ADTRAN NetVanta 1700801G1 Manual de usuario

NetVanta 3G CDMA Network Interface Module (NIM) P/N 1700801G1, 1700802G1

ANT1 ANT2

3G NIM (CDMA)

WWAN RSSI

1xRTT EVDO

SPECIFICATIONS

Wireless Technologies 1xRTT

1xEV-DO Revision 0

1xEV-DO Revision A

Frequency Bands Band Class 0 (Cellular 800 MHz)

Band Class 1 (PCS 1.9 GHz)

Compliance FCC Part 15, Class A

FCC Parts 2, 22, 24

UL/CUL 60950-1

RSS 102

IC ES-003

RSS 129/133

RSS 132/133

Physical Dimensions: 2.75-inch W x 4.25-inch D

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Visit www.adtran.com/3G for details on NetVanta platforms

supporting the NetVanta 3G CDMA NIM.

This device has been designed to operate with the antennas

listed below, and having a maximum gain of 2 dB. Antennas not

included in this list or having a gain greater than 2 dB are

strictly prohibited for use with this device. The required antenna

impedance is 50 ohms.

Proper antennas are:

Pulse/Larson Dipole Antenna

Part Number: SPDA24850/1900

To reduce potential radio interference to other users, the

antenna type and its gain should be chosen so that the

equivalent isotropically radiated power (e.i.r.p.) is not more

than that permitted for successful communication.

INSTALLATION INSTRUCTIONS

1. Remove power from the base unit.

2. Slide the option module into the option slot until the module is

firmly seated against the chassis.

3. Secure the pins at both edges of the module.

4. Place either of the two antennas directly onto the antenna port

labeled ANT1 on the rear panel.

5. Using the thumb screws only, carefully thread the antenna onto the

connector until it is secure.

6. Repeat Step 5 with the second antenna, attaching it to the ANT2

port.

7. Position antennas in a “V” shape at a 90 degree angle to each

other.

8. Restore power to the base unit.

3G CDMA NIM LED DESCRIPTIONS

LED Label LED Color Indication

WWAN Off 3G modem is not powered.

Green (solid) 3G modem is powered, associated, and

authenticated, but not transmitting or

receiving.

Green (slow flash) 3G modem is powered and searching, but

not associated or authenticated.

Green (intermittent

flash)

3G modem activity proportional to

transmitting/receiving speed (3 Hz

minimum rate, 20 Hz maximum rate).

RSSI

(Received

Signal

Strength

Indication)

Off No service or no signal detected.

Red (solid) Low signal strength.

Amber (solid) Medium signal strength.

Green (solid) High signal strength.

1xRTT Off No 1xRTT service is available.

Green (solid) 1xRTT service is available.

EVDO Off No 1xEV-DO service is available.

Green (solid) 1xEV-DO service is available.

Important: For additional details on product features,

specifications, installation, and safety, refer to the appropriate

hardware installation guide on the AOS Documentation CD

shipped with the base unit and available online at

www.adtran.com.

NetVanta 3G CDMA Network Interface Module (NIM) P/N 1700801G1, 1700802G1

GETTING ACELLULAR ACCOUNT

Before you attempt to connect the 3G CDMA network interface module

(NIM) to the cellular network, make sure you have subscribed to an

appropriate CDMA service plan with your wireless service provider. The

electronic serial number (ESN) might be needed for this process. The ESN

can be obtained from the label on the 3G modem or by using the show

interface cellular hardware command at the command line interface (CLI)

prompt. Refer to the NetVanta base unit quick start guide for instructions on

accessing the AOS CLI.

GETTING STARTED

Once you have subscribed to a CDMA service plan, you must activate the

3G CDMA NIM. Two activation and configuration methods are available for

your NetVanta 3G CDMA NIM:

• Web-based graphical user interface (GUI)

•CLI

The GUI lets you configure the unit’s settings and provides online guidance

and explanations for each setting. However, using the AOS CLI may be

necessary for more advanced configurations.

ACCESS THE GUI

You can access the GUI from any Web browser on your network by

following these steps:

1. Connect the base unit to your PC using the Ethernet ports on the front

of the unit.

2. Set your PC to a fixed IP address of 10.10.10.2. If you cannot change

the PC’s IP address, you will need to change the unit’s IP address

using the CLI.

3. Enter the unit’s IP address in your browser address line. The default IP

address is 10.10.10.1.

4. You will then be prompted for the user name and password (the default

settings are admin and password).

5. The initial GUI screen appears.

ACTIVATING THE 3G CDMA NIM VIA THE GUI

To activate the 3G CDMA NIM and cellular interface, follow these steps:

1. Select Physical Interfaces from the System menu.

2. Select the Cellular interface to modify from the menu.

3. Select Activate in the Maintenance dialogue box.

4. After activation, enter a Description of the Cellular interface (optional),

check the Enable box, and select Apply.

5. After enabling the Cellular interface, the demand routing interface must

be configured before the 3G CDMA NIM can access the network.

For complete configuration information of the 3G NIM,

cellular interface, and demand routing interface for network

access, refer to the 3G CDMA NIM/Cellular Interface

Configuration Guide available at www.adtran.com.

Refer to the quick start guide shipped with your NetVanta base

unit for instructions on accessing the CLI, configuring the base

unit’s IP address, and enabling Telnet access.

Este manual sirve para los siguientes modelos

Otros manuales de Hardware de red de ADTRAN

ADTRAN

ADTRAN HDSL 3192 HTU-C Manual de instrucciones

ADTRAN

ADTRAN DS3 NIU3 Manual de instrucciones

ADTRAN

ADTRAN T200 SHDSL Manual de usuario

ADTRAN

ADTRAN Smart 16e Shelf Manual de usuario

ADTRAN

ADTRAN 3.125 Gigabit Ethernet Manual de usuario

ADTRAN

ADTRAN Total Access 300 Series Manual del producto

ADTRAN

ADTRAN NetVanta 8044M Manual de usuario

ADTRAN

ADTRAN 1442702PG1 Manual de usuario

ADTRAN

ADTRAN Express 3100 Manual de usuario

ADTRAN

ADTRAN 401 1 GE Micro ONT Manual de usuario

ADTRAN

ADTRAN Total Access 300 Series Manual de usuario

ADTRAN

ADTRAN NetVanta 8044M Manual de usuario

ADTRAN

ADTRAN Total Access 300 Series Manual del producto

ADTRAN

ADTRAN 622v XGS-PON ONT Manual de usuario

ADTRAN

ADTRAN DS3 MX Manual de usuario

ADTRAN

ADTRAN Total Access 5006 Manual de usuario

ADTRAN

ADTRAN P/N 1204011L1 Manual de servicio

ADTRAN

ADTRAN NIU3 Manual de instrucciones

ADTRAN

ADTRAN 850-VoDSL Manual de usuario

ADTRAN

ADTRAN Bluesocket 1700900F1 Manual de usuario

ADTRAN

ADTRAN Express 6530 6530 Manual

ADTRAN

ADTRAN NetVanta Series Manual de usuario

ADTRAN

ADTRAN NetVanta Analog Modem Dial Backup Interface... Manual de usuario

ADTRAN

ADTRAN HDSL4 Manual de instrucciones

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario