AdvanceTec IDEN i60c Manual de usuario

AdvanceTec

AdvanceCommunicator™

Desktop Communication Kit

User Manual

for iDEN Condor (i60c, i90c and i95cl) and Falcon (i730, i830, i833 and i860) phone models

Contents

General ....................................................................... 1

AdvanceCommunicator™ Components ............................................ 1

System Requirements ........................................................................ 1

Hardware installation and Operation ...................... 2

Connecting the kit components ........................................................ 2

Inserting the phone into the AdvanceCommunicator™ Cradle .......... 3

LED Indicator ..................................................................................... 3

Phone Operation in AdvanceCommunicator™ .................................. 4

Placing Phone Calls ........................................................................ 4

Receiving Phone Calls .................................................................... 4

Ending a Call ................................................................................. 4

Sending Call Alert .......................................................................... 5

Placing Private and Group Calls ..................................................... 5

Volume Control ............................................................................. 5

Recording Calls ................................................................................. 5

Software installation ................................................. 6

Using the Software .................................................... 9

Application Structure ........................................................................ 9

Menus ..........................................................................................10

Status Lines ..................................................................................11

Activity Log/SMS ...........................................................................12

Dial Box/Alert Send .......................................................................13

Phone Book/History ......................................................................13

General section ............................................................................14

On-Screen Keypad ........................................................................14

First Start .........................................................................................14

Communication Initialization ............................................................15

Application Phone Book ...................................................................15

Adding Records to the Phone Book ..............................................15

Deleting Phone Book Record ........................................................18

Importing the Phone's Contacts List ..............................................18

Phone Book Contents ...................................................................19

Phone Calls ..................................................................................... 20

Dial ............................................................................................. 20

Turbo Dial .................................................................................... 20

Answering Calls ...........................................................................21

Private and Group Calls ....................................................................21

Call Alert ......................................................................................21

Making Private and Group Calls ................................................... 22

SMS Messages ................................................................................ 22

Sending SMS message to a single recipient .................................. 22

Sending SMS message to SMS Group .......................................... 23

Reading and Managing SMS Messages ........................................ 24

History ............................................................................................ 25

Displaying the Activity Log History ............................................... 25

Exporting Activity Log History ...................................................... 25

Updating the Hardware Software .................................................... 26

Troubleshooting ....................................................... 27

General

AdvanceCommunicator™ is a desktop communication kit for iDEN Condor

(i60c, i90c, and i95cl) and Falcon (i730, i830, i833 and i860) cellular phone

models, that enables easy and convenient cellular communication at home

or at the oﬃce.

AdvanceCommunicator™ will allow you:

• To make phone calls, private and group calls using the built-in speaker

phone.

• To make phone calls, private and group calls using the phone hand set.

• To charge the phone's battery.

• To record private/group calls (incoming and outgoing), and phone calls

(incoming only).

• To improve the signal strength and coverage of the cellular phone.

• To remote operate the cellular phone, using the included PC application,

allowing a convenient and enhanced way to utilize most of the phone's

features, and transforms the communication kit into a computerized

communication station.

AdvanceCommunicator™

Components

The AdvanceCommunicator™ kit includes the following components:

• Base station with a suitable cradle for iDEN Condor (i60c, i90c, and i95cl)

and Falcon (i730, i830, i833 and i860) cellular phone models

• Phone hand set

• 12VDC Power adaptor

• Local antenna

• RS232 data cable (Motorola part # NKN6544) to connect the base station

to a PC computer (for Condor phone models only)

• DB15 data cable to connect the base station to a PC computer (for

Falcon phone models only)

• Earpiece cable for phone-to-base audio connection (for Falcon phone

models only)

Optional components:

• Hand microphone (Motorola part # HMN4058A) (replacing the hand set

supplied with the kit)

• External antenna. The external antenna will improve reception and

coverage, and should comply with the compatibility standards of the

service provider.

System Requirements

• iDEN Condor or Falcon phone.

Condor Series Phones

Models i60, i90c, i95cl

SIM No. XXXXXXXXXXXX300

Falcon Series Phones

Models i730, i830, i833, i860

SIM No. XXXXXXXXXXXX310

• IBM PC compatible computer with a free serial (COM) port.

• Operating System: Windows 98/NT/2000/XP

• Electrical power connection for the communication kit.

Hardware installation

and Operation

Install the communication kit according to the following steps:

Connecting the kit components

1 Position the AdvanceCommunicator™ in a convenient location at home

or oﬃce, next to an electric power supply that will allow connecting the

power adaptor to the AdvanceCommunicator™ base.

2 Connect the plug at the end of the handset cord to the handset socket

at the back of the AdvanceCommunicator™ base.

3 Connect the local antenna to the antenna port at the back of the

AdvanceCommunicator™ base.

4 Connect the power supply adaptor included in the kit to an electrical

socket next to the AdvanceCommunicator™ base location. Connect the

plug at the end of the power adaptor cord to the power socket, located

next to the handset socket, at the back of the AdvanceCommunicator™

base.

Handset

Plug

Power Adaptor

LED

Indicator

Antenna

Port

Power

Socket

Handset

Socket Comm.

Socket

Falcon

(i730, i830, i833 and i860)

Condor

(i60, i90c and i95cl)

After connecting the AdvanceCommunicator™ base to the power

supply, the base station will perform a series of internal tests. During

these tests, the color of the LED indicator will change. At the end of the

test series, the LED indicator will display a ﬂashing red signal.

5 In order to remote operate the AdvanceCommunicator™ from a

standard PC computer, connect one end of the Data Cable to the

Communication Socket at the back of the AdvanceCommunicator™

base, and the other, to a free serial port (COM) at the back of the

computer.

Connect to computer

serial port (COM)

Connect to base

Communication socket

Data Cable for Condor Phones (i60, i90c and i95cl)

Connect to computer

serial port (COM) Connect to base

Communication socket

Data Cable for Falcon Phones (i730, i830, i833 and i860)

Note: Please note that when connecting the Data Cable for Condor

phones (i60, i90c and i95cl) to the base Communication socket,

the Motorola "M" logo is facing down.

Hardware Installation and Operation

Inserting the phone into the

AdvanceCommunicator™ Cradle

Note: When using iDEN Condor phones (i60, i90c and i95cl), remove

the logo lable on the back of the phone and replace it with the

logo lable supplied to allow connection of the phone to the

antenna in the cradle of the AdvanceCommunicator™. This will

provide access to the antenna connection socket of the phone.

1 Insert the phone into the AdvanceCommunicator™ cradle the same way

you insert it into the car kit cradle.

A Line up the connector in the cradle with the connector receptable

on the bottom of the phone.

B Press the phone down onto the cradle connector and the top of the

phone back into the cradle until it lock into place.

Note: If the logo lable covering the antenna socket at the back of the

phone is not removed, the phone may not lock into it's correct

position in the cradle, and may cause communication and

operating problems.

2 If the iDEN phone is of the Falcon series (i730, i830, i833 and i860)

and you intend to use the AdvanceTecCommunicator™ base with the

AdvanceTec Communicator application, you will need to connect the

Audio Cable (included in your communication kit) between the audio

socket of the iDEN phone and the audio socket at the left side of the

AdvanceTecCommunicator™ base.

LED Indicator

The Communicator LED Indicator, display's the following status indications:

LED Status

Flashing Red Communicator cradle is empty, No phone inserted.

Red The phone in the cradle is oﬀ. Battery charging.

Green The phone in the cradle is on.

Flashing Green Bidirectional communication mode is active.

Flashing Red and

Green

Adequate communication exists between the

Communicator and the computer via Data Cable.

Flashing Orange Changing communication mode

Hardware Installation and Operation

Phone Operation in

AdvanceCommunicator™

Once the phone is inserted into the AdvanceCommunicator™ cradle, you

will be able to operate it without the application software included.

Placing Phone Calls

To place a phone call while the phone is in the AdvanceCommunicator™:

1 Dial the phone number using the key pad, speed dial, voice, or any

other dialling option supported by your phone.

2 If the AdvanceCommunicator™ handset is resting in place, the call will

be conducted using the built-in speaker phone.

3 Talk to the general direction of the microphone, located at the front of

the AdvanceCommunicator™ base. The voice of the person on the other

side of the line, will be heard through the speaker located under the

handset.

PTT

Speaker

Microphone

4 At any point during the call, you will be able to pick up the handset and

continue as if it was a standard phone.

Note: When using the handset, you can switch to Bidirectional

communication mode by pressing the PTT button at the front

of the AdvanceCommunicator™ or on the back of handset while

picking up the handset.

The voice transfer from the speaker to the handset will take 2

seconds, during which the LED indicator will change to orange.

After the transfer is completed, the LED indicator will change to

ﬂashing green.

It is advisable to use this mode only for phone calls.

This mode is not active when the AdvanceCommunicator™ is in

remote operation by the application.

Receiving Phone Calls

To receive a phone call while the phone is in the AdvanceCommunicator™:

1 Open the phone ﬂip -or-

Press on the PTT button at the front of the AdvanceCommunicator™.

Note: If the PTT button is pressed for too long, the incoming call will

be disconnected.

2 Talk in the general direction of the microphone, located at the front of

the AdvanceCommunicator™ base. The voice of the person on the other

side of the line, will be heard through the speaker located under the

handset.

3 At any point during the call, you will be able to pick up the handset and

continue as if it was a standard phone.

Ending a Call

To end a call:

1 Press on the PTT button at the front of the AdvanceCommunicator™ for

at least 2 seconds, -or-

Press e on the phone's key pad, -or-

Close the phone's ﬂip.

Hardware Installation and Operation

Sending Call Alert

To send a call alert:

1 Select the Phonebook entry you would like to send the alert to, -or-

Insert the Private ID you wish to send the call alert.

2 To send the alert, press either the PTT button on the front of the

AdvanceCommunicator™, or the PTT button on the back of the handset.

Placing Private and Group Calls

To place private and group calls:

Using the Speaker Phone

1 Press and hold the PTT button at the front of the

AdvanceCommunicator™ and talk into the microphone.

2 After you have ﬁnished talking, release the PTT button and listen.

Using the Handset

1 Pick up the handset, press and hold the PTT button on the back of the

handset, and talk into the handset.

2 After you have ﬁnished talking, release the PTT button and listen.

Volume Control

You can control the volume level of the AdvanceCommunicator™ by using

the phone's volume control buttons located on the left side of the phone.

Recording Calls

The AdvanceCommunicator™ allows you to record phone calls as well as

private and group calls, by connecting a recording device to the 3.5mm

recording jack located on the back of the AdvanceCommunicator™ base,

just below the power socket.

Using the recording jack will allow you:

• To record incoming and outgoing private and group calls.

• To record only incoming phone calls (only the person on the other side

of the line).

Recording Jack

Software installation

This section of the manual will guide you step by step through the

installation process of the AdvanceTec Communicator application.

To download the latest version of the AdvanceTec Communicator

application go to: www.advancetec.com.

1 Before starting the install process, close all active applications.

2 To start the installation process, double click on the installer ﬁle

ATecPhoneInstall.exe.

The installer will start preparing the ﬁles needed for the installation

process, and a welcoming message will be displayed.

Please conﬁrm that all applications are terminated and press OK to

continue.

3 Select the install location.

The default location is: C:\Program Files\AdvanceTecPhone\

To change the location suggested as default,, press on Change

Directory.

At the displayed navigation window, select your location.

After you've selected the desired location, press the install button.

4 You will be prompted to select the Start Menu Program Group where a

shorcut to the AdvanceTec Communicator application will be created.

Software Installation

5 The installer will start coping the application ﬁles to the selected

location.

During this stage, a progress window will display the status of the install

process.

Note: During the installation process, you may be notiﬁed on the

existence of newer version for one or more of the installed

components.

The displayed message prompts you to select whether to save

the newer version, or replace it with the installed component.

Press Yes to keep the newer version' or No to replace it. You

can also select No to All, in order to deﬁne that each time the

installer encounters a newer ﬁle it will be replaced.

Selecting No to All may cause compatibility problems with

other installed application, therefore we advise you to always

select Yes.

6 At the end of the installation process, the installer will display a

message announcing the successful completion of the process.

The application is now ready for you to use.

7 To start the application, go to the Start button, select Programs, and

then select the AdvanceTec Communicator.

Software Installation

Creating a Shortcut on the Desktop

You can create a shortcut on the desktop or in the application bar that will

enable you a faster way of starting the application.

To create a shortcut:

1 Go to the Start button.

After the Start menu is displayed, release the mouse button.

2 Go into Programs, and select AdvaceTec Communicator.

3 Using the right mouse button, grab and drag the AdvanceTec

Communicator label from the menu to the Desktop or into the

Application Bar at the bottom.

4 Release the right mouse button, and from the popup menu that

appears, select Copy Here or Create Shortcut(s) Here.

The operating system will create the shortcut to the application in the

selected location.

Otros manuales para iDEN i60c

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios para teléfono de AdvanceTec

AdvanceTec

AdvanceTec iDEN i60c Manual de usuario

Manuales populares de Accesorios para teléfono de otras marcas

IAI

IAI CON-T Manual de usuario

BT DIVERSE 5400 Manual de usuario

Tadiran Telecom

Tadiran Telecom EMERALD ICE Manual de usuario

Musicam

Musicam FieldFone II Manual de usuario

Polycom

Polycom KIRK KIRK 4040 Hoja de especificaciones

TIPTEL

TIPTEL DECT Set 50 Manual de usuario

Panasonic

Panasonic KX-UDS124 Manual de usuario

BT BT7600 Hoja de especificaciones

Panasonic

Panasonic KX-TVP100E Manual de usuario

View

View VP-PC Manual de usuario

Baldwin Boxall

Baldwin Boxall BT8 Manual de usuario

SMC Networks

SMC Networks SMCDPCR-AP Manual de usuario

SkyLink

SkyLink SD-001 Manual de usuario

Nera

Nera ISDN Manual de usuario

MCheeta

MCheeta CT-CID803 Plus Manual de usuario

YASKAWA

YASKAWA YRC1000 Manual de usuario

Intellitouch

Intellitouch MOH-500E Manual de usuario

Viking

Viking SQRG-12 Instrucciones de uso