ADTRAN NxT1 HSSI/V-35 Manual de usuario

NxT1 HSSI/V.35 Module

User Manual

Part Number 1200771L1

61200771L1-1A

March 2002

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

(256) 963-8000

Printed in U.S.A.

Safety Instructions

When using your telephone equipment, please follow these basic safety precautions to reduce the risk

of fire, electrical shock, or personal injury:

1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in

a wet basement, or near a swimming pool.

2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a

remote risk of shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not

dispose of batteries in a fire. They may explode. Check with local codes for special disposal

instructions.

Save These Important Safety Instructions

Notes provide additional useful information.

Cautions signify information that could prevent service interruption.

Warnings provide information that could prevent damage to the equipment or

endangerment to human life.

Affidavit Requirements for Connection to Digital Services

• An affidavit is required to be given to the telephone company whenever digital terminal equipment

without encoded analog content and billing protection is used to transmit digital signals containing

encoded analog content which are intended for eventual conversion into voiceband analog signals

and transmitted on the network.

• The affidavit shall affirm that either no encoded analog content or billing information is being

transmitted or that the output of the device meets Part 68 encoded analog content or billing

protection specifications.

• End user/customer will be responsible for filing an affidavit with the local exchange carrier when

connecting unprotected customer premise equipment (CPE) to 1.544 Mbps or subrate digital

services.

Until such time as subrate digital terminal equipment is registered for voice applications, the affidavit

requirement for subrate services is waived.

Affidavit for Connection of Customer Premises Equipment

to 1.544 Mbps and/or Subrate Digital Services

For the work to be performed in the certified territory of ___________________ (telco name)

State of ________________

County of ________________

I, _______________________ (name), ____________________________________ (business

address),

____________________ (telephone number) being duly sworn, state:

I have responsibility for the operation and maintenance of the terminal equipment to be

connected to 1.544 Mbps and/or ________ subrate digital services. The terminal equipment to be

connected complies with Part 68 of the FCC rules except for the encoded analog content and

billing protection specifications. With respect to encoded analog content and billing protection:

( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the

digital CPE with respect to analog content and encoded billing protection information

continuously complies with Part 68 of the FCC Rules and Regulations.

( ) The digital CPE does not transmit digital signals containing encoded analog content or billing

information which is intended to be decoded within the telecommunications network.

( ) The encoded analog content and billing protection is factory set and is not under the control of the

customer.

I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment,

maintenance, and adjustment of the encoded analog content and billing information has (have)

been trained to perform these functions by successfully having completed one of the following

(check appropriate blocks):

( ) A. A training course provided by the manufacturer/grantee of the equipment used to encode

analog signals; or

( ) B. A training course provided by the customer or authorized representative, using training

materials and instructions provided by the manufacturer/grantee of the equipment used to

encode analog signals; or

( ) C. An independent training course (e.g., trade school or technical institution) recognized by the

manufacturer/grantee of the equipment used to encode analog signals; or

( ) D. In lieu of the preceding training requirements, the operator(s)/maintainer(s) is (are) under the

control of a supervisor trained in accordance with _________ (circle one) above.

I agree to provide ______________________ (telco’s name) with proper documentation to

demonstrate compliance with the information as provided in the preceding paragraph, if so

requested.

_________________________________Signature

_________________________________Title

_________________________________ Date

Transcribed and sworn to before me

This ________ day of _______________, _______

_________________________________

Notary Public

My commission expires:

_________________________________

FCC regulations require that the following information be provided in this manual:

1. This equipment complies with Part 68 of FCC rules. On the back of the equipment housing is

a label showing the FCC registration number and ringer equivalence number (REN). If

requested, provide this information to the telephone company.

2. If this equipment causes harm to the telephone network, the telephone company may

temporarily discontinue service. If possible, advance notification is given; otherwise,

notification is given as soon as possible. The telephone company will advise the customer of

the right to file a complaint with the FCC.

3. The telephone company may make changes in its facilities, equipment, operations, or

procedures that could affect the proper operation of this equipment. Advance notification and

the opportunity to maintain uninterrupted service are given.

4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and

warranty information. The telephone company may require this equipment to be disconnected

from the network until the problem is corrected or it is certain the equipment is not

malfunctioning.

5. This unit contains no user-serviceable parts.

6. An FCC compliant telephone cord with a modular plug is provided with this equipment. This

equipment is designed to be connected to the telephone network or premises wiring using an

FCC compatible modular jack, which is Part 68 compliant.

7. The following information may be required when applying to the local telephone company for

leased line facilities:

8. The REN is useful in determining the quantity of devices you may connect to your telephone

line and still have all of those devices ring when your number is called. In most areas, the sum

of the RENs of all devices should not exceed five. To be certain of the number of devices you

may connect to your line as determined by the REN, call your telephone company to

determine the maximum REN for your calling area.

9. This equipment may not be used on coin service provided by the telephone company.

Connection to party lines is subject to state tariffs. Contact your state public utility

commission or corporation commission for information.

Service Type SOC REN FIC USOC

1.544 Mbps–SF 04DU9.BN N/A 6.0N RJ-48C

SF and B8ZS 04DU9.DN

ESF 04DU9.1KN

ESF and B8ZS 04DU9.1SN

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio frequencies.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

Industry Canada Compliance Information

Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the

“IC:” in front of the certification/registration number) signifies that the Industry Canada technical

specifications were met.

Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the

documentation or on the product labeling/markings. The REN assigned to each terminal device

indicates the maximum number of terminals that can be connected to a telephone interface. The

termination on an interface may consist of any combination of devices subject only to the requirement

that the sum of the RENs of all the devices should not exceed five (5).

Canadian Emissions Requirements

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,”

ICES-003 of the Department of Communications.

Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux appareils

numeriques de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numeriques,”

NMB-003 edictee par le ministre des Communications.

Warranty and Customer Service

ADTRAN will replace or repair this product within five years from the date of shipment if it does not

meet its published specifications or fails while in service. For detailed warranty, repair, and return

information refer to the ADTRAN Equipment Warranty and Repair and Return Policy Procedure.

Return Material Authorization (RMA) is required prior to returning equipment to ADTRAN.

For service, RMA requests, or further information, contact one of the numbers listed at the end of this

section.

LIMITED PRODUCT WARRANTY

ADTRAN warrants that for five years from the date of shipment to Customer, all products

manufactured by ADTRAN will be free from defects in materials and workmanship. ADTRAN also

warrants that products will conform to the applicable specifications and drawings for such products, as

contained in the Product Manual or in ADTRAN's internal specifications and drawings for such

products (which may or may not be reflected in the Product Manual). This warranty only applies if

Customer gives ADTRAN written notice of defects during the warranty period. Upon such notice,

ADTRAN will, at its option, either repair or replace the defective item. If ADTRAN is unable, in a

reasonable time, to repair or replace any equipment to a condition as warranted, Customer is entitled to

a full refund of the purchase price upon return of the equipment to ADTRAN. This warranty applies

only to the original purchaser and is not transferable without ADTRAN's express written permission.

This warranty becomes null and void if Customer modifies or alters the equipment in any way, other

than as specifically authorized by ADTRAN.

EXCEPT FOR THE LIMITED WARRANTY DESCRIBED ABOVE, THE FOREGOING

CONSTITUTES THE SOLE AND EXCLUSIVE REMEDY OF THE CUSTOMER AND THE

EXCLUSIVE LIABILITY OF ADTRAN AND IS IN LIEU OF ANY AND ALL OTHER

WARRANTIES (EXPRESSED OR IMPLIED). ADTRAN SPECIFICALLY DISCLAIMS ALL

OTHER WARRANTIES, INCLUDING (WITHOUT LIMITATION), ALL WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SOME STATES DO

NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, SO THIS EXCLUSION MAY

NOT APPLY TO CUSTOMER.

In no event will ADTRAN or its suppliers be liable to Customer for any incidental, special, punitive,

exemplary or consequential damages experienced by either Customer or a third party (including, but

not limited to, loss of data or information, loss of profits, or loss of use). ADTRAN is not liable for

damages for any cause whatsoever (whether based in contract, tort, or otherwise) in excess of the

amount paid for the item. Some states do not allow the limitation or exclusion of liability for incidental

or consequential damages, so the above limitation or exclusion may not apply to Customer.

Otros manuales para NxT1 HSSI/V-35

Tabla de contenidos

Otros manuales de Hardware de red de ADTRAN

ADTRAN

ADTRAN ATLAS 800 Series Module QUAD E1 Guía del usuario

ADTRAN

ADTRAN 1200 Series Manual de usuario

ADTRAN

ADTRAN DSU III AR Manual de usuario

ADTRAN

ADTRAN E1 Manual de instrucciones

ADTRAN

ADTRAN CenturyLink C424G Manual de usuario

ADTRAN

ADTRAN TSU 120 Manual de usuario

ADTRAN

ADTRAN TRACER 4305 Manual de usuario

ADTRAN

ADTRAN JOBAID T200 IDSL Manual de usuario

ADTRAN

ADTRAN BR1 Manual de usuario

ADTRAN

ADTRAN D4 FT1 DP Manual de usuario

ADTRAN

ADTRAN T200 HTU-R Manual de instrucciones

ADTRAN

ADTRAN Total Access 372 Manual del producto

ADTRAN

ADTRAN BR1/10 PAU Manual de instrucciones

ADTRAN

ADTRAN NETVANTA 6355 Manual de usuario

ADTRAN

ADTRAN NetVanta 1224 Manual de instrucciones

ADTRAN

ADTRAN ISU 2X64 Manual de usuario

ADTRAN

ADTRAN 6540 Manual de instrucciones

ADTRAN

ADTRAN Total Access 300 Series Manual de usuario

ADTRAN

ADTRAN FXS/DPO/PLAR 1109403L2 Manual de instrucciones

ADTRAN

ADTRAN HDSL4 Manual de instrucciones

ADTRAN

ADTRAN Total Access 1500 Total Reach DDS-DP Manual del producto

ADTRAN

ADTRAN NetVanta 1531 Series Manual

ADTRAN

ADTRAN Total Access 5006 Manual de usuario

ADTRAN

ADTRAN NetVanta 1700801G1 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario