ADTRAN TRACER 4x06 Manual de referencia

Converting the Frequency Plan of a TRACER 4x06(L2) System

Introduction

TRACER 4x06 systems are shipped from the factory with the frequency plan programmed as Plan A or

Plan B. Each wireless link must contain a Plan A radio on one end and a Plan B on the other. A frequency

plan conversion may be performed in the field, but should only be attempted if absolutely necessary and

must always be performed by qualified personnel. This document outlines the procedure for changing the

frequency plan of a List 2 (L2) TRACER 4x06 system (TRACER 4106 - P/N 12804106L2A/B or

TRACER 4206 - P/N 12804206L2A/B).

Prerequisite Procedures

The current frequency plan configuration is listed on a label located on the rear panel of the unit (near the

Antenna connector). Record the current configuration before beginning this procedure.

Tools and Materials Required

• 5/16” Torque wrench (8 in-lbs)

• 3/16” nut driver

• Phillips-head screw driver

Disconnect all cables attached to the TRACER 4x06 system (including power, data,

terminal RS-232, etc.) before performing this procedure.

Do not attempt to perform the conversion without the proper tools (see list below). Using

improper tools will damage the unit.

Electronic equipment can be damaged by static electrical discharge. Before handling

equipment, put on an antistatic discharge wrist strap to prevent damage to components.

Place equipment in antistatic packing material when transporting or storing. When

working on equipment, always place it on an approved antistatic mat that is electrically

grounded.

TRACER 4x06(L2) Frequency Conversion Document

1. Remove the screws from the chassis cover using a Phillips-head screwdriver (see Figure 1).

Figure 1. Removing the Cover Screws (TRACER 4x06)

2. Remove the nuts on either side of the RS-232 connector (on the rear panel of the unit) using the 3/16”

nut driver (see Figure 2).

Figure 2. Removing the RS-232 Nuts

3. Carefully slide the cover toward the back of the unit until the front edge of the cover is disconnected

from the front of the unit. Lift the cover off and set aside.

Perform the steps below in the order listed.

Remove all connected mounting brackets before attempting to remove the unit cover.

TRACER 4x06(L2) Frequency Conversion Document

4. Verify the current frequency plan configuration. To verify the plan, check the connections between the

J connectors (located on the board and labeled J1 and J2) and the Chan connectors (located on the

diplexer). The Chan connectors are labeled 2421 (Chan 1) and 2462 (Chan 2) for most TRACER 4106

systems and CH1 and CH2 for most TRACER 4206 systems. The following table outlines the

connections for Plan A and B.

Click to see a digital image of the J connectors or the Chan connectors.

5. Using the torque wrench, disconnect both cables from the Chan connectors on the diplexer. Do not

attempt to disconnect the J connectors (located on the board) as this will cause damage. Click here for

a digital picture of this step.

6. Carefully flex the cables to swap the connections. Be careful with the RF cables, making sure that the

minimum bend radius of the cable is greater than 0.75"; bends and loops smaller than a quarter will

cause the RF cable to break. Use the wiring guidelines in Figure 3 and Figure 4 on page 4 for help with

wire placement. Click here for a digital picture of this step.

Figure 3. TRACER 4106 Cable Routing Diagrams

TRACER 4x06

PLAN CHAN 1 CHAN 2

AJ2 J1

BJ1 J2

Allowing the RF cables to sit on the processor and radio boards (green) could cause

damage to the boards; keep the RF cables off the boards while re-routing them. Click here

for a digital picture of this mistake.

ANT

PLAN B

J1 CABLE OVER ANT CABLE

2421

2462

ANT

PLAN A

J2 CABLE UNDER J1 CABLE

2421

2462

TRACER 4x06(L2) Frequency Conversion Document

Figure 4. TRACER 4206 Cable Routing Diagrams

7. Use the torque wrench to reconnect the RF cables to the Chan connectors. Tighten the cables by

turning clockwise until you hear a click from the wrench. DO NOT overtighten connectors as this will

cause the RF cable to break. The TRACER 4x06 system will not operate properly with broken RF

cables.

8. Reinstall the cover and carefully tighten all screws.

9. Change label on back of the unit to reflect the Plan change.

J1 J2

CH2 CH1

PLAN B

J1 J2

CH2 CH1

PLAN A

>> BACK

Otros manuales de Hardware de red de ADTRAN

ADTRAN

ADTRAN DSU/CSU Manual del producto

ADTRAN

ADTRAN BR1 Manual de usuario

ADTRAN

ADTRAN Total Access 374 Manual del producto

ADTRAN

ADTRAN OC-12 Manual de usuario

ADTRAN

ADTRAN HDSL4 Manual de instrucciones

ADTRAN

ADTRAN BVL3ADJD Manual de usuario

ADTRAN

ADTRAN DSX 1 Manual de usuario

ADTRAN

ADTRAN NetVanta SHDSL Network Interface Module Manual de usuario

ADTRAN

ADTRAN FXO+ DUAL VOICE Manual de usuario

ADTRAN

ADTRAN DSU IV ESP Manual de usuario

ADTRAN

ADTRAN Total Access 362R Manual del producto

ADTRAN

ADTRAN 1200312L5 Manual de usuario

ADTRAN

ADTRAN 6540 Manual de instrucciones

ADTRAN

ADTRAN 24-Port DSLAM Access Module IADSL Module Manual de usuario

ADTRAN

ADTRAN 1202803L1 Manual de usuario

ADTRAN

ADTRAN P/N 1204011L1 Manual de servicio

ADTRAN

ADTRAN 1442703PG2 Manual de usuario

ADTRAN

ADTRAN NetVanta 7000 Series Manual de usuario

ADTRAN

ADTRAN 1442300G1 Manual de usuario

ADTRAN

ADTRAN Total Access 372E Manual de usuario

ADTRAN

ADTRAN TRACER 4205 Manual de usuario

ADTRAN

ADTRAN BR10 Manual de usuario

ADTRAN

ADTRAN DS3 MX Manual de usuario

ADTRAN

ADTRAN DSU III TDM Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario