Advantech IPC-603MB Manual de usuario

IPC-603MB

Ultra Compact 2U-high Rack-

mount IPC Chassis

User Manual

IPC-603MB User Manual ii

The documentation and the software included with this product are copy-

righted 2005 by Advantech Co., Ltd. All rights are reserved. Advantech

Co., Ltd. reserves the right to make improvements in the products

described in this manual at any time without notice. No part of this man-

ual may be reproduced, copied, translated or transmitted in any form or

by any means without the prior written permission of Advantech Co., Ltd.

Information provided in this manual is intended to be accurate and reli-

able. However, Advantech Co., Ltd. assumes no responsibility for its use,

nor for any infringements of the rights of third parties, which may result

from its use.

Acknowledgements

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows and MS-DOS are registered trademarks of Microsoft

Corp.

All other product names or trademarks are properties of their respective

owners.

IPC-603MB, AIMB-740, AIMB-741, AIMB-742, AIMB-744, AIMB-

750, AIMB-760, and AIMB-560 are all trademarks of Advantech Co.,

Ltd.

Note

The information in this document is provided for reference only. Advan-

tech does not assume any liability arising out of the application or use of

the information or products described herein. This manual is subject to

change without notice.

Part No. 2002060300 1st Edition

Printed in Taiwan November 2005

iii

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its prod-

ucts will be free from defects in materials and workmanship for two years

from the date of purchase.

This warranty does not apply to any products which have been repaired or

altered by persons other than repair personnel authorized by Advantech,

or which have been subject to misuse, abuse, accident or improper instal-

lation. Advantech assumes no liability under the terms of this warranty as

a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous test-

ing, most of our customers never need to use our repair service. If an

Advantech product is defective, it will be repaired or replaced at no

charge during the warranty period. For out-of-warranty repairs, you will

be billed according to the cost of replacement materials, service time and

freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For

example, CPU speed, Advantech products used, other hardware

and software used, etc.) Note anything abnormal and list any on-

screen messages you get when the problem occurs.

2. Call your dealer and describe the problem. Please have your man-

ual, product, and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return

merchandise authorization) number from your dealer. This allows

us to process your return more quickly.

4. Carefully pack the defective product, a fully-completed Repair and

Replacement Order Card and a photocopy proof of purchase date

(such as your sales receipt) in a shippable container. A product

returned without proof of the purchase date is not eligible for war-

ranty service.

5. Write the RMA number visibly on the outside of the package and

ship it prepaid to your dealer.

IPC-603MB User Manual iv

Declaration of Conformity

This product has passed the CE test for environmental specifications

when shielded cables are used for external wiring. We recommend the

use of shielded cables. This kind of cable is available from Advantech.

Please contact your local supplier for ordering information.

This product has passed the CE test for environmental specifications. Test

conditions for passing included the equipment being operated within an

industrial enclosure. In order to protect the product from being damaged

by ESD (Electrostatic Discharge) and EMI leakage, we strongly recom-

mend the use of CE-compliant industrial enclosure products.

FCC Class A

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own

expense.

Technical Support and Assistance

1. Visit the Advantech web site at www.advantech.com/support

where you can find the latest information about the product.

2. Contact your distributor, sales representative, or Advantech's cus-

tomer service center for technical support if you need additional

assistance. Please have the following information ready before you

call:

- Product name and serial number

- Description of your peripheral attachments

- Description of your software (operating system, version, applica-

tion software, etc.)

- A complete description of the problem

- The exact wording of any error messages

Document Feedback

To assist us in making improvements to this manual, we would welcome

comments and constructive criticism. Please send all such comments in

writing to: supp[email protected]

Packing List

Before setting up the system, check that the items listed below are

included and in good condition. If any item does not accord with the

table, please contact your dealer immediately.

• Item XXXXXXXX

• Box XXXXXXXXX

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning.

Use a damp cloth. Do not use liquid or spray detergents for clean-

ing.

4. For plug-in equipment, the power outlet socket must be located

near the equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Drop-

ping it or letting it fall may cause damage.

IPC-603MB User Manual vi

7. The openings on the enclosure are for air convection. Protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before con-

necting the equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not

place anything over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the

power source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or elec-

trical shock.

13. Never open the equipment. For safety reasons, the equipment

should be opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked

by service personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work

according to the user manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT

WHERE THE STORAGE TEMPERATURE MAY GO BELOW -

20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAM-

AGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A

CONTROLLED ENVIRONMENT.

16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS

INCORRECTLY REPLACED. REPLACE ONLY WITH THE

SAME OR EQUIVALENT TYPE RECOMMENDED BY THE

MANUFACTURER, DISCARD USED BATTERIES ACCORD-

ING TO THE MANUFACTURER'S INSTRUCTIONS.

The sound pressure level at the operator's position according to IEC 704-

1:1982 is no more than 70 dB (A).

vii

DISCLAIMER: This set of instructions is given according to IEC 704-1.

Advantech disclaims all responsibility for the accuracy of any statements

contained herein.

Wichtige Sicherheishinweise

1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Ver-

wenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient

ein angefeuchtetes Tuch zur Reinigung.

4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und

leicht zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten.

Ein Kippen oder Fallen könnte Verletzungen hervorrufen.

7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät

vor überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen

nicht abgedeckt werden.

8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBw-

erte.

9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber

fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen die sich am Geräten befinden sind

zu beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten

Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspan-

nung eine Beschädigung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder

Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw.

elektrischen Schlag auslösen.

13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der ele-

ktrischen Sicherheit nur von authorisiertem Servicepersonal geöff-

net werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz

zu trennen und von einer qualifizierten Servicestelle zu überprüfen:

a. Netzkabel oder Netzstecker sind beschädigt.

IPC-603MB User Manual viii

b. Flüssigkeit ist in das Gerät eingedrungen.

c. Das Gerät war Feuchtigkeit ausgesetzt.

d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend

funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesse-

rung erzielen.

e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der

Batterie.Ersatz nur durch densellben order einem vom Hersteller

empfohlene-mahnlichen Typ. Entsorgung gebrauchter Batterien

navh Angaben des Herstellers.

16. ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf

nicht fach-männische Weise gewechselt wird. Verfangen Sie die

Batterie nur gleicher oder entsprechender Type, wie vom Hersteller

empfohlen. Entsorgen Sie Batterien nach Anweisung des Herstell-

ers.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000

beträgt 70dB(A) oder weiger.

Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend

der IEC-704-1 erstellt. Advantech lehnt jegliche Verantwortung für die

Richtigkeit der in diesem Zusammenhang getätigten Aussagen ab.

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the

products from damage.

1. To avoid electrical shock, always disconnect the power from your

PC chassis before you work on it. Don't touch any components on

the CPU card or other cards while the PC is on.

2. Disconnect power before making any configuration changes. The

sudden rush of power as you connect a jumper or install a card may

damage sensitive electronic components.

ix Table of Contents

Contents

Chapter 1 General Information ....................................... 2

1.1 Introduction ....................................................................... 2

1.2 Specifications .................................................................... 2

1.3 Environmental Specifications ........................................... 3

1.4 Power Supply .................................................................... 3

1.5 Dimensions of IPC-603MB............................................... 4

Chapter 2 System Setup.................................................... 6

2.1 Removing the Cover.......................................................... 7

2.2 Installing a Motherboard ................................................... 7

2.3 Installing Disk Drives........................................................ 9

2.4 Installing Add-in Cards ................................................... 11

2.5 Installing Rackmount Brackets & Handles ..................... 11

Chapter 3 Operation ....................................................... 14

3.1 The Front Section of IPC-603MB................................... 14

3.1.1 Switches ....................................................................... 14

3.1.2 LED indicators ............................................................. 14

Table 3.1: System Status LED Summary .................... 14

3.2 Replacing the Fans .......................................................... 15

3.3 Replacing the filters ........................................................ 16

3.4 Replacing the power supply ............................................ 17

Appendix A Exploded Diagram ........................................ 20

IPC-603MB User Manual x

Tabla de contenidos

Otros manuales de Chasis de Advantech

Advantech

Advantech ACP-4340 Manual de usuario

Advantech

Advantech IPC-623 Series Manual de usuario

Advantech

Advantech HPC-7483 Manual de usuario

Advantech

Advantech ACP-4320 Manual de usuario

Advantech

Advantech HPC-7120 Manual de usuario

Advantech

Advantech ACP-4D00 Manual de usuario

Advantech

Advantech RMD-1150 Manual de usuario

Advantech

Advantech IPC-622MS Manual de usuario

Advantech

Advantech HPC-8424 Manual de usuario

Advantech

Advantech HPC-7480 Manual de usuario

Advantech

Advantech HPC-7484 Manual de usuario

Advantech

Advantech IPC-602 Manual de usuario

Advantech

Advantech ACP-2000 Manual de usuario

Advantech

Advantech EPD-B101 Manual de usuario

Advantech

Advantech IPC-7220 Manual de usuario

Advantech

Advantech IPC-602 Manual de usuario

Advantech

Advantech AIMB-B1000 Series Manual de usuario

Advantech

Advantech IPC-3026 Manual de usuario

Advantech

Advantech IPC-3012 Manual de usuario

Advantech

Advantech ACP-1000MB Manual de usuario

Advantech

Advantech AIMB-C200 Manual de usuario

Advantech

Advantech ACP-1320BP Manual de usuario

Advantech

Advantech HPC-7120S Manual de usuario

Advantech

Advantech IPC-7132 Manual de usuario

Manuales populares de Chasis de otras marcas

IMC Networks

IMC Networks iMcV/18 Manual de usuario

Chenbro

Chenbro RB13804N4WFT Manual de usuario

Lenovo

Lenovo ThinkSystem SR665 V3 Manual de usuario

Wuntronic

Wuntronic PCI4DRQ Manual de usuario

EtherWAN

EtherWAN EMC400 Manual de usuario

Overland Storage

Overland Storage SnapSAN S1000 Guía

Philips

Philips LC4.1E A Manual de usuario

Supermicro

Supermicro SCF418 Series Manual de usuario

Chenbro

Chenbro RM437 Series Manual de usuario

Pickering

Pickering 40-914 Manual de usuario

HP A7503-S Instrucciones de montaje

Supermicro

Supermicro SC823MTQ-R700LPB Manual de usuario

SilverStone

SilverStone RMS08 Series Manual de usuario

NI cRIO-FRC II Manual de usuario

Pickering

Pickering 65-200 Manual de usuario

Allied Telesis

Allied Telesis AT-MMCR18 Manual de usuario

Hisense

Hisense MSD6586 Manual de usuario

Cisco

Cisco Nexus 7010 Manual de instrucciones