8© Copyright Advanced Keys Inc. 2013. All Rights Reserved.
TACH IGNITION PROGRAMMING
Follow stepsbelow to programTachsignal forTachIgnitionMode. This functionallows automatic
START(crank)the engineby singletap thepush-startbutton.Priorto programming,check to ensure
Tach input and ignitionoutputs (ACC, ON and START) with applicableimmobilizer bypass device are
connected/programmed.ToenterTach ProgramMode, make surevehicleignition if OFFand system
is enabled with push-start button’s Status LED light is Amber.Once the system is inprogramming
mode, the Greenand Red light will flash alternatelyto indicate readyfor Tachsignal.
Entering Tach Programming Mode (New)
•If unit has neverbeenprogrammed for Tach, systemwill enter Tach Programming Modedirectly
when switched fromOFFto ACC and thento ON (Ignition)statebypressthe push-start button.
•If unit has successfullyprogrammed for Tach signal previouslyand require to enter Tach Learning
Modeagain: Switch from OFF to ACC and to ON state then press-and-hold the button.While
holding thebutton,pressthebrakepedal five times quicklyand releaseboth the brake pedaland
buttonat the5th brakepress.
Tach Programming Procedure
•Once thesystemis in programming mode,the Green and Red light will flash alternatelyand Engine
must be started within thefirst minute entering programming mode.
•Press-and hold the button to STARTand releasethe button afterengineis running. Alternatively,
usethemetalkeyto start theengine. (Themetal keymust be removed beforenext step)
•Wait (maximum4 minutes)until the enginereachidlespeed.
•Applythenreleasethebrakepedal and allow few secondsto elapsefor tachsignalto be
programmed.Removethe metalkeyif it wasused to starting engine. Enginewill keep running if
tach programmed successfully,elseit will shutdown immediatelyif failed to programor tach signal
is invalid.
Function Description
Switching between theIgnition modes (Without pressthe Brakepedal)
•TheAMBERstatuslight is ON after smart keyidentified (or moduleenabled).
•Pushthe button once for ACC and the GREEN statuslight is solid.
•Pushthe button second time for IGNITION and theGREEN statuslight blinks.
Note:If systemis never programforTACH before,it entersTACH PROGRAMMINGmode (GREEN/RED lightflash).
•Pushthe button third timeto switch OFF,AMBERstatus light will be solid,indicate system ready.
•Theoverall sequenceis: OFF> ACC > ON > OFF.
STARTthe Engine
Therearetwo starting modesdepending on jumper(JP1) setting (seeAK-PSB05 manual):
TachMode
•Pressand apply the brakeand (under anymode OFF,ACC or ON) tap button onceto START.
•Alternatively,whilein OFF state,press and hold the button for 1.5 seconds to START,without apply
thebrake.
TachlessMode
•Pressand apply the brakeand (under anymode OFF,ACC or ON), press-and-hold thebutton to
START,releasebuttonafterenginestarted.
•Alternatively,whilein OFF state,press and hold the button for 1.5 seconds without apply thebrake
to START,releasebuttonafterenginestarted.
•Aftertheenginerunning, releasethebutton first,and thenrelease thebrake.
•If manual STARTfailed to start engine, systemwill default to RUNmoderegardless. Youmust turn
OFFthesystem(pressbuttononcewithout applybrake)beforeattempt to startthe engineagain.
Turn OFF the Engine
•Pressand apply the brakethenpressand hold thebutton for 0.5 second to turnOFFthe ignition.
•Alternatively,without applythe brake,press and hold thebutton for 3 seconds to turnOFFthe
ignition.
