Advantech PPC-MB-8260AE Manual de instalación y operación
PPC-MB-8260AE Startup Manual 1
Before card installation, ensure that the following items
have been included in your shipment:
1. 1 x PPC-MB-8260AE Intel® Core™ i7/i5/i3/Pentium/
Celeron LGA1151 mini-ITX motherboard
2. 4 x COM cable (2 x 5 pin)
3. 1 x SATA cable
4. 1 x Startup manual
5. 1 x Warranty card
6. 1 x Thermal grease
7. 14 x Screws for COM port
8. 1 x Packet screws for mini PCIe
If any of the above items are missing or damaged, contact
your distributor or sales representative immediately.
Note 1: For the detailed contents of PPC-MB-8260AE,
please refer to the latest product information
provided on the Advantech website (PPC-6151C
model).
Note 2: Acrobat Reader is required to view any PDF
file. Acrobat Reader can be downloaded from
www.adobe.com/Products/acrobat/readstep2.
html (Acrobat is a trademark of Adobe)
PPC-MB-8260AE (Intel® Core™ i7/i5/i3/Pentium/
Celeron LGA 1151 Mini-ITX with DP/VGA, 5 COM,
6 USB, Dual LAN, PCIe x4, Mini PCIe, DDR4)
Startup Manual
Selected
M/B
PPC-MB-8260AE
CPU
i7-
6700TE
i5-
6500TE
i3-
6100TE
Pentium
G4400TE
Celeron
G3900TE
Quad
Core
Quad
Core
Dual
Core
Dual
Core
Dual
Core
3.4GHz 3.3GHz 2.7GHz 2.4GHz 2.3GHz
8MB 6MB 4MB 3MB 2MB
35W 35W 35W 35W 35W
Chipset
H110
Memory
1 x 260-pin SODIMM DDR4, 2133 MHz,
up to 16 GB
Network
(LAN)
2 x 10/100/1000 Mbps Ethernet, Intel 211
x 2
I/O Port
1 x RS232/422/485,1 x RS232
1 x DP
1 x VGA
4 x USB (3.0)
1 x Line-Out,1 x Mic-In
Internal
Connector
3 x RS232
1 x GPIO (8 channels)
1 x Speaker connector
1 x LED connector
2 x USB 2.0
1 x LVDS connector
1 x Touch connector
2 x SATA connector
Watchdog
Timer
255 Timer levels, congurable using
software
Expansion
1 x Full-size mSATA or mini PCIe, 1 x PCIe
x4 slot
Dimensions
170 x 170 mm (6.69 x 6.69”)
OS
Support
Microsoft® Windows 7 (32/64 bit)/
Windows 8.1 (64 bit)/Windows 10 (64 bit)
Specications Packing List
For more information about this or other Advantech
products, please visit our website at
http://www.advantech.com
For technical support and service, please visit our
support website at
http://support.advantech.com
This manual is for PPC-MB-8260AE, Rev. A1.
Part No. 2003826001
Printed in China
Edition 2
October 2016
2 PPC-MB-8260AE Startup Manual
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each of the jumpers and connectors.
Connectors and Headers
Connectors and Headers List
Label Function
CN2 Mic-In/Line-Out Connector
LAN2_USB1 RJ45+USB 3.0 Stack Connector
LAN1_USB1 RJ45+USB 3.0 Stack Connector
VGA1 VGA Display Connector
DP1 Display Port Connector
CN1 COM 1/COM 2 Connector
DCIN1 Power Input Connector
ATX12v1 ATX 12V Power Supply Connector
ATX_5Vsb1 ATX 5VSB Power Supply Connector
CN5 Power Button Connector
CN6 ~ 8 COM 5/4/3 Connector
CN11 General Purpose I/O Pin Header
BAT1 Battery Connector
SPI1 SPI BIOS Flash Socket
CN16 Touch Connector
CN17 LVDS Panel Connector
CN20 LVDS Backlight Inverter Power
Connector
Sysfan1 ~ 2 System Fan Power Connector
CPUFAN1 CPU Fan Power Connector
CN18 ~ 19 SATA Power Connector
SATA1 ~ 2 SATA Signal Connector
CN4 Power LED Connector
CN9/CN12 2 x USB 2.0 Pin Header
PCIex4_1 PCIe x4 Slot Connector
AMP1 Audio Amplier Output Connector
DIMMA1 DDR4 SODIMM Socket
CPU1 CPU Socket
Mini-PCIe1 MSATA and Mini PCIe Socket
ATX_5Vsb1: ATX 5VSB Power Supply Connector
Pin Denition
1 +V5SB
2 GND
3 PSON
CN1: COM 2 Connector
Pin Denition
(RS232)
Denition
(RS422)
Denition
(RS485)
1DCD TX- TX-
2RXD TX+ TX+
3TXD RX+
4DTR RX-
5 GND
6 DSR
7RTS
8 CTS
9 RI
CN6 ~ 8: COM 5/4/3 Connector
Pin Denition
1 DCD
2 RXD
3 TXD
4 DTR
5 GND
6 DSR
7RTS
8 CTS
9 RI
10 NA
CN11: General Purpose I/O Pin Header
Pin Denition
1 GND
2 GPIO4
3 GPIO0
Jumpers and Connectors (Cont.)
Jumpers and Connectors
PPC-MB-8260AE Startup Manual 3
CN4: Power LED Connector
Pin Denition
1 +V5_DUAL
2 +V5
3 GND
4 GND
AMP1: Audio Amplier Output Connector
Pin Denition
1 SPK L-
2 SPK L+
3 SPK R+
4 SPK R-
Jumper Settings
Jumpers List
Jumper Function
JP1 ATX/AT Select
JCMOS1 RTC Select
JP2 Touch Power Select
JP3 LCD Power Select
JP4 Enable Power Select
JP5 LVDS PWM Power Select
JP6 COM Pin 9 Power Select (COM 1 & 2)
JP7 LVDS Resolution Select
ATX/AT Select (JP1)
(1-2) P1 AT
(2-3) P2 ATX (default)
P1 P2
4 GPIO5
5 GPIO1
6 GPIO6
7 GPIO2
8 GPIO7
9 GPIO3
10 +V5
CN16: Touch Connector
Pin Denition
1 Y+
2 X+
3 SENSE
4Y-
5 X-
Sysfan 1 ~ 2: System Fan Power Connector
Pin Denition
1 GND
2 POWER
3 SPEED
4 PWM
CPUFAN1: CPU Fan Power Connector
Pin Denition
1 GND
2 POWER
3 SPEED
4 PWM
CN18 ~ 19: SATA Power Connector
Pin Denition
1 +V3.3
2 GND
3 +V5
4 GND
5 +V12
Jumpers and Connectors (Cont.)
Jumpers and Connectors (Cont.)
4 PPC-MB-8260AE Startup Manual
RTC Select (Jcmos1)
(1-2) P3 Normal (default)
(2-3) P4 Clear CMOS
P3 P4
Touch Power Select (JP2)
(1-2) P5 +V3.3_DUAL (default)
(2-3) P6 +V3.3
P5 P6
LCD Power Select (JP3)
(1-2) P7 +V5
(2-3) P8 +V3.3 (default)
P7 P8
Enable Power Select (JP4)
(1-2) P9 +V5
(2-3) P10 +V3.3 (default)
P9 P10
Jumpers and Connectors (Cont.)
Jumpers and Connectors (Cont.)
LVDS PWM Power Select (JP5)
(1-2) P11 +V5
(2-3) P12 +V3.3 (default)
P11 P12
COM Ring Select (JP6)
(1-3)/(2-4)
P13/P14
COM 2/1 Ring (default)
(3-5)/(4-6)
P15/P16
COM 2/1 5V
(7-9)/(8-10)
P17/P18
COM 2/1 12V
P13 P14
P15 P16
P17 P18
LVDS Resolution Select (JP7)
(1-2)/(5-6)/
(7-8) P19
1024*768 (24 bit)
(1-2)/(7-8)
P20
1280*1024 (24 bit)
P19 P20
PPC-MB-8260AE Startup Manual 5
Board Layout: Jumper and Connector Locations
Installation Guide
1. Insert the memory module into the memory slot at a 45
degree angle, as shown below. Ensure that the gold
fingers of the module are fully inserted into the slot.
45°
2. Once inserted, gently press the memory module into
the slot until the tabs snap into place, securing the
module in position.
6 PPC-MB-8260AE Startup Manual
1.1 Entering BIOS Setup
When the power is turned on, press the <Del> button to
enter the BIOS setup screen.
After a setting is configured, press <F4> to save and exit;
otherwise, the configuration will not be saved in the BIOS.
1.2 COM 2 Mode Selection (RS232/422/
RS485)
1. Access the “Super IO Configuration” item from the
“Advanced” tab.
2. Select “Serial Port 2 Configuration”. The COM 2 mode
can be configured via the “Device Mode” item.
BIOS Setup Program
3. Select the “RS485” option. Autoflow and termination
resistors can be enabled or disabled.
1.3 H/W Monitor and Smart Fan Mode
Configuration
1. Access the “H/W Monitor” item from the “Advanced”
tab to check the voltage temperature and fan speed.
1.4 LAN PXE Mode Selection
1. Access the “Network Stack Configuration” item from
the “Advanced” tab.
BIOS Setup Program (Cont.)
PPC-MB-8260AE Startup Manual 7
2. Select the “Enabled” option for the “Network Stack”
item.
1.5 Boot Option Filter
1. Access the “CSM Configuration” items from the
“Advanced” tab. Users can select “UEFI only” or
“Legacy only” for “Boot Option Filter” configuration.
2. Configure the Video and Storage item settings to match
with the Boot Option Filter configuration.
BIOS Setup Program (Cont.)
BIOS Setup Program (Cont.)
1.6 Graphics Configuration
1. Access the “System Agent (SA) Configuration” item
from the “Chipset” tab.
2. Click on the “Graphics Configuration” item.
3. Select the “LCD Control” item.
8 PPC-MB-8260AE Startup Manual
4. The Primary IGFX Boot Display item can be configured
as “VBIOS Default”, “DP”, “LVDS”, or “CRT”.
5. The Brightness Mode Control item configuration is set
to “Chipset” by default. This means users can adjust
the system brightness via the OS brightness dimmer.
6. Access the “Brightness Manual Control” item to select
from six brightness level options.
BIOS Setup Program (Cont.)
BIOS Setup Program (Cont.)
1.7 Wake On LAN and Ring
1. In the “Chipset” tab click the “PCH-IO Configuration”
item to access “PCIE Wake” configuration. Select the
“Enabled” option to allow wake-on-LAN function.
2. In the “Chipset” tab click the “PCH-IO Configuration”
item to access “Wake on Ring” configuration. Select
the “Enabled” option to allow wake-on-ring function.
1.8 AT and ATX Setting
In the “Chipset” tab click the “PCH-IO Configuration” item
to access the “Restore AC Power Loss” item. Set the item
configuration to “Power On”, “Power Off”, or “Last State”.
Tabla de contenidos
Otros manuales de Placa madre de Advantech
Advantech
Advantech AIMB-780 Manual de usuario
Advantech
Advantech PCA-6781 Manual de usuario
Advantech
Advantech PCI-6886F-M0A1 Manual de usuario
Advantech
Advantech MIO-2360 SBC Manual de usuario
Advantech
Advantech PCA-6289 Manual de instalación y operación
Advantech
Advantech SIMB-A01 Manual de instalación y operación
Advantech
Advantech AIMB-225 Manual de usuario
Advantech
Advantech AIMB-584 Manual de usuario
Advantech
Advantech IPC-5122 Manual de usuario
Advantech
Advantech PCM-5820 Series Manual de instalación y operación
Advantech
Advantech PCA-6751 Series Manual de instalación y operación
Advantech
Advantech ROM-7420 Manual de usuario
Advantech
Advantech ASMB-782 Manual de instalación y operación
Advantech
Advantech POD-6552 Manual de instalación y operación
Advantech
Advantech ASMB-584 Manual de instalación y operación
Advantech
Advantech PCA-6168 Manual de usuario
Advantech
Advantech PCE-3028 Manual de usuario
Advantech
Advantech PCM-4153-A2 Manual de instalación y operación
Advantech
Advantech PCA-6181 Manual de usuario
Advantech
Advantech AIMB-223G2-S2A2E Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
