Aeronix GES Manual de usuario

1775 West Hibiscus Blvd, Suite 200

Melbourne, FL 32901

(321) 984-1671

www.Aeronix.com

Gigabit Ethernet Switch (GES)

User’s Manual

GES – Users Manual

Page ii

Document Revision History

Ver/Rev

Description of Change

Chg’d By

Chg/Rel #

Date

-001/- Initial Release of User’s Manual for the

GEN2GES R. Little SP-619 10 October 2011

-001/A Added Section 12 – Performance Parameters R. Kneapler SP-640 9 December 2011

-001/B Update Section 9 to reflect updated mounting

hardware R. Kneapler SP-705 2 July 2012

-001/C

Fixed word order issue with Summary Status

packet in (Sect 7.3.2), and corrected the unit

weight on pages 29 & 31

R. Little SP-725 6 September 2012

-001/D Added COG dimensioning to GES Chassis

Drawing in Section 9. S. Ammerman SP-738 19 October 2012

-001/E Updated Qualification Test Table (see page

30) S. Ammerman SP-814 16 September 2013

Note:

This manual applies to the Aeronix

AE101264-002

12-Port Gigabit Ethernet Switch

This User’s Manual is Part Number AE301016-001

GES – Users Manual

Page iii

Table of Contents

1. OVERVIEW ..........................................................................................................1

2. BLOCK DIAGRAM ...............................................................................................1

3. ELECTRICAL CONNECTIONS............................................................................2

3.1. J1 CONNECTOR...................................................................................................2

3.2. J2 CONNECTOR...................................................................................................2

3.3. TABLE 3-1: CONNECTOR PIN-OUTS .......................................................................3

3.4. INTERFACE PORT DETAILS....................................................................................4

3.4.1. Ethernet Ports ............................................................................................4

3.4.2. Serial and Programming Ports ...................................................................4

3.4.3. Management Processor .............................................................................4

3.4.4. Input Power................................................................................................5

4. PORT DETAILS....................................................................................................6

4.1. ETHERNET PORT MAPPING...................................................................................6

4.2. SERIAL PORTS.....................................................................................................6

5. BOOTLOADER ....................................................................................................7

6. MENU INTERFACE..............................................................................................8

6.1. REQUIRED HARDWARE .........................................................................................8

6.2. SERIAL PORT SETUP............................................................................................8

6.3. MENUS ...............................................................................................................8

6.3.1. How the menus work..................................................................................8

6.3.2. Menu Header .............................................................................................8

6.3.3. Main Menu .................................................................................................9

6.3.4. Configuration Menu..................................................................................10

6.4. EXAMPLE ..........................................................................................................12

7. MANAGEMENT PROCESSOR ETHERNET COMMUNICATIONS ...................15

7.1. NETWORK COMMUNICATIONS SUPPORTED...........................................................15

7.2. GENERAL FORMAT OF A GES UDP PACKET ........................................................15

7.3. UDP PACKETS ACCEPTED/PRODUCED WHILE GES APPLICATION IS ACTIVE ..........16

7.3.1. GES Status Command (Opcode: 0) .........................................................16

7.3.2. GES Summary Status (Opcode 1) ...........................................................17

7.3.3. GES Initiated BIT Status (Opcode 2) .......................................................18

7.3.4. GES Operational Status (Opcode 4) ........................................................20

7.3.5. GES Performance Status (Opcode 5) ......................................................21

7.3.6. GES Programming Command (Opcode 3)...............................................22

7.3.7. GES Programming Response (Opcode 6) ...............................................23

7.3.8. GES Reboot .............................................................................................24

7.3.9. GES Reboot Acknowledge.......................................................................24

7.3.10. Opcode Unrecognized By Application......................................................24

GES – Users Manual

Page iv

7.4. UDP PACKETS ACCEPTED/PRODUCED WHILE BOOTLOADER IS ACTIVE .................24

7.4.1. Opcode Unrecognized By Bootloader ......................................................24

7.4.2. Erase Non-Boot-Bank (NBB) Flash..........................................................25

7.4.3. Erase NBB Flash Acknowledge ...............................................................25

7.4.4. Erase NBB Flash Completed ...................................................................25

7.4.5. Program NBB Data ..................................................................................26

7.4.6. Program NBB Data Acknowledge ............................................................26

7.4.7. Program NBB Data Completed ................................................................26

7.4.8. Finished Programming .............................................................................27

7.4.9. Finished Programming Acknowledge.......................................................27

7.4.10. Bad CRC..................................................................................................27

8. SWITCH MANAGEMENT CAPABILITIES.........................................................28

9. HARDWARE MOUNTING ..................................................................................29

10. INDICATORS .....................................................................................................29

11. QUALIFICATIONS .............................................................................................30

12. PERFORMANCE PARAMETERS......................................................................31

13. WARRANTY .......................................................................................................31

14. ERRATA.............................................................................................................31

14.1. COMMUNICATIONS WITH THE GES MANAGEMENT PROCESSOR .............................31

15. PRODUCTS AND SERVICES............................................................................33

Aeronix places no restriction on the duplication or distribution of this document;

however, it must remain unaltered and in its entirety.

GES – Users Manual

Page 1 of 33

1. Overview

Designed and produced by Aeronix, Inc. of Melbourne, Florida, the Gigabit Ethernet

Switch (GES) is designed for use in hostile environments.

The GES is a lightly managed switch with twelve 10/100/1000BaseT Ethernet ports, and

two RS-232 management ports. Its rugged monolithic design is intended to operate in

severe environments without the need for forced air cooling.

This document is intended to provide the information required to interface with the

Aeronix Gigabit Ethernet Switch (GES) hardware.

The part number of the Aeronix 12-Port Gigabit Ethernet Switch is AE101264-002.

2. Block Diagram

The basic functional blocks within the GES and their basic interactions are shown in

Figure 2-1.

Figure 2-1: GES Block Diagram

GES – Users Manual

Page 2 of 33

3. Electrical Connections

The GES has two electrical connectors, J1 and J2.

3.1. J1 Connector

J1 is a 100 pin M38999 Series II connector, Part Number MS27508E22B35P.

An example mating cable connector for J1 is Part Number MS27473E22B35S.

J1 contains the following electrical interfaces:

•Six Ethernet Ports (0 – 5)

•Two RS-232 Serial Ports

oDEV1 – Dedicated Maintenance Port for the Management Processor

oDEV2 – Designed to be programmed as an Ethernet to Serial Bridge

3.2. J2 Connector

J2 is a 100 pin M38999 Series II connector Part Number MS27508E22B35PA.

An example mating cable connector for J2 is Part Number MS27473E22B35SA.

J2 contains the following electrical interfaces:

•Six Ethernet Ports (6 – 11)

•Input Power (nominal 28 VDC per MIL-STD-704A)

GES – Users Manual

Page 3 of 33

3.3. Table 3-1: Connector Pin-outs

J1 J2

Signal

Chassis Ground

Port 0 - A(+)

Chassis Ground

Port 6 - A(+)

Chassis Ground

Port 0 - C(-)

Port 3 - A(+)

Port 6 - C(-)

Port 9 - A(+)

Port 0 - D(+)

Port 3 - C(+)

Port 6 - D(+)

Port 9 - C(+)

Port 0 - D(-)

Port 3 - D(-)

Port 6 - D(-)

Port 9 - D(-)

Chassis Ground

RX_FROM_DEV1

Chassis Ground

28VRTN

Port 1 - A(+)

TX_TO_DEV1

Port 7 - A(+)

28VRTN

Chassis Ground

Port 2 - B(+)

Chassis Ground

Port 8 - B(+)

Port 0 - A(-)

Port 2 - C(-)

Port 6 - A(-)

Port 8 - C(-)

Port 0 - C(+)

Port 2 - D(+)

Port 6 - C(+)

Port 8 - D(+)

Chassis Ground

Port 1 - A(-)

Port 3 - A(-)

Port 7 - A(-)

Port 9 - A(-)

Port 1 - C(+)

Chassis Ground

Port 7 - C(+)

Chassis Ground

Port 1 - D(-)

Chassis Ground

Port 7 - D(-)

Chassis Ground

Reserved

Chassis Ground

28V

Chassis Ground

RX_FROM_DEV2

Chassis Ground

28VRTN

Chassis Ground

TX_TO_DEV2

Chassis Ground

Reserved

Port 0 - B(+)

Chassis Ground

Port 6 - B(+)

Chassis Ground

Port 1 - B(+)

Port 2 - C(+)

Port 7 - B(+)

Port 8 - C(+)

Port 1 - B(-)

Port 2 - D(-)

Port 7 - B(-)

Port 8 - D(-)

Port 1 - C(-)

Chassis Ground

Port 7 - C(-)

Chassis Ground

Port 1 - D(+)

Chassis Ground

Port 7 - D(+)

Chassis Ground

Reserved

Port 5 - D(-)

28V

Port 11 - D(-)

GND

Port 5 - D(+)

Reserved

Port 11 - D(+)

Reserved

GND

Chassis Ground

28VRTN

Port 0 - B(-)

Chassis Ground

Port 6 - B(-)

Chassis Ground

Port 4 - A(+)

Chassis Ground

Port 10 - A(+)

Chassis Ground

Port 5 - A(+)

Chassis Ground

Port 11 - A(+)

Chassis Ground

Port 5 - C(+)

Chassis Ground

Port 11 - C(+)

Reserved

Port 5 - C(-)

28V

Port 11 - C(-)

Reserved

Chassis Ground

28V

Chassis Ground

Port 4 - A(-)

Chassis Ground

Port 10 - A(-)

Chassis Ground

Port 4 - D(-)

Chassis Ground

Port 10 - D(-)

Port 2 - A(+)

Port 4 - D(+)

Port 8 - A(+)

Port 10 - D(+)

Chassis Ground

Port 3 - B(+)

Port 5 - A(-)

Port 9 - B(+)

Port 11 - A(-)

Port 3 - B(-)

Port 5 - B(+)

Port 9 - B(-)

Port 11 - B(+)

Port 3 - C(-)

Chassis Ground

Port 9 - C(-)

Chassis Ground

Port 3 - D(+)

Port 4 - B(+)

Port 9 - D(+)

Port 10 - B(+)

Reserved

Port 4 - B(-)

Reserved

Port 10 - B(-)

GND

Port 4 - C(+)

Reserved

Port 10 - C(+)

Chassis Ground

Port 4 - C(-)

Chassis Ground

Port 10 - C(-)

Port 2 - B(-)

Chassis Ground

Port 8 - B(-)

Chassis Ground

50 Port 2 - A(-) 100 Port 5 - B(-) 50 Port 8 - A(-) 100 Port 11 - B(-)

GES – Users Manual

Page 4 of 33

3.4. Interface Port Details

3.4.1. Ethernet Ports

All connections in Table 3-1 that have a white background are Ethernet Port

connections.

Table 3-2 indicates the appropriate wiring connections for the GES Ethernet ports

relative to the available link speeds. Please note that MDI is the preferred connection

choice. The GES and most modern Ethernet enabled electronics are capable of

connecting using the MDIX scheme, but it is not advised.

Table 3-2: Ethernet Port Connections

GES Pin RJ-45

Pinout P/N

MDI

MDIX

1000Base-T

100Base-T

10-Base-T

1000Base-T

100Base-T

10-Base-T

Port X - A(+/-)

1/2

BI_DA+-

TX+-

BI_DA+-

RX+-

Port X - B(+/-)

3/6

BI_DB+-

RX+-

BI_DB+-

TX+-

Port X - C(+/-)

4/5

BI_DC+-

Unused

BI_DC+-

Unused

Port X - D(+/-)

7/8

BI_DD+-

Unused

BI_DD+-

Unused

3.4.2. Serial and Programming Ports

All connections in Table 3-1 that have an Orange background are Serial Port

connections.

The DEV1 serial port is a dedicated GES Management Processor Maintenance Port.

The DEV2 serial port was designed for future expansion as an in-band Ethernet to Serial

Bridge.

Table 3-3 indicates the appropriate wiring connections for the DEV1 and DEV2 serial

ports.

Table 3-3: Serial Port Connections

Signal

Direction

Type

Connects

Notes

TX_TO_DEVX

Output

RS-232

DB9-2

RX_FROM_DEVX

Input

RS-232

DB9-3

GND

Reference

RTN

DB9-5

J1-26,77

3.4.3. Management Processor

The GES provides an ARM 9 processor running at 96MHz for both internal and customer

specified functions. This processor is in-band allowing control by any device on the

Ethernet network that is connected to the GES.

This processor is lightly loaded after initialization of the GES allowing customer specified

functions to use most of the available processing power if required.

GES – Users Manual

Page 5 of 33

The primary purpose of this processor is to:

•Initialize the Ethernet Switch IC for GES default operation

•PBIT and CBIT

•Customer specific functions if required

3.4.4. Input Power

The connections shown in Table 3-1 with a Red background are Power Connections.

The input power requirements are as specified in MIL-STD-704A:

Aircraft, 28 VDC, Category B (curves 2 &3 of Fig. 9)

During normal operations the average power consumption with all 12 ports connected at

1 GB speed is 17 watts. Input current is internally limited to 2 amps.

GES – Users Manual

Page 6 of 33

4. Port Details

4.1. Ethernet Port Mapping

In its factory default configuration, all twelve Ethernet ports of the GES are configured

identically. When programming custom configurations into the GES, the External-Port

numbers map to the Switch’s MAC and Phy Port numbers as defined in Table 4-1.

Table 4-1 Ethernet Port Mapping

External Port

MAC Port

Phy Port

Port 0

Port 1

Port 2

Port 3

Port 4

Port 5

Port 6

Port 7

Port 8

Port 9

Port 10

Port 11

GES Internal

Management CPU CPU Port n/a

4.2. Serial Ports

There are two serial ports associated with the Management Processor, DEV1 and DEV2.

Both ports are RS-232 compatible and operate only at:

•115.2K baud

•1 Stop Bit

•No Parity

•No Flow Control

The DEV1 port supports out-of-band configuration management of the GES.

The DEV2 serial port is available for customer specific uses. Contact Aeronix if you

would like custom programming for this port such as an Ethernet to Serial bridge or

sensor/actuator to Ethernet.See section 6.2 for current details.

Tabla de contenidos

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario