ADVANTEST R3264 Manual de usuario

MANUAL NUMBER

CPrinted in Japan

ADVANTEST CORPORATION

R3267 Series OPT08

Rx Control Option

Operation Manual

FOE-8370665C00

1999 First printing September 1, 1999

Applicable models

R3264

R3267

R3273

Cover

No. ESF00

Safety-1

Safety Summary

To ensure thorough understanding of all functions and to ensure efficient use of this instrument, please read the

manual carefully before using. Note that Advantest bears absolutely no responsibility for the result of operations

caused due to incorrect or inappropriate use of this instrument.

If the equipment is used in a manner not specified by Advantest, the protection provided by the equipment may

be impaired.

• Warning Labels

Warning labels are applied to Advantest products in locations where specific dangers exist. Pay

careful attention to these labels during handling. Do not remove or tear these labels. If you have

any questions regarding warning labels, please ask your nearest Advantest dealer. Our address

and phone number are listed at the end of this manual.

Symbols of those warning labels are shown below together with their meaning.

DANGER: Indicates an imminently hazardous situation which will result in death or serious

personal injury.

WARNING: Indicates a potentially hazardous situation which will result in death or serious

personal injury.

CAUTION: Indicates a potentially hazardous situation which will result in personal injury or

a damage to property including the product.

• Basic Precautions

Please observe the following precautions to prevent fire, burn, electric shock, and personal inju-

ry.

• Use a power cable rated for the voltage in question. Be sure however to use a power cable

conforming to safety standards of your nation when using a product overseas.

• When inserting the plug into the electrical outlet, first turn the power switch OFF and then

insert the plug as far as it will go.

• When removing the plug from the electrical outlet, first turn the power switch OFF and then

pull it out by gripping the plug. Do not pull on the power cable itself. Make sure your hands

are dry at this time.

• Before turning on the power, be sure to check that the supply voltage matches the voltage

requirements of the instrument.

• Be sure to plug the power cable into an electrical outlet which has a safety ground terminal.

Grounding will be defeated if you use an extension cord which does not include a safety

ground terminal.

• Be sure to use fuses rated for the voltage in question.

• Do not use this instrument with the case open.

• Do not place objects on top of this product. Also, do not place flower pots or other containers

containing liquid such as chemicals near this product.

Safety Summary

Safety-2

• When the product has ventilation outlets, do not stick or drop metal or easily flammable ob-

jects into the ventilation outlets.

• When using the product on a cart, fix it with belts to avoid its drop.

• When connecting the product to peripheral equipment, turn the power off.

• Caution Symbols Used Within this Manual

Symbols indicating items requiring caution which are used in this manual are shown below to-

gether with their meaning.

DANGER: Indicates an item where there is a danger of serious personal injury (death or seri-

ous injury).

WARNING: Indicates an item relating to personal safety or health.

CAUTION: Indicates an item relating to possible damage to the product or instrument or relat-

ing to a restriction on operation.

• Safety Marks on the Product

The following safety marks can be found on Advantest products.

: ATTENTION - Refer to manual.

: Protective ground (earth) terminal.

: DANGER - High voltage.

: CAUTION - Risk of electric shock.

• Replacing Parts with Limited Life

The following parts used in the instrument are main parts with limited life.

Replace the parts listed below after their expected lifespan has expired.

Note that the estimated lifespan for the parts listed below may be shortened by factors such as

the environment where the instrument is stored or used, and how often the instrument is used.

The parts inside are not user-replaceable. For a part replacement, please contact the Advantest

sales office for servicing.

There is a possibility that each product uses different parts with limited life. For more informa-

tion, refer to Chapter 1.

Safety Summary

Safety-3

Main Parts with Limited Life

• Hard Disk Mounted Products

The operational warnings are listed below.

• Do not move, shock and vibrate the product while the power is turned on.

Reading or writing data in the hard disk unit is performed with the memory disk turning at a

high speed. It is a very delicate process.

• Store and operate the products under the following environmental conditions.

An area with no sudden temperature changes.

An area away from shock or vibrations.

An area free from moisture, dirt, or dust.

An area away from magnets or an instrument which generates a magnetic field.

• Make back-ups of important data.

The data stored in the disk may become damaged if the product is mishandled. The hard disc

has a limited life span which depends on the operational conditions. Note that there is no

guarantee for any loss of data.

• Precautions when Disposing of this Instrument

When disposing of harmful substances, be sure dispose of them properly with abiding by the

state-provided law.

Harmful substances: (1) PCB (polycarbon biphenyl)

(2) Mercury

(3) Ni-Cd (nickel cadmium)

(4) Other

Items possessing cyan, organic phosphorous and hexadic chromium

and items which may leak cadmium or arsenic (excluding lead in sol

der).

Example: fluorescent tubes, batteries

Part name Life

Unit power supply 5 years

Fan motor 5 years

Electrolytic capacitor 5 years

LCD display 6 years

LCD backlight 2.5 years

Floppy disk drive 5 years

Environmental Conditions

Safety-4

This instrument should be only be used in an area which satisfies the following conditions:

• An area free from corrosive gas

• An area away from direct sunlight

• A dust-free area

• An area free from vibrations

Figure-1 Environmental Conditions

• Operating position

Figure-2 Operating Position

• Storage position

Figure-3 Storage Position

This instrument can be used safely under the following conditions:

• Altitude of up to 2000 m

• Installation Categories II

• Pollution Degree 2

















Vibration

Direct sunlight

Corrosive

gas

Dust

Front

Keep at least 10 centimeters of space

between the rear panel and any other

surface

Front

This instrument should be stored in a horizontal

position.

When placed in a vertical (upright) position for

storage or transportation, ensure the instrument is

stable and secure.

-Ensure the instrument is stable.

-Pay special attention not to fall.

R3267 Series Option08 Rx Control Option Operation Manual

C-1

TABLE OF CONTENTS

1 OUTLINE OF THE PRODUCT .................................................................. 1-1

1.1 Outline ................................................................................................................. 1-1

2 BEFORE STARTING

..................................................................................... 2-1

2.1 Confirmation of the accessories .......................................................................... 2-1

2.2 How to connect to R3560, R3561 or R3562 ....................................................... 2-2

2.2.1 Connecting the R3267 Series to R3560 ........................................................ 2-2

2.2.2 Connecting the R3267 Series to R3561 or R3562 ........................................ 2-3

2.3 Serial port setting ................................................................................................. 2-4

3 HOW TO OPERATE THE R3560 .............................................................. 3-1

3.1 Outline ................................................................................................................. 3-1

3.2 Reference ............................................................................................................. 3-2

3.2.1 Menu Index ................................................................................................... 3-2

3.2.2 Menu Map ..................................................................................................... 3-3

3.2.3 Functional Description .................................................................................. 3-4

3.3 Example of the measurement (BER measurement) ............................................. 3-18

4 HOW TO OPERATE THE R3561 .............................................................. 4-1

4.1 Outline ................................................................................................................. 4-1

4.2 Reference ............................................................................................................. 4-2

4.2.1 Menu Index ................................................................................................... 4-2

4.2.2 Menu Map ..................................................................................................... 4-4

4.2.3 Functional Description .................................................................................. 4-6

4.2.4 Preset Values ................................................................................................. 4-17

5 HOW TO OPERATE THE R3562 .............................................................. 5-1

5.1 Outline ................................................................................................................. 5-1

5.2 Reference ............................................................................................................. 5-4

5.2.1 Menu Index ................................................................................................... 5-4

5.2.2 Menu Map ..................................................................................................... 5-6

5.2.3 Functional Description .................................................................................. 5-9

5.3 Measurement Example ........................................................................................ 5-27

6 HOW TO OPERATE THE R3562 OPT65 ............................................... 6-1

6.1 Outline ................................................................................................................. 6-1

6.2 Reference ............................................................................................................. 6-3

6.2.1 Menu Index ................................................................................................... 6-3

6.2.2 Menu Map ..................................................................................................... 6-6

6.2.3 Functional Description .................................................................................. 6-11

TABLE OF CONTENTS

R3267 Series Option08 Rx Control Option Operation Manual

Table of Contents

C-2

6.3 Setup Example ..................................................................................................... 6-46

ALPHABETICAL INDEX .................................................................................... I-1

F-1

R3267 Series Option08 Rx Control Option Operation Manual

LIST OF ILLUSTRATIONS

No. Title Page

2-1 Connection between R3267 Series and R3560 (Rear panel) ............................................ 2-2

2-2 Connection between R3267 Series and R3560 (Front panel) ........................................... 2-2

2-3 Connection between R3267 Series and R3561 or R3562 (Rear panel) ............................ 2-3

2-4 Serial port selection screen ............................................................................................... 2-4

3-1 Initial screen ...................................................................................................................... 3-1

3-2 Initial screen (R3560 mode) ............................................................................................. 3-1

3-3 BER measurement screen ................................................................................................. 3-5

3-4 Dialog box for BER measurement screen ......................................................................... 3-5

3-5 Sens measurement screen ................................................................................................. 3-7

3-6 Dialog box screen for Sens Parameter setting .................................................................. 3-7

3-7 SETUP setting screen ....................................................................................................... 3-9

3-8 Timing of RF signal output vs the Burst Trigger input signal .......................................... 3-11

3-9 SLOT setting screen .......................................................................................................... 3-12

3-10 Save operation screen ....................................................................................................... 3-16

3-11 BER measurement screen (in occurrence of Sync error) .................................................. 3-17

3-12 BER measurement connection .......................................................................................... 3-18

4-1 Initial screen ...................................................................................................................... 4-1

4-2 Initial Screen (R3561 mode) ............................................................................................. 4-1

4-3 General Dialog Screen ...................................................................................................... 4-6

4-4 Frame A Dialog Box Screen ............................................................................................. 4-8

4-5 Edit Menu Dialog Box Screen .......................................................................................... 4-10

4-6 Freq Para. Dialog Screen .................................................................................................. 4-11

4-7 Level Para. Dialog Screen ................................................................................................ 4-12

4-8 Other Screen ..................................................................................................................... 4-13

4-9 Clock Dialog Box Screen ................................................................................................. 4-13

4-10 Cal/Self Test Screen .......................................................................................................... 4-15

4-11 Save/Recall Display Screen .............................................................................................. 4-16

5-1 Initial Screen (For the R3562 Standard Configuration) .................................................... 5-1

5-2 Initial Screen (with the R3562 OPT 65 Installed) ............................................................ 5-2

5-3 R3562 Control Main Screen (3GPP) ................................................................................ 5-3

5-4 BER Parameter Setup Dialog Box .................................................................................... 5-9

5-5 Clock/Timing Signal Parameter Setup Dialog Box .......................................................... 5-10

5-6 General Parameter Setup Dialog box (For the Downlink) ............................................... 5-11

5-7 General Parameter Setup Dialog box (For the Uplink) .................................................... 5-11

5-8 STD Parameter Setup Dialog box ..................................................................................... 5-15

5-9 DPCCH Parameter Setup Dialog box (For the Downlink) ............................................... 5-16

5-10 DTCH/DCCH Parameter Setup Dialog box (For the Downlink) ..................................... 5-17

5-11 DPCCH Parameter Setup Dialog box (For the Uplink) .................................................... 5-19

5-12 DTCH/DCCH Parameter Setup Dialog box (For the Downlink) ..................................... 5-20

5-13 Ext Trigger Parameter Setup Dialog box .......................................................................... 5-21

5-14 Frequency Parameter Setup Dialog Box ........................................................................... 5-22

5-15 Level Parameter Setup Dialog Box .................................................................................. 5-22

5-16 Clock/Timing Signal Parameter Setup Dialog Box .......................................................... 5-23

F-2

R3267 Series Option08 Rx Control Option Operation Manual

List of Illustrations

No. Title Page

5-17 External I/Q Parameter Setup Dialog Box ........................................................................ 5-24

5-18 Save Register List Dialog Box .......................................................................................... 5-25

5-19 Recall Register List Dialog Box ....................................................................................... 5-26

5-20 Connecting the DUT .........................................................................................................5-27

5-21 STD Parameter Setup Dialog Box .................................................................................... 5-28

5-22 General Parameter Setup Dialog Box ............................................................................... 5-29

5-23 DTCH/DCCH Parameter Setup Dialog Box .................................................................... 5-30

5-24 BER Parameter Setup Dialog Box .................................................................................... 5-30

5-25 Measurement Result on the Bit Error Rate ....................................................................... 5-31

6-1 Initial Screen ..................................................................................................................... 6-1

6-2 R3562 Control Main Screen (cdma2000) ......................................................................... 6-2

6-3 BER Parameter Setup Dialog Box .................................................................................... 6-11

6-4 Clock/Timing Signal Parameter Setup Dialog Box .......................................................... 6-12

6-5 General Parameter Setup Dialog Box <When Reverse Is Set to RC 1 or RC 2> ............. 6-13

6-6 General Parameter Setup Dialog Box <When Reverse Is Set to RC 3 or RC 4> ............. 6-15

6-7 General Parameter Setup Dialog Box <When Forward Is Set to RC 1 or RC 2> ............ 6-18

6-8 General Parameter Setup Dialog Box <When Forward Is Set to RC 3, RC4 or RC5> .... 6-21

6-9 STD Parameter Setup Dialog box ..................................................................................... 6-24

6-10 Frame Parameter Setup Dialog Box <When Reverse Is Set to RC 1> ............................. 6-24

6-11 Frame Parameter Setup Dialog Box <When Reverse Is Set to RC 2> ............................. 6-24

6-12 Frame Parameter Setup Dialog Box <When Reverse Is Set to RC 3> ............................. 6-25

6-13 Frame Parameter Setup Dialog Box <When Reverse Is Set to RC 4> ............................. 6-26

6-14 Frame Parameter Setup Dialog Box <When Forward Is Set to RC 1> ............................ 6-27

6-15 Frame Parameter Setup Dialog Box <When Forward Is Set to RC2> ............................. 6-27

6-16 Frame Parameter Setup Dialog Box <When Forward Is Set to RC3> ............................. 6-29

6-17 Frame Parameter Setup Dialog Box <When Forward Is Set to RC4> ............................. 6-29

6-18 Frame Parameter Setup Dialog Box <When Forward Is Set to RC5> ............................. 6-30

6-19 Traffic Channel A Parameter Setup Dialog Box .............................................................. 6-31

6-20 PICH Parameter Setup Dialog Box .................................................................................. 6-32

6-21 DCCH Parameter Setup Dialog Box ................................................................................ 6-33

6-22 Traffic Channel A Parameter Setup Dialog Box .............................................................. 6-33

6-23 Traffic Channel B Parameter Setup Dialog Box .............................................................. 6-34

6-24 Traffic Channel C Parameter Setup Dialog Box .............................................................. 6-35

6-25 Traffic Channel A Parameter Setup Dialog Box .............................................................. 6-36

6-26 Traffic Channel B Parameter Setup Dialog Box .............................................................. 6-37

6-27 Traffic Channel C Parameter Setup Dialog Box .............................................................. 6-37

6-28 Traffic Channel A Parameter Setup Dialog Box .............................................................. 6-38

6-29 Traffic Channel B Parameter Setup Dialog Box .............................................................. 6-39

6-30 Traffic Channel C Parameter Setup Dialog Box .............................................................. 6-40

6-31 Frequency Parameter Setup Dialog Box ........................................................................... 6-41

6-32 Level Parameter Setup Dialog Box .................................................................................. 6-41

6-33 Clock/Timing Signal Parameter Setup Dialog Box .......................................................... 6-42

6-34 External I/Q Parameter Setup Dialog Box ........................................................................ 6-44

6-35 Save Register List Dialog Box .......................................................................................... 6-45

6-36 Recall Register List Dialog Box ....................................................................................... 6-45

6-37 Connecting the DUT .........................................................................................................6-46

6-38 STD Parameter Setup Dialog Box .................................................................................... 6-47

R3267 Series Option08 Rx Control Option Operation Manual

List of Illustrations

F-3

No. Title Page

6-39 Clock/Timing Signal Parameter Setup Dialog Box .......................................................... 6-47

6-40 General Parameter Setup Dialog Box ............................................................................... 6-48

6-41 Frame Parameter Setup Dialog Box <Reverse: RC1> ...................................................... 6-49

6-42 Traffic Channel A Parameter Setup Dialog Box .............................................................. 6-50

Otros manuales para R3264

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de ADVANTEST

ADVANTEST

ADVANTEST R3131 Series Manual de usuario

ADVANTEST

ADVANTEST R3465 Series Manual de usuario

ADVANTEST

ADVANTEST R3765G Series Manual de usuario

ADVANTEST

ADVANTEST R3763B Manual de usuario

ADVANTEST

ADVANTEST R3267 series Manual de usuario

ADVANTEST

ADVANTEST R3131 Series Manual de usuario

ADVANTEST

ADVANTEST R3131A Manual de usuario

ADVANTEST

ADVANTEST R3267 series Manual de usuario

ADVANTEST

ADVANTEST R3755 Series Manual de usuario

ADVANTEST

ADVANTEST R3261C Manual de instalación

ADVANTEST

ADVANTEST R3267 series Manual de usuario

ADVANTEST

ADVANTEST TQ8210 Manual de usuario

ADVANTEST

ADVANTEST R3132 Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario