Advantech PCL-722 Manual de usuario

PCL-722

144-ch Digital I/O ISA Card

User Manual

PCL-722 User Manual ii

The documentation and the software included with this product are copy-

righted 2011 by Advantech Co., Ltd. All rights are reserved. Advantech

Co., Ltd. reserves the right to make improvements in the products

described in this manual at any time without notice. No part of this man-

ual may be reproduced, copied, translated or transmitted in any form or

by any means without the prior written permission of Advantech Co., Ltd.

Information provided in this manual is intended to be accurate and reli-

able. However, Advantech Co., Ltd. assumes no responsibility for its use,

nor for any infringements of the rights of third parties, which may result

from its use.

Acknowledgements

PC-LabCard is a trademark of Advantech Co., Ltd.

IBM, PC are trademarks of International Business Machines Corporation.

MS-DOS, Windows, Microsoft Visual C++ and Visual BASIC are

trademarks of Microsoft Corporation.

Intel and Pentium are trademarks of Intel Corporation.

Delphi and C++ Builder are trademarks of Borland Corporation.

Part No. 2003722010 1st Edition

Printed in Taiwan November 2011

iii

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its prod-

ucts will be free from defects in materials and workmanship for two years

from the date of purchase.

This warranty does not apply to any products which have been repaired or

altered by persons other than repair personnel authorized by Advantech,

or which have been subject to misuse, abuse, accident or improper instal-

lation. Advantech assumes no liability under the terms of this warranty as

a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous test-

ing, most of our customers never need to use our repair service. If an

Advantech product is defective, it will be repaired or replaced at no

charge during the warranty period. For out-of-warranty repairs, you will

be billed according to the cost of replacement materials, service time and

freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For

example, CPU speed, Advantech products used, other hardware

and software used, etc.) Note anything abnormal and list any

onscreen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your man-

ual, product, and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return

merchandize authorization) number from your dealer. This allows

us to process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and

Replacement Order Card and a photocopy proof of purchase date

(such as your sales receipt) in a shippable container. A product

returned without proof of the purchase date is not eligible for war-

ranty service.

5. Write the RMA number visibly on the outside of the package and

ship it prepaid to your dealer.

PCL-722 User Manual iv

Declaration of Conformity

This product has passed the CE test for environmental specifications

when shielded cables are used for external wiring. We recommend the use

of shielded cables. This kind of cable is available from Advantech. Please

contact your local supplier for ordering information.

FCC Class A

Note: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environ-

ment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Opera-

tion of this equipment in a residential area is likely to cause harmful inter-

ference in which case the user will be required to correct the interference

at his own expense.

Technical Support and Assistance

Step 1. Visit the Advantech web site at www.advantech.com/support

where you can find the latest information about the product.

Step 2. Contact your distributor, sales representative, or Advantech's cus-

tomer service center for technical support if you need additional

assistance. Please have the following information ready before

you call:

- Product name and serial number

- Description of your peripheral attachments

- Description of your software (operating system, version, appli-

cation software, etc.)

- A complete description of the problem

- The exact wording of any error messages

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User's Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning.

Use a damp cloth. Do not use liquid detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located

near the equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Drop-

ping it or letting it fall may cause damage.

7. The openings on the enclosure are for air convection. Protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before con-

necting the equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not

place anything over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the

power source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or elec-

trical shock.

13. Never open the equipment. For safety reasons, the equipment

should be opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked

by service personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work

according to the user's manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT

WHERE THE STORAGE TEMPERATURE MAY GO BELOW -

20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAM-

PCL-722 User Manual vi

AGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A

CONTROLLED ENVIRONMENT.

16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS

INCORRECTLY REPLACED. REPLACE ONLY WITH THE

SAME OR EQUIVALENT TYPE RECOMMENDED BY THE

MANUFACTURER, DISCARD USED BATTERIES ACCORD-

ING TO THE MANUFACTURER'S INSTRUCTIONS.

The sound pressure level at the operator's position according to IEC 704-

1:1982 is no more than 70 dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1.

Advantech disclaims all responsibility for the accuracy of any statements

contained herein.

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the

products from damage.

1. To avoid electrical shock, always disconnect the power from your

PC chassis before you work on it. Don't touch any components on

the CPU card or other cards while the PC is on.

2. Disconnect power before making any configuration changes. The

sudden rush of power as you connect a jumper or install a card may

damage sensitive electronic components.

vii Table of Contents

Contents

Chapter 1 Introduction .................................................... 2

1.1 Features ............................................................................. 2

1.2 Specifications .................................................................... 2

1.2.1 Digital Input ................................................................... 2

1.2.2 Digital Output ................................................................ 3

1.2.3 General Specifications ................................................... 3

1.3 Applications ...................................................................... 3

1.4 Installation Guide .............................................................. 4

Figure 1.1:Installation Flow Chart ................................. 4

1.5 Software Overview............................................................ 5

Chapter 2 Installation ....................................................... 8

2.1 Unpacking ......................................................................... 8

2.2 Driver Installation ............................................................. 9

Figure 2.1: Advantech Automation Software Setup ...... 9

Figure 2.2:Different Options for Driver Setup ............ 10

2.3 Hardware Installation ...................................................... 11

Chapter 3 Signal Connections ........................................ 14

3.1 Overview ......................................................................... 14

3.2 Switch & Jumper Settings .............................................. 14

Figure 3.1:Card Connectors, Jumpers & Switches ...... 14

3.2.1 Base Address Selection ................................................ 15

Table 3.1:Switch Position Summary ........................... 15

3.2.2 96/144-bit Mode Setting .............................................. 16

Figure 3.2:Select 144 or 96 I/O ................................... 16

3.2.3 Interrupt Settings .......................................................... 17

Figure 3.3:Interrupt Enable Selection .......................... 17

3.3 Signal Connections.......................................................... 18

3.3.1 Configuration .............................................................. 18

Table 3.3:CFG register format (mode 0) ..................... 19

Table 3.2:8255 Address Map ....................................... 19

Table 3.4:8255 Mode 0 Configuration Table .............. 20

3.4 Interrupt Handling ........................................................... 21

Appendix A Programming Examples .............................. 24

Appendix B Block Diagram............................................... 30

Appendix C PC I/O Port Address Map ............................ 32

PCL-722 User Manual viii

CHAPTER

Introduction

This chapter contains information on the

PCL-722 and instruction on card config-

uration in order to match your applica-

tion and prepare it for installation on

your system.

Sections include:

• Features

• Specifications

• Applications

• Installation Guide

• Software Overview

PCL-722 User Manual 2

Chapter 1 Introduction

The PCL-722 144 bit DIO card is a generalized 144 line parallel digital I/

O board that has six channels. Each channel emulates mode 0 of a 8255

programmable peripheral interface chip, and has 24 lines of digital input

and/or output. Every channel has an individual connector with OPTO-22

compatible pin assignment. Two lines of each connector can be used to

generate a hardware interrupt. These inputs are buffered and can be con-

nected to IRQ 2, 3, 4, 5, 6 and 7. The PCL-722 is a full-size PC add-on

card and can fit any full-length expansion slot in the IBM PC XT/AT or

compatible computer running at any clock rate.

1.1 Features

• 144 TTL digital I/O lines, (6 connectors, each with 24 I/O lines)

• The 24 I/O lines of each connector are configured to port PA (8 bit), PB

(8 bit), PC Upper (4 bit) and PC Lower (4 bit). Each port can be pro-

grammed to digital input or digital output

• Emulates mode 0 of 8255 PPI

• Programmable interrupt handling

• OPTO-22 compatible 50-pin connector

• Direct interface to wide range of peripherals

1.2 Specifications

1.2.1 Digital Input

Channels: 144 (24 channels x 6 ports) shared with output

Compatibility: 5V/TTL

Input Voltage: Logic 0: 0.0 V ~ 0.80 V @ -0.2 mA

Logic 1: 2.0 V ~ 5.25 V @ 20 uA

Interrupt Capable Ch.: Bits 0 and 3 of Port C can generate an interrupt to

IRQ 2, 3, 4, 5, 6 or 7

Interrupt Bandwidth: 800Hz @ 0.5 Duty cycle

Tabla de contenidos

Otros manuales de Sistema de E/S de Advantech

Advantech

Advantech USB-582 Manual de instalación y operación

Advantech

Advantech APAX-5013 Manual de usuario

Advantech

Advantech ADAM-3013 Manual de usuario

Advantech

Advantech AIIS-E730 Manual de instalación y operación

Advantech

Advantech I/O Module 5000 Series Manual de usuario

Advantech

Advantech ADAM-6251 Manual de instalación y operación

Advantech

Advantech PCI-1713 Manual de usuario

Advantech

Advantech PCI-1758UDO Manual de instalación y operación

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Advantech

Advantech USB-4751 Manual de usuario

Advantech

Advantech PCIE-1762H Manual de usuario

Advantech

Advantech PCIE-1730 Series Manual de usuario

Advantech

Advantech USB-5817 Manual de instalación y operación

Advantech

Advantech PCI-1727U Manual de usuario

Advantech

Advantech UNO-2000-LKAE Manual de usuario

Advantech

Advantech PCL-730 Manual de instalación y operación

Advantech

Advantech PCIE-1756H Manual de usuario

Advantech

Advantech USB-4716 Manual de usuario

Advantech

Advantech USB-4751 Manual de usuario

Advantech

Advantech PCM-3753I-AE Manual de usuario

Advantech

Advantech 98910770500 Manual de instalación y operación

Advantech

Advantech ADAM-6050W Manual de usuario

Advantech

Advantech ADAM-6100PN Series Manual de usuario

Advantech

Advantech PCL-720 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario