AEI Security & Communications DigiSender ZX7 Manual de usuario
WATCH A VIDEO
INSTALLATION
& TROUBLESHOOTING GUIDE
Available online at: www.aei.eu/video
WATCH A VIDEO
INSTALLATION
& TROUBLESHOOTING GUIDE
Available online at: www.aei.eu/video
121009-1
DigiSender ZX7
MODEL: DG458
5.8GHz Quad Input Wireless AV Sender
®
PLEASE KEEP THIS I STRUCTIO MA UAL FOR FUTURE REFERE CE
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender
Please read this instruction manual carefully prior to installationPage 02
Table of Contents
Introduction 03
STEP 1 - Unpack your DigiSender® ZX7 04
STEP 2 - Install the DigiSender® ZX7 Transmitter 05-06
STEP 3 - Install the I Systeme Technik™ 07
STEP 4 - Install the DigiSender® ZX7 eceiver 08
STEP 5 - Using the DigiSender® ZX7 09-12
The DigiSender® Remote Control 10
DigiSender® ZX7 Basic Functions 11
DigiSender® ZX7 Advanced Function 12
Upgrades and Accessories 13
Troubleshooting 14-17
Picture Problems 14-15
Audio Problems 16
Problems Controlling Your Source Equipment 17
Technical Support 18
Document of Conformity 19
WAR I G
To prevent damage do not
expose this unit to rain or
moisture.
Please read this instruction manual carefully prior to installation Page 03
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender
Introduction
Congratulations on purchasing the DigiSender® ZX7 - Quad Input 5.8GHz Wireless AV Sender. This
product represents state of the art wireless audio and video technology and the most advanced
Infra-Red relay technology at exceptional value for money.
You can now enjoy DVD quality video and Hi-Fi stereo sound from your Satellite, Cable, Freeview,
DVD or VCR in another room in your home.
The DigiSender® ZX7 is a quad input wireless AV sender with a difference. Because it uses 5.8GHz
to transmit rather than the much more common 2.4GHz, you can use the DigiSender® ZX7 without
the worry of interference from wireless routers, Bluetooth devices and other wireless products. It
also incorporates our advanced DigiEye™ remote relay technology allowing flawless operation with
every set top box ever made.
Bene it rom 5.8GHz transmission, 4 Inputs, 4 Audio/Video Channels, 16 Remote Relay
Channels and unsurpassed compatibility with the new DigiSender® ZX7!
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender
Please read this instruction manual carefully prior to installationPage 04
STEP 1 - Unpack your DigiSender® ZX7
All DigiSender® orders are computer weight checked when packed. However, it is a good idea to
check all kit contents are present before proceeding with the installation.
POWER
1234
RECEIVER
POWER
1234
TRANSMITTER
Receiver
Transmitter
2 x Power Supply
IR Systeme Technik™
POWER
Input 1
DigiConnector™ 1
Input 2
DigiConnector™ 2
Input 3
Aux 1
Input 4
Aux 2
Remote Control
Please read this instruction manual carefully prior to installation Page 05
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender
STEP 2 - Install the DigiSender® ZX7 Transmitter
Ensure that the Audio/Video and emote elay
Channel switches on the back of the Transmitter
are set to 1.
3.
Connect DigiConnector™ 1 to your Satellite,
Cable or Freeview box. Use the SCART socket
labelled ‘TV’ or ‘OUT’. Connect any existing
SCART lead into the rear of the DigiConnector™.
1.
Connect DigiConnector™ 2 to your DVD Player,
HDD ecorder or VC . Use the SCART socket
labelled ‘TV’ or ‘OUT’. Connect any existing
SCART lead into the rear of the DigiConnector™.
2.
The Transmitter will send the audio and video from up to four connected sources (your Satellite and
DVD Player for example) to the Receiver, located in another room in your home.
Connect the I Emitter to the socket labelled ‘I ’
on the back of the Transmitter. See Page 07 for
more information on installing the IR Systeme
Technik™.
4.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender
Please read this instruction manual carefully prior to installationPage 06
continued...
Connect the Power Supply Unit (PSU) to the
socket labelled ‘PSU’ on the rear of the
Transmitter.
5.
Connect the Power Supply Unit (PSU) to an
available mains socket and switch on at the back
of the Transmitter.
6.
What’s the A/B switch for??
The Contrast (A/B) switch is present to compen-
sate for differences in equipment set-ups.
Once installation is
complete, if you
experience a poor
picture try
adjusting the
A/B setting.
Note: Try to avoid positioning the Transmitter directly on top of other electrical devices as this could lead
to a poor picture.
Please read this instruction manual carefully prior to installation Page 07
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender
STEP 3 - Install the IR Systeme Technik™
Once set up correctly, the IR Systeme Technik™ will enable you to control your source equipment
from the receiving location in your home.
Because everyone’s set up is different there are many ways you can install the IR Systeme Technik™
and the various included accessories will help you in setting it up correctly.
Mount the I Emitter vertically using acces-
sories 1 and 2. Ensure the ED is facing the
remote control pick up point on your source
equipment.
Mount the I Emitter horizontally using the sup-
plied sticky pad. Ensure the ED is facing the
remote control pick up point on your source
equipment.
Example 1 Example 2
Accessory #1 Extension Pieces
Accessory #2
IR Emitter
Ensure that the Audio/Video and emote elay
Channel switches on the back of the eceiver
are set to 1.
2.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender
Please read this instruction manual carefully prior to installationPage 08
STEP 4 - Install the DigiSender® ZX7 Receiver
The Receiver will pick up the signals being sent by your Transmitter and output them to a connect-
ed TV.
Connect the Power Supply Unit (PSU) to the
socket labelled ‘PSU’ on the eceiver.
3.
Locate a vacant SCA T socket on the back of
your receiving TV and insert the DigiSender®
SCA T cable.
1.
Connect the Power Supply Unit (PSU) to an
available mains socket and switch on at the back
of the eceiver.
4.
Please read this instruction manual carefully prior to installation Page 09
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender
STEP 5 - Using the DigiSender® ZX7
Switch on the source equipment (Satellite,
Freeview, DVD, VCR, etc.).
1.
POWER
POWER
Turn on the Transmitter and eceiver by pushing
the Power button on the front of the units. The
standby ED will change from red to green to indi-
cate the unit is switched on. Alternatively press the
Power button on the DigiSender® Remote Control.
2.
On the receiving TV, select the SCA T channel
assigned to the SCA T socket that you plugged
the DG458 eceiver in to. This may be labelled as
SCART, AU , AV, VIDEO, VCR or .
4.
1234
TRANS
Select Input 1 by pressing the Power button
again on the Transmitter and eceiver. The
green Input ED will light to indicate which
source is active.Alternatively press the ‘Input 1’ but-
ton on the DigiSender® Remote Control at the trans-
mitting location.
3.
1. POWE
The POWE button will turn your DigiSender®
ZX7 Transmitter or Receiver On or Off.
2. Input 1
The Input 1 button will select Input 1 on the
Transmitter and Receiver. Input 1 will be what
ever source equipment is connected to
DigiConnector™ 1. For example, a Satellite,
Cable or Freeview box.
3. Input 2
The Input 2 button will select Input 2 on the
Transmitter and Receiver. Input 2 will be what
ever source equipment is connected to
DigiConnector™ 2. For example, a DVD
Player.
4. Input 3
The Input 3 button will select Input 3 on the
Transmitter and Receiver. Input 3 will be what
ever source equipment is connected to the
Aux 1 socket on the Transmitter. For example, a
DVR or VCR.
5. Input 4
The Input 4 button will select Input 4 on the
Transmitter and Receiver. Input 4 will be what
ever source equipment is connected to the
Aux 2 socket on the Transmitter. For example, a
CCTV Camera.
DG458 - DigiSender® ZX7 - 5.8GHz Quad Input Wireless AV Sender
Please read this instruction manual carefully prior to installationPage 10
Using the DigiSender® ZX7
The DigiSender® Remote Control
POWER
Input 1
DigiConnector™ 1
Input 2
DigiConnector™ 2
Input 3
Aux 1
Input 4
Aux 2
1.
2.
3.
4.
5.
Tabla de contenidos
Otros manuales de Receptor de AEI Security & Communications
AEI Security & Communications
AEI Security & Communications DG258 igiSender HQ2 Manual de usuario
AEI Security & Communications
AEI Security & Communications DGXDSDV112 Manual de usuario
AEI Security & Communications
AEI Security & Communications DigiSender X7 DG440 Manual de usuario
AEI Security & Communications
AEI Security & Communications DigiSender HQR DG15RX Manual de usuario
