium ion battery 39 does not fall down when

loosened, see Fig. 1.

¾Loosen the battery lock fwith your thumb.

Fig. 1

WARNING

Fire hazard due to battery poles shorted by fluids

or metal components!

¾Li-ion battery not inserted

WARNING

Risk of injury due to damaged mains power cord!

¾Check mains power cord for any damage before

charging.

¾Arrange for any damaged mains power cord to

be replaced by the manufacturer.

WARNING

Risk of injury and material damage due to

damaged Li-ion battery!

¾Prior to charging, check the Li-ion battery for

any damage.

¾Do not use or charge any damaged Li-ion

batteries.

CAUTION

Loss of capacity/performance due to prolonged

storage of the discharged Li-ion battery!

¾Store Li-ion batteries only in fully charged

condition and recharge stored batteries once

every month.

CAUTION

Destruction of the product, charging bay or Li-ion

battery when inserting the wrong type of battery

in the charging bay!

¾Insert Li-ion battery only in the appropriate

charging bay.

Econom CL/Econom CL Equipe/Econom CL Fitter cattle and horse clipping machine

Aesculap®

¾Remove the lithium ion battery 39, and push the charged replacement

lithium ion battery GT801 into the battery-operated clipping

machine g, see Fig. 2.

Fig. 2

¾Secure the lithium ion battery 39 using the battery lock f, see Fig. 3.

Fig. 3

4.5 Handling the cutter head

Lubricating the cutter head

¾Generously oil the cutter head at the lubrication point abefore

shearing each animal, see Fig. A.

¾Oil spring leaves 10 2 to 3 times daily with 3 to 4 drops of oil, see

Fig. C.

Lubricating the gear wheel

¾Unlocking and removing the lithium ion battery 39.

¾Remove both screws 6, see Fig. B.

¾Then turn the cutter head very slightly (about 15°) counterclockwise

and remove it from the motor shell.

¾Apply approximately 1 cm of grease on the two opposite points of the

gear wheel 11, see Fig. C.

¾Carefully place the cutter head on the motor. When re-attaching the

cutter head, ensure that it is turned 15° counterclockwise in such a

way that its lower flange engages with the groove of the motor

housing.

Changing the cutter plate

¾Unlocking and removing the lithium ion battery 39.

¾Loosen the locking cap 3and adjusting screw 4by approx. 2 turns, see

Fig. A.

¾Loosen both clamp screws 9, pull off the cutter plate 1forwards and

remove the upper cutter plate 2, see Fig. D and Fig. E.

¾Before inserting the upper cutter plate 2, ensure that the oscillating

block 8is in the intended recess of the oscillator 7, see Fig. E.

¾Insert the upper cutter plate 2. When doing so, ensure that both tips b

of the oscillator 7engage precisely in the holes cof the upper cutter

plate 2, see Fig. D.

CAUTION

Damage to the clipping machine or the cutter

head due to incorrect lubrication!

¾Only oil the cutter head when the machine is

running.

¾Never immerse the cutter head in liquid of any

kind!

¾Only use GT604 light lubricating oil.

CAUTION

Damage to the clipping machine or the gear wheel

due to incorrect lubrication!

¾Use only gear grease GT605.

¾Lubricate the gear wheel 1 to 2 times during

the shearing season.

¾Push the lower cutter plate 1below the heads of the clamping

screws 9all the way on to the cutter head shell and screw both

clamping screws 9tight.

¾Tighten the adjusting screw 4until both cutter plates are pressing

slightly against one another, see Fig. A.

Adjusting the plate pressure

Note

The plate pressure must be set with the machine running and without

auxiliary tools.

Note

If the plate pressure is too high, this results in the build-up of heat and

greater wear to the cutter plates.

¾Carefully loosen the locking cap 3and adjusting screw 4until the

upper cutter plate 2is no longer pressing against the lower cutter

plate 1(the sound of the motor becomes noticeably higher-pitched),

see Fig. A.

¾Screw in the adjusting screw 4until you feel slight resistance. From

this point, keep turning approximately one full sun and then tightened

the locking cap 3.

Cleaning the cutter head

¾The cutter head must be cleaned at least after each day of clipping

time or if it gets dirty.

¾Unlocking and removing the lithium ion battery 39.

¾Remove both screws 6, see Fig. B.

¾Then turn the cutter head very slightly (about 15°) counterclockwise

and remove it from the motor shell.

¾Remove the cutter plates, see Changing the cutter plate.

¾Thoroughly clean the interior part and individual parts of the cutter

head using a brush.

¾Insert the cutter plate and tighten, see Changing the cutter plate.

¾Lubricate the gear wheel, see Lubricating the gear wheel.

¾Carefully place the cutter head on the motor. When re-attaching the

cutter head, ensure that it is turned 15° counterclockwise in such a

way that its lower flange engages with the groove of the motor

housing.

¾Lubricate the cutter head, see Lubricating the cutter head.

Cleaning the air filter

¾Clean the airfilter 37/38 at least once per day or if it gets dirty.

¾Remove the airfilter 37/38 from the battery-operated clipping

machine, see Fig. G.

¾Thoroughly clean the airfilter 37/38 in warm water with a brush.

¾Leave the airfilter 37/38 to dry.

¾Clean the battery-operated clipping machine.

¾Place the airfilter 37/38 on the battery-operated clipping machine.

Re-sharpen the cutter plates.

¾In order to re-sharpen the cutter plates, contact Technical Service, see

Technical Service.

4.6 Storage

¾Clean the clipping machine and cutter plates thoroughly before

storing, see Reprocessing.

¾Store the clipping machine in a dry, dark and clean room.

5. Cutter plates

5.1 Cutter plates compatible with cutter head GT367

5.2 Recommended combinations

Art. no. Designation

GT501 Upper cutter plate with 15 cutting teeth

GT502 Lower cutter plate with 31 cutting teeth,

Cutting height: 3 mm

GT503 Upper cutter plate with 17 cutting teeth

GT504 Lower cutter plate with 18 cutting teeth,

Cutting height: 3 mm

GT505 Upper cutter plate with 23 cutting teeth

GT506 Lower cutter plate with 23 cutting teeth,

Cutting height: 3 mm

GT508 Lower cutter plate with 51 cutting teeth,

Cutting height: 1 mm

GT510 as GT506, but a cutting height of 5 mm

GT511 as GT502, but a cutting height of 1 mm

Combination Upper/lower plate Suitable for

closely spaced

teeth

GT501/GT502 Cattle and horses (regular

equipment for GT474 and

GT367)

GT501/GT511 Industrial shearing

GT505/GT508 (e.g. coat shearing)

medium spaced

teeth

GT505/GT506 Cattle, dogs and goats

GT505/GT510 Dogs and goats

widely spaced

teeth

GT503/GT504 Cattle, sheep with fine wool

and single sheep

Econom CL/Econom CL Equipe/Econom CL Fitter cattle and horse clipping machine

Aesculap®

6. Reprocessing

6.1 Cleaning/disinfection

¾Wipe the shell of the product with a lint-free cloth moistened with a

commercial disinfectant for wipe disinfection.

¾If necessary, after the appropriate exposure time, wipe off any residues

of the cleaning/disinfecting agent with a lint-free cloth moistened

with clean water.

¾Dry the product with a clean, lint-free cloth.

¾Clean the contacts in the charging bay with isopropanol or ethyl

alcohol and a cotton swab. Do not use corrosive chemicals.

¾If necessary, repeat the cleaning/disinfecting process.

6.2 Inspection and checking

¾Allow the product to cool down to room temperature.

¾Inspect the product after each cleaning and disinfecting cycle to be

sure it is: clean, functional, and undamaged.

¾Check the product for any damage, abnormal running noise,

overheating or excessive vibration.

¾Inspect the shearing head for broken, damaged or blunt cutting edges.

¾Set aside the product if it is damaged.

7. Maintenance

To ensure reliable operation, Aesculap recommends servicing the product

at least once a year.

DANGER

Risk of electric shock and fire hazard!

¾Before cleaning:

–Remove the mains plug from the charger.

–Unlock the lithium ion battery and remove

from the battery-operated clipping machine.

¾Do not use flammable or explosive cleaning or

disinfecting solutions.

¾Ensure that no fluids will penetrate the

product.

CAUTION

Damage to, or destruction of the product caused

by mechanical cleaning/disinfection!

¾Only clean and disinfect the product manually.

¾Do not sterilize the product under any

circumstances.

CAUTION

Risk of damage to the product due to

inappropriate cleaning/disinfecting agents!

¾Only use cleaning/disinfecting agents approved

for surface cleaning. Follow the manufacturer’s

instructions for the respective cleaning/

disinfecting agent.

¾Never immerse the product in water or

detergent.

¾Do not introduce any fluid into the charging

bays.

¾Clean the contacts in the charging bay,

applying extreme care.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Herramientas eléctricas de Aesculap

Aesculap

Aesculap Favorita II Manual de usuario

Aesculap

Aesculap GT205 Manual de usuario

Aesculap

Aesculap GT369 Manual de usuario

Aesculap

Aesculap GT474 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual