ADTRAN TA 900 Manual de usuario

Quick Configuration Guide (QCG)

TA 900/900e E&M Wink Trunk Quick Start Guide

Overview

This Configuration Guide explains how to configure a T1 port on the Total Access

900/900e for a Robbed Bit Signaling T1 to be connected to a PBX or other CPE

device that requires an E&M WInk connection.

Requirements & Limitations

In the TA 900 series, only T1 port 0/2 can be used for an E&M Wink connection.

In the TA 900e series, T1 ports 0/3 and 0/4 can be used for E&M Wink

connections.

Web Interface Configuration

Configuring the Local Dialing Type

First, we must set the Local Dialing Type to 7 or 10 digits. To do this, begin by

clicking on ‘Dial Plan’ under ‘Voice’.

Then, select the appropriate 7 or 10 Digit Dialing for local calls and click on

‘Apply’.

Configuring the T1 Interface

To begin configuring the T1 interface, click on ‘Physical Interfaces’ under

‘System’.

Next, click on ‘t1 0/2’ under the ‘Physical Interfaces’ list.

This will take you to the ‘T1 0/2’ Interface Configuration page. In the Description

box, you have the option of entering a label for the interface.

Next, you will want to check the ‘Enable’ box to enable the interface.

Click ‘Apply’ to apply the configuration above.

Since this will be an RBS interface, we want to reserve the T1 0/2 interface for an

RBS trunk by selecting ‘Reserve for RBS Trunks’ in the drop-down menu.

Specify the appropriate DS0 range using the drop-down boxes. When finished,

click the ‘Add’ button.

Note: This will create a specific TDM group for each DSO selected in the range.

If this is not the desired behavior, changes will need to be made via the

Command Line Interface. Go to the section titled ‘Configuring the T1 Interface’

under the ‘Command Line Interface Configuration’ for more information.

Configuring the RBS Trunk

First, we will configure a Codec List to be used by the RBS trunk. To do this,

click on ‘Codec Lists’ under ‘Voice’.

Click on the ‘Add New Codec List’ button to create a new Codec List.

Specify a name for the Codec List in the ‘Codec List Name’ field.

Specify the primary Codec to be used as ‘Codec #1’ and the secondary Codec to

be used as ‘Codec #2’. Once those are configured, click on ‘Apply’.

Next, we need to create the RBS trunk. To do this, start by clicking on ‘Trunk

Accounts’ under the ‘Voice’ tab.

Give the Trunk a name if you’d like.

Make sure that ‘Type’ is set to T1-RBS.

As of the current revision, the ‘Supervision’ can only be set to ‘E&M Wink’ and

the ‘Role’ can only be set to ‘Network’. When finished, click on ‘Add’.

You can specify an optional trunk description in the ‘Trunk Name’ field.

You will probably want to un-check the ‘Reject External’ box to allow trunk-to-

trunk calls to work properly. Un-checking this box allows the RBS trunk to accept

calls from other trunks that may be configured (i.e. PRI or SIP). This command is

necessary for deployments where more than one trunk is being used (i.e. a SIP

trunk and an RBS trunk to the CPE).

If DTMF digits are needing to be sent to the CPE when an inbound call is made,

Direct Inward Dialing will need to be configured by checking the DID box.

If Direct Inward Dialing is enabled, you need to specify the number of digits to be

sent to the CPE on an inbound call.

The way that a DS0 is allocated for a call can be configured to be ‘Linear’ or

‘Circular’. With ‘Linear’ the lowest available DS0 is used. With ‘Circular’, the

next DS0 in line is used.

To assign DS0s to the RBS trunk, begin by clicking on the ‘Assign DS0s’ button.

This will bring up a new window where particular DS0s can be added to the RBS

Trunk. In this example, we want to connect all 24 DS0s to the trunk so we select

all of the T1 0/2 DS0s by clicking on the check box under the ‘Add’ column for

each one. When finished, click the ‘Add DS0s’ button.

Click ‘Apply’ to apply the configuration changes.

The last step is to create a trunk group for the RBS trunk. To start this process,

click on ‘Trunk Groups’ under the ‘Voice’ tab.

Give the Trunk Group an appropriate name using the ‘Group Name’ field and

then click ‘Add’.

You can give the Trunk Group a description to help keep track of the

configuration.

To add the RBS trunk to the trunk group, click on the ‘Add Members’ button.

A new window will open with the available trunk accounts. Check the box under

the ‘Add?’ column for the appropriate trunk account and then click on the ‘Add

Selected Trunks’ button.

To configure calls to certain numbers to route out of the RBS trunk, click on the

‘Configure Advanced Templates’ button under the Call Templates section.

A good rule of thumb is to be specific with trunks going to CPE devices and be

general when creating call routing rules with trunks going to the PSTN/SIP

network. In this example, we have been assigned the number 256-555-1000 by

the SIP provider and want to route that number out the RBS trunk. To do this,

add the specific number to the ‘Template’ box and assign a ‘Cost’ of 0. When

finished, click on ‘Add’.

Once the Permit Template(s) have been verified, click on the ‘Return to Trunk

Group Config’ button.

Click on the ‘Apply’ button to apply the configuration changes.

Always remember to save your changes by clicking on ‘Save’ at the top of the

Web GUI.

Command Line Interface Configuration

An RBS trunk is configured over a T1 interface. To begin, we must setup the T1

interface correctly and then connect it to the RBS trunk.

Note: The configuration parameters used in the examples are for instructional

purposes only. Please replace all underlined entries (i.e. example) with your

specific parameters to configure your application.

Configuring the T1 Interface

First, you must create a TDM group. The following example creates a TDM

group of 24 DS0s (Channels 1-24 at 64kbps each) on the T1 connection.

Note: The Web Configuration will create 24 individual TDM groups each

comprised of one DS0. This is necessary if a particular DID needs to go to a

particular channel on the RBS Trunk (Multiple voice trunk accounts and trunk

groups are needed for this functionality). If this is not necessary and any DID

can go down any channel, only one TDM group is needed when configuring via

the CLI (This situation is used for the Web Configuration and the Command Line

Interface Configuration in this guide).

(config)#interface t1 0/2

(config-t1 0/2)#description RBS T1 to PBX

(config-t1 0/2)#tdm-group 1 timeslots 1-24 speed 64

(config-t1 0/2)#no shutdown

(config-t1 0/2)#exit

Configuring the RBS Trunk

Step 1:

First, it is a good idea to create an appropriate Codec List to be used by the PRI

trunk. In a Codec List, you can specify which codec should be prioritized by the

trunk when negotiating the call setup. In this example, a Codec List named

‘Trunk’ is going to be configured to use G.729 as the primary codec and G.711

as the secondary codec.

(config)#voice codec-list Trunk

(config-codec)#codec g729

(config-codec)#codec g711ulaw

(config-codec)#exit

Step 2:

Next, create the RBS voice trunk using the ‘voice trunk’ command and specifying

the type as ‘t1-rbs supervision wink role network’. An optional description can be

given to the trunk as well using the ‘description’ command. The command ‘no

reject-external’ allows the RBS trunk to accept calls from other trunks that may

be configured (i.e. PRI or SIP). This command is necessary for deployments

where more than one trunk is being used (i.e. a SIP trunk and a PRI/RBS trunk to

the CPE). Finally, connect the voice trunk to a TDM group on a T1 interface

using the ‘connect’ statement. The ‘did digits-transferred’ command specifies

how many DNIS digits will be sent to the CPE device on an inbound call.

(config)# voice trunk T02 type t1-rbs supervision wink role network

(config-T02)#description "RBS T1 to PBX"

(config-T02)#no reject-external

(config-T02)#connect t1 0/2 tdm-group 1

(config-T02)#did digits-transferred 10

Step 3:

Since this is a voice trunk and not a voice user, a voice grouped trunk will need

to be configured to specify which numbers should be routed out the RBS trunk.

A good rule of thumb is to be specific with trunks going to CPE devices and be

general when creating call routing rules with trunks going to the PSTN/SIP

network. In this example, we have been assigned the number 256-555-1000 by

the SIP provider and want to route that number out the RBS trunk. We do this by

adding an ‘accept’ entry for the specific number.

(config)#voice grouped-trunk "RBS T1 TO PBX"

(config-RBS T1 TO PBX)#trunk T02

(config-RBS T1 TO PBX)#accept 256-555-1000 cost 0

Step 4:

Once everything is configured correctly, you will want to save your changes.

(config)#exit

#copy running-config startup-config

Example Configuration

interface t1 0/2

description RBS T1 to PBX

tdm-group 1 timeslots 1-24 speed 64

no shutdown

voice codec-list Trunk

codec g729

codec g711ulaw

voice trunk T02 type t1-rbs supervision wink role network

description "RBS T1 to PBX"

no reject-external

did digits-transferred 10

connect t1 0/2 tdm-group 1

voice grouped-trunk "RBS T1 TO PBX"

no description

trunk T02

accept 256-555-1000 cost 0

If you experience any problems using your ADTRAN product, please contact ADTRAN

Technical Support.

DISCLAIMER

ADTRAN provides the foregoing application description solely for the reader's consideration

and study, and without any representation or suggestion that the foregoing application is or

may be free from claims of third parties for infringement of intellectual property rights,

including but not limited to, direct and contributory infringement as well as for active

inducement to infringe. In addition, the reader's attention is drawn to the following

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de ADTRAN

ADTRAN

ADTRAN NetVanta 900 Series Manual

ADTRAN

ADTRAN Total Access 362R Manual de usuario

ADTRAN

ADTRAN BVL3ADJD Manual de usuario

ADTRAN

ADTRAN Total Access 544R Manual de usuario

ADTRAN

ADTRAN 4202023L1 Manual de usuario

ADTRAN

ADTRAN NetVanta 6360 Manual de usuario

ADTRAN

ADTRAN 1442823F1 Manual de usuario

ADTRAN

ADTRAN DS3 NIU3 PM Manual de instrucciones

ADTRAN

ADTRAN Total Access 850 Manual de instrucciones

ADTRAN

ADTRAN 1200630L1 Manual de usuario

ADTRAN

ADTRAN Total Access 300 Series Manual del producto

ADTRAN

ADTRAN ATLAS 550 Manual de usuario

ADTRAN

ADTRAN 3.125 Gigabit Ethernet Manual de usuario

ADTRAN

ADTRAN DSU III TDM Manual de usuario

ADTRAN

ADTRAN NetVanta Analog Modem Dial Backup Interface... Manual de usuario

ADTRAN

ADTRAN DSX 1 Manual de usuario

ADTRAN

ADTRAN jobAid NetVanta 838T Manual de usuario

ADTRAN

ADTRAN 200410L1 Manual de usuario

ADTRAN

ADTRAN SFP+ Manual de usuario

ADTRAN

ADTRAN 6540 Manual de instrucciones

ADTRAN

ADTRAN Dual T1/PRI Manual de usuario

ADTRAN

ADTRAN 24-Port DSLAM Access Module IADSL Module Manual de usuario

ADTRAN

ADTRAN 1200184L1 Manual de usuario

ADTRAN

ADTRAN HTU-C Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario