Advanced Technology Video VD700WDR Manual de usuario

FCC COMPLIANCE STATEMENT

CE COMPLIANCE STATEMENT

WARNING: This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

FCC INFORMATION : This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

CAUTION : Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

7. Only use attachments/accessories specified by the manufacturer.

8. Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

9. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE

PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY

SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU

ARE QUALIFIED TO DO SO.

10. Use satisfies clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power sources only.

11. Indoor use only

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert

the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure

that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

● 1/3” 960H Super HAD CCD II

● 700TVL Super High Resolution

● Day & Night function

● WDR (Wide Dynamic Range)

● High sensitivity 0.1Lux(Color), 0.00005Lux(BW, Sens-up)

● 3D Noise Reduction

● Sens-up(~x512)

● BLC, HSBLC

● Motion Detection

● Privacy Masking

● Defog

● Multi Language Support (15 languages)

● 2.8-12mm Auto Iris Vari–focal Lens

● OSD Control (Joystick)

● Vandal proof, IP66

● 3-Axis (Pan/Tilt/Rotate) Bracket

OSD MENU STRUCTURE

SETUP MENU

EXPOSURE

WHITE BALANCE

MOTION DET

3D-DNR

PRIVACY MASK

SPECIAL

SYSTEM

EXIT

WHITE BALANCE

ATW

AUTO

AWC-> SET KEY

MANUAL

EXPOSURE

ALC

ELC

DAY NIGHT

AUTO

SMART IR

DAY

NIGHT

MOTION DET

OFF

3D-DNR

OFF

PRIVACY MASK

OFF

LANGUAGE

ENGLISH, CHINESE

KOREAN, JAPANESE

FRENCH, ITALIAN

SPANISH, HEBREW

PORTUGUESE,

DUTCH, GERMAN,

POLISH, RUSSIAN,

TURKISH, ARABIC

SPECIAL

D.ZOOM

D.EFFECT

SHARPNESS

COLOR

DEFOG

SYNC

USER TITLE

LANGUAGE

SYSTEM

FACTORY RESET

EXIT

EXPOSURE

ALC/ELC

BACKLIGHT - Adjusts to view the object clearly in backlight conditions.

BLC : The backlight compensation feature helps alleviate issues of visibility

in high contrast areas. Set the BLC limit.

HSBLC : Use for masking brightness of the specific area to view the subject

more clearly. The HSBLC mode is automatically activated only in low

luminance scent

- AREA setting selects an area.

- GRAY SCALE selects a gray scale

- USER SCALE selects a bright level (5 levels)

- MASK: if setting MASK ON, the mask function is activate only when

HSBLC is automatically activated in low luminance scene.

WDR : sets Wide Dynamic Range.

BRIGHTNESS - Adjust the brightness.

If setting the brightness to lower value, the images are darkened. If setting the

brightness to higher value, the image gets bright.

Lower value(dark image) --- Higher value(bright image)

AGC - Set AGC: OFF / LOW / MIDDLE / HIGH

If the images are too dark, change the maximum AGC value to make the

images brighter.

SHUTTER - Select Shutter Speed : AUTO / OFF / A.FLK / 1/160 ~ 1/120,000

SENS-UP - OFF / AUTO(x4) / MANUAL (x2 ~ x10 ~ x512)

WHITE BALANCE

ATW (Auto Tracing White Balance)

Level : -10 ~ 0 ~ 10

AUTO

Level : -10 ~ 0 ~ 10

AWC -> SET KEY : It is able to set up the white balance automatically

to where the object is seen as desired.

MANUAL: Set the white balance options manually.

Red: Obtains optimum amount of Red gain.

Blue: Obtains optimum amount of Blue gain.

DAY / NIGHT

AUTO : Set to change the Day / Night mode automatically.

NOTE: If you set the AGC to OFF, theAUTO mode of this function is not

available and [--] mark is displayed

Burst - OFF / ON

Allows the color burst signal in monochrome mode to be removed.

Level - LOW / MIDDLE / HIGH

Dwell Time - 3 ~ 5 ~ 60 sec.

Sets the hysteresis time before switching between color/mono &

mono/color to reduce the “hunting effect”

DAY : Color only

NIGHT : Monochrome only

Burst - allows the color burst signal in monochrome to be removed.

OFF / ON

NOTE ; Select the BURST-ON or OFF when the color noise occurs on the

screen in NIGHT mode.

MOTION DETECTION

It detects the moving objects in the scent by monitoring changes in brightness

level. You can select the level of sensitivity for motion detection to 8 zones.

AREA SETUP

Sets AREA SELECTION ( 1 ~ 8 AREAS)

Sets STAGE - ON / OFF

Sets POSITION - Moves horizontal position of the mask

Moves Vertical position of the mask

Enlarges or decreases the horizontal size of the mark

Enlarges or decreases the vertical size of the mark.

SENSITIVITY : 0 ~ 50 ~ 100

0 - low sensitivity

100 - high sensitivity

DISPLAY - OFF / OUTLINE / MASK 1 / MASK 2

ALARM OUT - OFF / MESSAGE

Tabla de contenidos

Otros manuales de Cámara de seguridad de Advanced Technology Video

Advanced Technology Video

Advanced Technology Video hdg-t3x2 series Manual de usuario

Advanced Technology Video

Advanced Technology Video VDP690WDR Manual de usuario

Advanced Technology Video

Advanced Technology Video IPB3TWI Manual de usuario

Advanced Technology Video

Advanced Technology Video CLP5050I Manual de usuario

Advanced Technology Video

Advanced Technology Video CS7D37PB Manual de usuario

Advanced Technology Video

Advanced Technology Video SVD410SN Manual de usuario

Advanced Technology Video

Advanced Technology Video PERFORMANCE VD600TDNW Manual de usuario

Advanced Technology Video

Advanced Technology Video D1 Manual de usuario

Advanced Technology Video

Advanced Technology Video I PSD302TWI Manual de usuario

Advanced Technology Video

Advanced Technology Video HDCB225 Manual de usuario

Advanced Technology Video

Advanced Technology Video FD650WDR Manual de usuario

Advanced Technology Video

Advanced Technology Video IPSD302TWI Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario