Advanced ICE 1469 Manual de usuario

Page 1

1469_INS_V1.1

• All labels on the product including software versions and serial numbers must not be covered, damaged or removed. This

may void the warranty on the product.

• Ensure that all left over accessories, including remote controls and cables, are kept for future use. If

replacements are required in the future they will not be provided free of charge.

• Please ensure the installation of this product will not interfere with any factory safety equipment (e.g. Airbags).

• If working with Airbags, be sure to disconnect the vehicle Battery before beginning work. This product and the following

instructions are designed for installation by a qualied 12v installer, car audio installer or auto electrician.

• Interfaces and Navigation modules must not be installed in a location where they will be exposed to extreme

temperatures including, but not limited to, installation on top of a vehicles radio, transmission tunnel or rewall.

Damaged caused by exposure to heat is not covered under warranty.

PLEASE READ BEFORE BEGINNING INSTALLATION

Installation Terms & Conditions

This is a completely plug and play system and has been designed for the following vehicles and features:

2022 - Current Ford Ranger and Everest with the Sync 4A 12 Inch Screen. This system allows for the addition of up to four (4)

cameras to the factory screen

• This product comes with a 2 year warranty against manufacturer related defects. Please read the included

warranty card and register the device on the Advanced ICE Pty Ltd website.

• This installation manual covers a range of products and vehicles.

Overview

Important Product Information

Ford Ranger/Everest Camera

Integration Installation Guide

1469

Contents

Kit Contents 2

Interaction Connection Ports 2

Required Tools for Installation 2

Interface Dip Switch Settings 2

Camera Installation Scenarios 3

Wiring Information 4

Installation Process 4

Step 1 - Dash Removal 4

Step 2 -Multimedia Interface Installation 5

Step 3 - Test and Check 5

Mode Change and Operation 6

Interface Menu Settings 7

PARK Menu 8

Trouble Shooting & FAQs 9

Handle Button (Activation Button) 9

Page 2

• Dash and Trim Removal tools

• 7mm Socket Set

• Dash Protection Tape (Recommended)

• Picking Tool

Infrared Eye (For Remote)

Interface

Mode Switch

LVDS Cable

LVDS Extension

Cable

Required Tools for Installation

Kit Contents

Please Note: You must remove power to the unit prior to making adjustments to the dipswitches.

When power is reconnected after the dip switch adjustment, the new settings will be stored into memory.

Interface Dip Switch Settings

Interaction Connection Ports

Dip SW: 1 2 3 4 5 6 7 8 9 10

UP/OFF -- OFF - OFF OFF - OFF - OFF

ON/DOWN ON ON -ON - - ON - ON -

Remote

Mounting Bracket

(6 x screws included)

LVDS

Extension

Cable

LVDS

Cable

90 Degree Programming

Ports

Not Used

Dipswitches

(see page 2) Connect

Power/CAN

T Harness Camera

AV Cable

Connection

Not Used

May be required

for product Setup

(see page 6)

Not Used

Power & CAN T

Harness Video Input Harness

WA7058

- RCA Y Adapter

Page 3

Camera Installation Scenarios

SINGLE CAMERA INSTALLATION

Connect to Camera RCA

R - CAM

F - CAM

DUAL CAMERA INSTALLATION

R - CAM

F - CAM

Connect to Driving Forwards Caravan Camera

Connect to Reverse Caravan Camera

Page 4

Wiring Information

Description Used For

ACC Power Wire This wire can be used to power up your

cameras

Video Input (F CAM) Connect Camera video signal for cameras

that can be viewed when driving

Video Input (R CAM)

Connect Camera video signal for cameras

that can be viewed when in reverse using

RTC (see user manual)

Video Input

(LET CAM)

Second or Left Camera video input that can

be viewed when driving

Video Input

(RGT CAM)

Third or Right Camera video input that can

be viewed when driving

Highbeam Output

This is a CAN-Bus generated Highbeam

output for use when installing Spot Lights or

Light Bars

ACC

LEFT CAM

LR-PWR

RIGHT CAM

R - CAM

F - CAM

Installation Process

PLEASE READ BEFORE CONTINUING

We strongly recommend taking appropriate steps (i.e. Masking Tape) to protect the factory screen, dash, steering

wheel and console. We also recommend covering the upholstery on the front seats.

Step 1 - Dash Removal

• Scan or click on the QR Code to watch the video on how to perform the dash removal in order to prepare for

the installation.

This video is a guide only and does not represent the exact process

on all Ranger & Everest Year/Model Variants.

Page 5

Step 2 -Multimedia Interface Installation

Please watch the entire video before beginning the installation.

If you are not comfortable with the technical nature of this installation,

we recommend taking it to a 12 volt professional to perform the installation for you.

• Scan or click on the QR Code to watch the video on how to prepare the product for installation and how to

connect it to the vehicle.

• Scan or click on the QR Code to watch the video on how to prepare the product for installation and how to

connect it to the vehicle.

• Before putting the vehicle back together we recommend making the following checks to make sure everything is

operating correctly

Check the factory system is powering on and working correctly

Check the Reverse Camera is working

Activate the Caravan Camera in Drive or Park (See Mode Change Instructions)

Check RTC Function is Working in Reverse (See Mode Change Instructions)

• When putting the Dash back together, remember to reconnect all disconnected plugs and make a test phone call

to ensure everything is functioning correctly

Ambient Light (if installed)

2 x USB Hub

Wireless Charging Pad (if installed)

Step 3 - Test and Check

Page 6

When Driving

Long Press the OK button which is the systems Default Activation button to turn on the

Camera Source. If additional camera inputs have been activated, then additional long press of

this button will cycle through the camera inputs.

In Reverse

Long Press the OK button to switch from the vehicles factory reverse camera to the Camera

input of our interface.

These buttons can be used instead of the OK button to activate video sources.

(See Interface Menu Settings)

Short Press the OK button to return to the factory screen and switch o the camera source.

If the camera system stops responding a Longer 5 second Press of the Menu Button (Red) will

reset the camera system.

Scan or Click on the QR Code to see how the system operates

Mode Change and Operation

Page 7

Interface Menu Settings

In order to access the menu’s of our interface you will need to connect the Infrared

Eye to the interface and use the remote control.

1. Activate the camera interface so it is on the camera input

(a camera does not need to be reconnected)

2. Point the Remote at the Infrared Eye and Long Press the Red Arrow Button

to access the menus

3. Use the Arrow Buttons on the Remote to navigate the menus and the OK

Button to conrm a change.

Do not make any other changes other than the ones listed below.

Climate Adjustments

When the Camera source is activated and one of the highlighted climate control functions are

adjusted, the system will automatically switch back to display the adjustment. After 5 seconds

from the last adjustment made, the system will automatically switch back to the camera

source.

Page 8

PARK Menu

In the Park Menu the following changes can be made

1. Side Type

Chne this from IRE DET to C -DET to enble the Left nd/or Riht Cmer inputs to be

ctivted with the crs Indictor.

Please note:

• Left and/or Right Camera’s need to be activated for this to function - see next step

• RTC (Camera in Reverse) function needs to be activated before the camera’s will turn on with the

indicators.

2. Side Function

This menu allows you to activate additional camera inputs

• CAM OFF - Default

One Camera input activated - This camera is always activated

• CAM2 (R)

This adds a second camera input visible when driving forwards and allows the right camera to be turned on by

indicator

• CAM3 (L)

This activates a second camera input and allows the left camera to be turned on by indicator

• CAM ALL

This activates all three camera inputs and allows the left and right camera to be turned on by the indicators

IMAGE

PARK

FUNC

UTIL

INFO

PAS TYPE

PAS SETUP

REAR TYPE

AUTO FCAM

SIDE TYPE

SIDE FUNC

NOT USED

CAN

OFF

WIRE DET

CAM OFF

Page 9

Trouble Shooting & FAQs

Q- After Installation the factory screen is blank and has not image.

A- Check the following:

• Ensure the LVDS Connections are correct as per the image.

• Ensure the dipswitches are set correctly

Handle Button (Activation Button)

Under the UTIL menu you can change the button on the steering wheel that is used to activate the camera source.

The options include the following:

1. OK - Default

2. PHONE - Phone button*

3. BACK - Return button

If the Phone button is selected as the activation button, then please note that if you are on a phone

call it will be ended if you long press the Phone button to activate the camera.

IMAGE

PARK

FUNC

UTIL

INFO

RESET ALL

HANDLE BTN

ACC OUT

HBEAM

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Advanced ICE

Advanced ICE

Advanced ICE 1435 Manual de usuario

Advanced ICE

Advanced ICE 1324-1 Manual de usuario

Advanced ICE

Advanced ICE 1409-2 Manual de usuario

Advanced ICE

Advanced ICE NAV-FCA-P2 Manual de usuario

Advanced ICE

Advanced ICE 1435-1 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario