Advanced Instruments OsmoTECH PRO Guía de configuración

Installation & Training Guide

OsmoTECH®PRO Osmometer

MP00082 Rev 0

PCN01026

•For full installation and setup

instructions as well as detailed

instrument operation please

refer to the OsmoTECH PRO

User Manual.

Disclaimer

•Installation and Setup

•Instrument Operation

•Standards and Controls

•Calibration

•Maintenance

•Consumables and Accessories

Topics

•Step 1 –Find a location for the instrument

oEnsure adequate space

oUse a properly grounded, three-prong electrical outlet capable of supplying 0.5 amperes at 100-

240 VAC (50-60 Hz) within 5 feet of instrument placement

•Step 2 –Unpack the instrument

oUse enclosed packing list to verify all accessories

and supplies were received

oIf any items are damaged or missing, notify the carrier,

dealer, and Advanced Instruments within 24 hours

oComplete the online warranty card to register your

product at www.aicompanies.com/warranty

•Step 3 –Connecting to the printer (optional)

oYou can connect an Epson dot matrix printer to the OsmoTECH PRO.

oPurchase the printer through Advanced Instruments.

Installation and Setup

•Step 4 -Removing the ship stop

You must remove the ship stop that secures the sample cooling assembly and the sample probe

mounting block assembly.

Installation and Setup

1. Disconnect power to the instrument.

2. Unscrew and save the two small yellow

screws [A].

3. Lower both ship-jacks [B] to the lowest

position.

4. Store the screws in the storage holes [C].

5. Unscrew and save the large yellow screw [D]

6. Grasp the base of the ship stop and gently lift

it up and rotate it about 45-degrees.

7. While it’s lifted and rotated, tilt the ship stop

back about 90-degrees and gently slide out

of instrument.

8. Remove and read the warning label.

Step 7

Step 6

•Step 5 –Install turntable

oPlace turntable on a flat surface with the

numbered side visible.

oPlace a new probe wiper ring over the center

knob of the turntable.

oAlign the wiper ring so the wiper ring locating

tab is in one of the depressions provided at

turntable position 1 and position 11 and that

all positions are visible. (G)

oPlace the evaporation cover over the center

knob of the turntable with the squared shaped

open slot centered at position 1

Installation and Setup

•Step 5 –Install turntable (continued)

oGrasp the turntable by the center

knob and place it on the turntable

spindle so the flat side of the

evaporation cover fits into the

opening in the instrument cover.

oSlowly push the turntable forward

and twist slightly until it aligns and

drops down over the mating drive

spindle.

oTurn the knurled turntable locking

screw fully clockwise to lock the

turntable onto the drive spindle.

Installation and Setup

•Step 6 –Connecting to a network (optional)

•To connect the OsmoTECH PRO to a laboratory information system (LIS), OPC-UA, to a local area

network (LAN), and/or to enable the webserver, plug an Ethernet cable that connects to your

network into the Ethernet port on the back of the OsmoTECH PRO unit.

•Refer to the User Guide to configure the communication settings in the OsmoTECH PRO

software and Data management guide for more information.

Installation and Setup

•Step 7 –Powering up the instrument

•Connect the power cord to the back of the instrument and insert the plug into the power outlet.

•Turn the power switch ON.

•After a few moments, the OsmoTECH PRO Splash screen appears while the system starts up. You

will then see the Home Screen, you can initiate sample testing and view the results, Initially, the

instrument status shown in the green status banner is READY.

Installation and Setup

Splash Screen Home Screen

•Step 8 –Configuring the OsmoTECH PRO settings

•Review and/or configure the following instrument settings before using the OsmoTECH PRO.

Refer to the User Guide for instructions.

•If the unit’s language is not set appropriately for your site, change the language settings.

•If the date or time displayed on the unit is incorrect, set the current date and time.

•If desired, set up user accounts.

•If desired, assign restrictions for operator-level accounts, set the password expiration period and

configure the system to require a User ID and/or Sample ID before beginning a test.

•If desired, configure the OsmoTECH PRO to communicate with your laboratory information system

(LIS).

•If desired, configure the OsmoTECH PRO to connect to your local area network (LAN).

•If desired, set up control limits.

•If desired, enable webserver.

Installation and Setup

Otros manuales para OsmoTECH PRO

Tabla de contenidos

Otros manuales de Instrumento de medición de Advanced Instruments

Advanced Instruments

Advanced Instruments GPR-2500 Manual de usuario

Advanced Instruments

Advanced Instruments OsmoPRO Manual de usuario

Advanced Instruments

Advanced Instruments 3320 Manual de usuario

Advanced Instruments

Advanced Instruments OsmoTECH PRO Manual de usuario

Advanced Instruments

Advanced Instruments OsmoPRO Manual de usuario

Advanced Instruments

Advanced Instruments GPR-1200 Manual de usuario

Advanced Instruments

Advanced Instruments 3250 Manual de usuario

Advanced Instruments

Advanced Instruments OsmoTECH Guía de configuración

Advanced Instruments

Advanced Instruments 3250 Manual de usuario

Advanced Instruments

Advanced Instruments A2O Manual de usuario

Advanced Instruments

Advanced Instruments 4C3 Manual de usuario

Advanced Instruments

Advanced Instruments 3300 Manual de usuario

Advanced Instruments

Advanced Instruments 3300 Manual de usuario

Advanced Instruments

Advanced Instruments GPR-IN190 Manual de usuario

Advanced Instruments

Advanced Instruments GPR-1800 AIS LD Manual de usuario

Advanced Instruments

Advanced Instruments AE Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario