Advantech MIC-3355 Manual de usuario
MIC-3355
6u-sized Pentium®processor-based
CPU module for CompactPCI ®
MIC-3355 User's Manual
Copyright Notice
This document is copyrighted, 1998. All rights are reserved. The
original manufacturer reserves the right to make improvements to the
products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, nor for any
infringements upon the rights of third parties which may result from
its use.
Acknowledgements
AMD is a trademark of Advanced Micro Devices, Inc.
Award is a trademark of Award Software International, Inc.
Cyrix is a trademark of Cyrix Corporation.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business
Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows®is a registered trademark of Microsoft Corp.
PICMG™, CompactPCI™ and the PICMG™, CompactPCI™ logos
are trademarks of the PCI Industrial Computers Manufacturers Group
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
SiS is a trademark of Silicon Integration Systems Corporation.
All other product names or trademarks are properties of their
respective owners.
PartNo.2006335520 3rd Edition
Printedin TaiwanJanuary2000
Preface and Table of Contents
Packing List
Before installing your board, ensure that the following materials have
been received:
• 1 MIC-3355 all-in-one single board computer
• 1CD-ROM disc including Ethernet utility programs, IDE utility
programs and SVGA utility programs and drivers for Windows 3.1/
95/NT and OS/2
• 1 hard disk drive (IDE) interface cable (44-pin)
• 1 warranty certificate
• This user's manual
If any of these items are missing or damaged, contact your distributor
or sales representative immediately.
MIC-3355 User's Manual
Contents
Chapter 1: Hardware Configuration ............................................ 1
1.1 Introduction.................................................................... 2
1.2 Specifications.................................................................. 3
1.2.1 Standard SBC functions .............................................. 3
1.2.2 PCI-to-PCI Bridge ...................................................... 4
1.2.3 VGA interface............................................................. 4
1.2.4 100Base-T Ethernet Interface..................................... 4
1.2.5 Mechanical and environmental specifications ............. 5
1.3 Board Layout: Dimensions .......................................... 6
1.4 Jumpers and Connectors ............................................. 7
1.5 Board Layout: Jumper Locations ............................... 8
1.6 Board Layout: Connector Locations........................ 10
1.7 Safety Precautions ....................................................... 11
1.8 Jumper Settings........................................................... 12
1.9 Installing SDRAM (DIMMs) .................................... 15
Chapter 2: Connecting Peripherals ........................................... 17
2.1 IDE Device connector (CN10)
and Floppy Drive connector (CN9) ............................... 19
2.2 VGA Display Connector (CN2)..................................... 21
2.3 Parallel Port Connector (CN6)...................................... 21
2.4 Keyboard and PS/2 Mouse Connector (CN1).............. 21
2.5 Serial Ports (CN6: COM1 and COM2)......................... 21
2.5.1 RS-232 connection (COM1-CN6) ............................. 22
2.5.2 RS-232/422/485 connection (COM2-CN6) ............... 22
2.6 Power Connectors (CN7 & CN8) .................................. 22
2.6.1 Main power connector +5 V, +12 V (CN7) ............... 22
2.6.2 CPU fan power supply connector (CN8)................... 23
2.7EthernetConfiguration(CN4)....................................... 23
RJ-45A connector (CN4) .................................................... 23
Network boot ...................................................................... 23
2.8 USB Connector (CN5)................................................ 23
Preface and Table of Contents
2.9 IR Interface (LED1).................................................... 24
2.10 Card Installation ......................................................... 24
Chapter 3: VGA Display & Ethernet Software Configuration ... 27
3.1 Introduction.................................................................. 28
3.2 Utility and Drivers ....................................................... 28
3.3 VGA Display Setup and Configuration ..................... 30
3.3.1 VGA Display Setup and Configuration for DOS .......30
3.3.2 VGA Driver Setup for Autodesk
ADI 4.2 (Protected Mode) ............................................ 32
3.3.3VGADisplaySetupandConfiguration
for Microsoft Windows NT 3.5x .................................. 32
3.3.4VGADisplaySetupandConfiguration
for Microsoft Windows NT 4.0 .................................... 34
3.3.5VGADisplaySetupandConfiguration
for Microsoft Windows 95............................................ 35
3.3.6VGADisplaySetupandConfiguration
for Microsoft Windows 3.x............................................ 36
3.3.7VGADisplaySetupandConfiguration
for IBM OS/2 Ver. 2.1 .................................................... 39
3.3.8VGADisplaySetupandConfiguration
for IBM OS/2 Warp 3.0 (Double Byte Character).......... 39
3.3.9VGADisplaySetupandConfiguration
for IBM OS/2 Warp 3.0 (Single Byte Character) ............40
3.4 Ethernet Software Configuration ............................... 41
Chapter 4: Award BIOS Setup ................................................... 43
4.1 AWARD BIOS Setup................................................... 44
4.1.1 Entering setup ............................................................44
4.1.2 Standard CMOS setup ..............................................45
4.1.3 BIOS features setup..................................................46
4.1.4 CHIPSET features setup ..........................................50
4.1.5 Power management setup .........................................51
4.1.6 PCI configuration setup .............................................52
4.1.7 Load BIOS defaults...................................................52
MIC-3355 User's Manual
4.1.8 Load setup defaults ...................................................52
4.1.9 Integrated Peripherals ...............................................53
4.1.10 Password setting.......................................................53
4.1.11 IDE HDD auto detection ..........................................53
4.1.12 Save & exit setup .....................................................54
4.1.13 Exit without saving....................................................54
Appendix A: Programming the Watchdog Timer .................... 55
A.1 Programming the Watchdog Timer.......................... 56
Appendix B: Pin Assignments ................................................... 59
B.1 CRT Display Connector (CN2) ............................. 60
B.2 COM1 RS-232 Serial Port (CN6) ......................... 60
B.3 COM2 RS-232/422/485 Serial Port (CN6).......... 61
B.4 Keyboard and Mouse Connnector (CN1) ........... 61
B.5 Main Power Connector (CN7) .............................. 62
B.6 IDE Hard Drive Connector (CN10)..................... 63
B.7 USB Connector (CN5) ........................................... 64
B.8 CPU Fan Power Connector (CN8) ....................... 64
B.9 Ethernet RJ-45 Connector (CN4)........................ 65
B.10 Floppy Drive Connector (CN9) ............................ 66
B.11 Parallel Port Connector (CN6).............................. 67
B.12 System I/O Ports ..................................................... 68
B.13 DMA Channel Assignments ................................. 69
B.14 Interrupt Assignments........................................... 70
B.15 1st MB Memory Map ............................................ 70
B.16 J3 Connector Pin Assignments ............................ 71
Preface and Table of Contents
Figures
Figure 1-1: MIC-3355 board layout: Dimensions ................................ 6
Figure 1-2: MIC-3355 board layout: Jumper locations ...................... 8
Figure 1-3: MIC-3355 board layout: Connector locations ............... 10
Figure 1-4: MIC-3355 board layout: Jumper settings ...................... 13
Figure 2-1: Installing the HDD ............................................................ 20
Figure 2-2: Installing the card into the chassis ............................... 25
Figure 4-1: Setup program initial screen ......................................... 44
Figure 4-2: CMOS setup screen ....................................................... 45
Figure 4-3: BIOS features setup screen .......................................... 46
Figure 4-4: CHIPSET features setup screen .................................... 50
Figure 4-5: Power management setup screen ............................... 51
Figure 4-6: PCI configuration screen ............................................... 52
Figure 4-7: Integrated peripherals ................................................... 53
Tables
Table 1-1: MIC-3355 jumpers ............................................................ 7
Table 1-2: MIC-3355 connectors ....................................................... 8
Table 1-3: CPU clock ratio setting ................................................... 14
Table 2-1: List of connectors .......................................................... 18
Table 2-3: MIC-3355 serial port default settings ............................ 22
Table B-1: MIC-3355 CRT display connector .................................. 60
Table B-2: MIC-3355 COM1 RS-232 serial port ............................... 60
Table B-3: MIC-3355 COM2 RS-232/422/485 series port ............... 61
Table B-4: MIC-3355 keyboard connector ...................................... 61
Table B-5: MIC-3355 mouse connector .......................................... 62
Table B-6: MIC-3355 main power connector .................................. 62
Table B-7: MIC-3355 IDE hard drive connector ............................... 63
Table B-8: USB1/USB2 connector ................................................... 64
Table B-9: MIC-3355 CPU fan power connector ............................. 64
Table B-10: MIC-3355 Ethernet RJ-45 connector ............................. 65
Table B-11: MIC-3355 floppy drive connector ................................... 66
Table B-12: MIC-3355 parallel port connector .................................. 67
Table B-13: System I/O ports ............................................................. 68
Table B-14: DMA channel assignments ............................................ 69
Table B-15: Interrupt assignments ................................................... 70
Table B-16: 1st MB memory map ...................................................... 70
Table B-17: J3 Connector Pin Assignments ..................................... 71
1
Hardware
Configuration
This chapter gives background
information on the MIC-3355. It then
shows you how to configure the card to
match your application and prepare it for
installation into your chassis.
Sections include:
• Card specifications
• Board layout: dimensions
• Board layout: jumper locations
• Board layout: connector locations
• Safety precautions
• Jumper settings
• InstallingSDRAM (DIMMs)
CHAPTER
2MIC-3355 User's Manual
1.1 Introduction
TheMIC-3355 isa 6U-sizedCompactPCI™, all-in-onesingleboard
Pentium®processor-based CPU card which complies with PICMG 2.0
R2.1 CompactPCI specifications. The MIC-3355 offers all the functions
of an industrial computer on a single board CPU card. This card
supports an Intel Pentium, Pentium MMX, AMD K5, AMD K6, Cyrix
M1 or Cyrix M2 processor. The card accepts up to 256 MB SDRAM. It
also supports on-board 512 KB PB-SRAM 2nd level cache.
The MIC-3355 uses a single-chip solution, allowing on-board DRAM
to be shared with the built-in VGA controller. In this configuration, the
chipset always acts as the arbiter between memory bus masters. This
system ensures efficient memory allocation while substantially
reducing the overall system cost.
On-boardfeatures include512 KB2nd level cachememory,100/10
Mbpsfast Ethernetinterface, oneRS-232 port,one RS-232/422/485
port,one multi-modeparallel (ECP/EPP/SPP)port, afloppy drive
controller and a keyboard and PS/2 mouse interface. The built-in high
speed PCI IDE controller supports both PIO and bus master modes.
Two IDE channels are available through the J3 connector and one
channel is available through the on-board connector. Up to two IDE
devices can be connected to one channel, including large hard disks,
CD-ROM drives, tape backup drives and other IDE devices. The MIC-
3355 also supports two USB ports and one fast infrared port.
TheMIC-3355 alsofeatures powermanagement tominimize power
consumption. It complies with the "Green Function" standard and
supports three types of power saving features: Doze mode, Standby
mode and Suspend mode. A watchdog timer can automatically reset
the system or generate an interrupt should the system stop due to a
program bug or EMI.
Chapter 1 Hardware Configuration 3
1.2 Specifications
1.2.1 Standard SBC functions
•CPU:IntelPentium®,Pentium MMX,AMDK5, AMDK6, Cyrix M1,
CyrixM2, orIDTWinChipC6
•BIOS:Award 256 KB (2 Mbit) memory; supports plug and play
•Chipset:SiS5598
•L2 cache: On-board 512 KB synchronous (pipeline burst) SRAM
•Greenfunction:Features powermanagement optionvia BIOS,
activated by keyboard or mouse activity. Supports doze, standby
and suspend modes. APM 1.1 compliant
•RAM:Two 168-pinDIMM sockets.Supports SDRAMwith memory
capacity up to 256 MB
•EIDEinterface: Handlesup to4 IDEHDDs orother IDEdevices via
the J3 connector, or 2 IDE devices through the on-board connector.
Supports PIO mode 4 and Ultra DMA mode
•FDD interface: Supports up to two floppy disk drives through the J3
connector or on-board connector
•Parallelport: Configuredto LPT1,LPT2,LPT3 ordisabled.
Supportsmulti-mode parallelport(SPP/ECP/EPP)
•Serialports:Two16C550 UARTs,one RS-232,oneRS-232/422/485
interface
•Watchdogtimer: Can generate a system reset or IRQ 15. Software
enabled/disabled. Time interval is from 1 to 63 seconds, jumperless
with run-time setup
•Keyboard/mouseconnector: 6-pinmini-DIN connectoronthe front
panel
•USBinterface:Two USB connectors with fuse protection. Complies
withUSB specification1.0
•Infraredport:Fast IrDA. Transfer rate up to 4 Mbps. I/O port
programmabletoCOM1 (3F8),COM2(2F8),COM3(3E8) orCOM4
(2E8).
Tabla de contenidos
Otros manuales de Placa madre de Advantech
Advantech
Advantech PCM-9365 Manual de instalación y operación
Advantech
Advantech AIMB-556 Manual de usuario
Advantech
Advantech MIC-3385 Manual de usuario
Advantech
Advantech AIMB-506 Manual de usuario
Advantech
Advantech PCA-6188 Manual de instalación y operación
Advantech
Advantech PCM-9310 Manual de usuario
Advantech
Advantech AIMB-708 Manual de usuario
Advantech
Advantech AIMB-281 Manual de usuario
Advantech
Advantech PCA-6153 Manual de usuario
Advantech
Advantech PCA-6751 Series Manual de usuario
Advantech
Advantech MIO-2360 SBC Manual de instalación y operación
Advantech
Advantech PCA-6774 Manual de usuario
Advantech
Advantech PCA-6028 Manual de usuario
Advantech
Advantech PCA-6289 Manual de usuario
Advantech
Advantech PCM-5824 Manual de instalación y operación
Advantech
Advantech DVMB-554E Manual de usuario
Advantech
Advantech ASMB-782 Manual de instalación y operación
Advantech
Advantech RSB-4221 Manual de usuario
Advantech
Advantech AIMB-281 Manual de usuario
Advantech
Advantech PCI-6881 Series Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
