AdvanPOS CP-2010 Series Manual de usuario

CP-2010 Series

Price Checker POS System

User Manual

Ver 1.0_2011/04/11

Before installing and operating the unit, please read this

user manual thoroughly and retain for reference.

How to Use This Manual

This manual contains information to set up and use the CP-2010. In addition, instructions are included for

added hardware, software, upgrades, and optional items.

Chapter 1 An introduction to what you find in the CP-2010 and an overview of product specifications,

appearance, and interface.

Chapter 2 Detailed installation information for the base unit and upgrades, including the CPU Module,

HDD and SD card.

Chapter 3 Mounting procedures for optional devices, such as wall mount kit.

Chapter 4 CP-2010 carry board diagrams, locations of jumpers, and connectors.

Chapter 5 Installation instructions for the MSTI video driver, audio, LAN and touch screen tools.

WARNING! Text set off in this manner indicates that failure to follow directions could result

in bodily harm or loss of life.

CAUTION: Text set off in this manner indicates that failure to follow directions could result

in damage to equipment or loss of information.

NOTE: Text set off in this manner provides important supplemental information.

Federal Communications Commission (FCC) Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

NOTE: Shielded interconnect cables and shielded AC power cables must be employed

with this equipment to insure compliance with pertinent RF emission limits

governing this device. Changes or modifications not expressly approved by the

system’s manufacturer could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired

operation.

The information in this guide is subject to change without prior notice.

The manufacturer shall not be liable for technical or editorial errors or omissions contained herein, nor for

incidental or consequential damages resulting from the furnishing, performance, or use of this material.

This manual contains information protected by copyright. No part of this manual may be photocopied or

reproduced in any form without prior written consent from the manufacturer.

The software described in this guide is furnished under a license agreement or nondisclosure agreement.

The software may be used or copied only in accordance with the terms of the agreement.

Product names mentioned herein may be trademarks and/or registered trademarks of their respective

companies.

First Edition June 2010

Patents

Certificate No.: 01328466 (ROC patent)

Patents pending (European Union, Mainland China and USA)

Precautions

1. Please read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from the AC outlet before cleaning. Do not use liquid or spray detergent

for cleaning. Use only a moistened sheet or cloth.

4. For pluggable equipment, the socket outlet should be installed near the equipment and should be

easily accessible.

5. Avoid humidity and moisture.

6. Install equipment on a stable surface.

7. Do not leave this equipment running in an enclosed or non-air-circulated environment, nor store in

temperatures above 60°C. Such conditions may damage the equipment.

8. Ventilation openings on the unit are for air circulation and protect the equipment from overheating.

DO NOT COVER THE OPENINGS.

9. Check the voltage of the power source before connecting the equipment to the power outlet.

10. Place the power cord so that it will not be stepped on. Do not place anything over the power cord.

The power cord must be rated for the product and for the voltage and current marked on the

product’s electrical ratings label. The voltage and current rating of the cord should be greater than

the voltage and current rating marked on the product.

11. All cautions and warnings on the equipment should be noted.

12. If the equipment is not used for a long time, disconnect the equipment from the power outlet to

avoid damage.

13. Never allow any liquid into ventilation openings. This could cause fire or electrical shock.

14. Never open the equipment. For safety reasons, qualified service personnel should only open the

equipment.

15. If one of the following situations may arise, get the equipment checked by qualified service

personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well or you cannot get it work according to the user manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of damage.

WARNING! Not intended for outdoor use.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with same

type, and discard used batteries according to manufacturer's instructions.

Contents

Chapter 1 Introduction..................................................................................................1

Features............................................................................................................................................. 1

Specifications...................................................................................................................................... 1

Package Contents ............................................................................................................................... 2

Base System and Options .................................................................................................................... 3

Dimensions......................................................................................................................................... 4

Connector Panel.................................................................................................................................. 5

Chapter 2 Standard Hardware and Upgrades ...............................................................6

Precautions ........................................................................................................................................ 6

Removing Scanner Module................................................................................................................... 7

Opening Bottom Covers....................................................................................................................... 8

CPU Module Replacement .................................................................................................................. 10

SATA Hard Disk Replacement............................................................................................................. 12

Chapter 3 Optional Components .................................................................................14

Wall Mount Swing Arm Kit Installation................................................................................................. 14

Chapter 4 CP-2010 Carry Board Configuration ...........................................................16

Jumper and Connector Locations........................................................................................................ 16

Connector Pin Assignments................................................................................................................ 17

Jumper Settings................................................................................................................................ 18

Chapter 5 Software Setup ...........................................................................................20

Driver Software List........................................................................................................................... 20

MSTI Graphics Driver Installation ....................................................................................................... 21

Audio Driver Installation .................................................................................................................... 22

Ethernet Driver Installation ................................................................................................................ 23

Abon Touch Screen Driver Installation ................................................................................................ 25

Chapter 1 Introduction

Features

8.9 inch TFT touch screen

Fanless operation

75mm VESA compatible installation

Ideal for price checking, verification or stock checking

IP65 sealed front touch panel

2 x COM, 4 x USB, 1 x SD

RoHS compliant

Specifications

CP-2010 System Configuration

CPU (SOC)

MSTI PMX-1000 (V or t e x 8 6M X )1GHz, 4KB SDRAM inside

Cash Memory

256K 2nd Level Cache Memory

System Memory

512MB DDR2 SDRAM on board

SD Memory

Supports 1 x SD memory card slot (optional)

HDD

1 x internal 2.5 inch 160GB SATA hard disk drive

Power

1 x external 40W 12VDC power adapter (100~240VAC, 50~60Hz, 3.3A)

OS Support

Windows®XP Pro Embedded / WEPOS®/ Windows®POS Ready 2009 /

Linux®

LCD Touch Panel

Resolution Size

8.9 inch TFT LCD / 1024 x 600

Brightness

200cd/m2

Touch Screen Type

5-wire resistive touch with RS-232 interface (optional)

I/O Ports

USB Ports

Supports 4 USB 2.0 ports for future expansion (Rear x 4)

Serial Ports

2 x external: COM1, COM3 (D-SUB) pin 9 RI/5V/12V selected by jumper

1 x internal: COM2 for touch screen

Parallel Port

1 x bi-directional parallel port (D-SUB25)

LAN Port

1 x Giga LAN (10/100/1000Mbps Base-T), RJ45 connector

Speaker

2 x internal stereo 2W speakers

A-50M Omni-directional Scanner

Light Source

650nm visible laser diode (VLD)

Depth of Field

0-200mm (UPC/EAN 100%, PCS=90%)

Scan Lines

Scan Pattern

5 directions of scan field

Scan Rate

1,200 scans per second

Minimum Bar Width

5mil @ PCS=90%

Interface

USB

A-52M 2D Imagine Scanner

Aiming Element

650nm visible laser diode (VLD)

Optical System

640 x 480 pixels (VGA type CCD)

Field of View

32.2° (horizontal); 24.5° (vertical)

Resolution

6.67 mil (PDF 417), 5mil (Code 39)

Print Contrast

30% @ UPC/EAN 100%

Image Format

BMP, TIFF, JPEG

Interface

USB

Mechanics and Environment

Construction

Plastic housing and metal

Dimensions

CP-2010 with A-50M :270(L) x 269(W) x 93(D) mm

CP-2010 with A-52M :270(L) x 269(W) x 82(D) mm

Housing Color

Red/Black, Silver/Black

Net Gross Weight

1.8 Kg

Operating Temperature

0 °C ~ 40 °C

IP65

IP65 sealed front touch panel

EMI/Safety

CE, FCC, RoHS

Package Contents

The following items come standard with the CP-2010:

CP-2010 System

Power Adaptor

Utility and Main

Board Chipset

Driver CD

AC Power Cord

Wall Mount Swing

Arm Kit (optional)

Base System and Options

Before you begin, take a few moments to become familiar with the CP-2010.

8.9 inch TFT LCD choices:

•LCD with tempered glass

•LCD with 5 wire resistive touch

Scanner module choices:

•Omni-directional Scanner Module (shown)

•2D Image Scanner Module

System Box

Internal Speaker

I/O Panel

Dimensions

(Unit: mm)

CP-2010 and A-50M Dimensions

CP-2010 and A-52M Dimensions

Tabla de contenidos

Otros manuales de Terminal táctil de AdvanPOS

AdvanPOS

AdvanPOS ABOX-110 Series Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario