AERMEC MODUCONTROL Manual de usuario
SUMMARIZED USER MANUAL
WATER
CHILLER
MODUCONTROL
CHILLERS
REVERSIBLE HEAT PUMPS
CONDENSING UNITS
• EXTERNAL UNITS
• HIGH EFFICIENCY
• HOT WATER PRODUCTION
UP TO 50ºC
READINGMENU•USERMENU•ERRORMENU
EN
READINGS MENU
Reading menu
The reading menu gives the user the option to read all parameters
Lista indici e relative letture MENÚ LETTURE (nessuna password)
Index - String Meaning of the reading
Water output temperature
Water input temperature
Coil temperature
Force gas temperature
Outside air temperature
Delivery pressure
Suction pressure
Thermostat
CP times
Hours of operation (thousands)
Hours of operation (units)
Compressor pickup current
(thousands)
Index - String Meaning of the reading
Compressor pickup current (units)
Software release
Minor software releases
Setting currently in use
DCP pressure setting
Operating hours
COMPRESSOR 2 (thousands)
Operating hours
COMPRESSOR 2 (units)
Compressor pickup current
COMPRESSOR 2 (thousands)
Compressor pickup current
COMPRESSOR 2 (units)
Power fraction
Required frequency (INVERTER)
Pressure drop
Parameters only visible in heat pump models
Parameters only visible in models set for hot domestic
water production
Parameters only visible in the models with DCP installed
Parametes only visible in bicompressor models
Parameters only visible in the models with inverter
compressor
USER MENU
User menu
The user menu gives the user the option to change settings
1. press the srewdriver symbol
2. 000 apears
3. Press the srewdriver again
4. Use up and down keys to nd a setting
5. Press the screwdriver again (blinking of index nr)
6. Change the setting with up and down keys
7. Conrm with screwdriver
For Opticlimate set:
1 STF on 26°C
2 BNF on 1°C
-
- -
SF1: index (6) user menu;
SF2: index (8) user menu;
TF1: index (7) user menu;
TF2: index (9) user menu;
In cooling mode, the work setting is calculated au-
tomatically on the basis of the outside temperature,
following the logic highlighted in the diagram.
SC1: index (A) user menu;
SC2: index (C) user menu;
TC1: index (B) user menu;
TC2: index (d) user menu;
In heating mode, the work setting is calculated au-
tomatically on the basis of the outside temperature,
following the logic highlighted in the diagram.
USER MENU
-
-
USER MENU
-
-
rature (depending on the type of control set by parameter (0) in the installer menu) is less than the hot
Lista indici e relative letture MENÚ LETTURE (nessuna password)
Index - String Meaning of the reading
Water output temperature
Water input temperature
Coil temperature
Force gas temperature
Outside air temperature
Delivery pressure
Suction pressure
Thermostat
CP times
Hours of operation (thousands)
Hours of operation (units)
Compressor pickup current
(thousands)
Index - String Meaning of the reading
Compressor pickup current (units)
Software release
Minor software releases
Setting currently in use
DCP pressure setting
Operating hours
COMPRESSOR 2 (thousands)
Operating hours
COMPRESSOR 2 (units)
Compressor pickup current
COMPRESSOR 2 (thousands)
Compressor pickup current
COMPRESSOR 2 (units)
Power fraction
Required frequency (INVERTER)
Pressure drop
Parameters only visible in heat pump models
Parameters only visible in models set for hot domestic
water production
Parameters only visible in the models with DCP installed
Parametes only visible in bicompressor models
Parameters only visible in the models with inverter
compressor
USER MENU
ERROR MENU
Error
An error can be reset by switching the main power of the unit off for 5 seconds.
When there is air trapped inside the system E104 will appear. Bleed the system and switch the power off to reset.
After rst time operation E104 will appear several times until all air is out.
We advise to use automatic bleeders at the highest point of the water-system.
-
-
-
-
-
Notes
-
-
-
-
-
-
-
-
-
122
ERROR MENU
--
-
--
-
ERROR MENU
Otros manuales para MODUCONTROL
2
Tabla de contenidos
Otros manuales de Unidad de control de AERMEC
AERMEC
AERMEC VHL22 Manual de usuario
AERMEC
AERMEC RTE240 Manual de usuario
AERMEC
AERMEC WMT 10 Especificaciones técnicas
AERMEC
AERMEC VMF-E5 Manual de usuario
AERMEC
AERMEC VCZ41 Manual de usuario
AERMEC
AERMEC VCFD 1 Manual de usuario
AERMEC
AERMEC MCR Manual de usuario
AERMEC
AERMEC MODUCONTROL Manual de lista de piezas
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
