ADT OC845 Manual de usuario
ADT Interactive Solutions: Control & Pulse
OC845 Wireless FHD Outdoor Camera
Quick Installation Guide
ADT OC845 FHD Outdoor Camera
Quick Installation Guide
OC845 Outdoor FHD Camera Installation Guide
2
Table of Contents
1Introduction.................................................................................3
1.1 Feature Overview ................................................................3
1.2 Physical Details: Front and Rear Panels ...........................4
1.3 Packaging Contents............................................................5
2Basic Setup .................................................................................5
2.1 Assembling the Camera .....................................................5
2.2 Power-Up .............................................................................5
2.3 Final Steps ..........................................................................6
3ADT Control Enrollment ..............................................................6
3.1 Using Soft AP to Enroll Camera..........................................6
4ADT Pulse Enrollment .................................................................9
4.1 Using WPS PIN to Enroll Camera .......................................9
5Wall Mounting .......................................................................... 14
5.1 Smart IR and Mounting Suggestion................................ 16
6Troubleshooting ....................................................................... 17
6.1 If the Camera Continually Goes Offline .......................... 17
7Appendix................................................................................... 18
7.1 Technical Specifications.................................................. 18
7.2 Regulatory Approvals....................................................... 19
7.2.1 Federal Communication Commission Interference
Statement....................................................................... 19
7.2.2 Industry Canada Statement................................. 20
©2019 ADT LLC dba ADT Security Services. All rights reserved. ADT, the ADT logo,
1.800.ADT.ASAP and the product/service names listed in this document are marks and/or
registered marks. Unauthorized use is strictly prohibited. OC845 (10/19)
Property of ADT, LLC. Information accurate as of published date and is provided “as is”
without warranty of any kind.
ADT OC845 FHD Outdoor Camera
Quick Installation Guide
OC845 Outdoor FHD Camera Installation Guide
3
1Introduction
This section provides information about the OC845 Outdoor Day/Night FHD
Camera's features, components and capabilities.
1.1 Feature Overview
The OC845 is an Outdoor day/night camera with FHD resolution and 802.11ac
Wi-Fi connectivity intended for use with both ADT Control® and Pulse®.
•Standalone Design. The camera is a standalone system with built-in CPU
and video encoder. It requires only a power source and a connection to the
network (Customer router for Control or ADT Pulse gateway).
•Dual Video Support. The OC845 supports H.264 and MJEPG video
compression.
•Day/Night Switch. With the day/night switching feature, you can view and
record images even at night.
•IR LED Support. The two infrared LEDs can provide illumination for up to 5
meters/16 feet, providing superior video quality under low-light conditions.
•PIR (Passive Infrared Sensor) Support. The embedded PIR Sensor senses
infrared light radiating from human bodies in its field of view.
•Built-in Heater. The built-in heater ensures that the camera will continue to
operate even in extremely cold outdoor climates. The heater turns on when
the temperature falls below 42°F (6°C).
•802.11ac Support. The 802.11ac standard provides backward
compatibility with the 802.11b, g and n standards.
•Supports both Soft AP and WPS. Soft AP connectivity is used on the Control
platform. Wi-Fi Protected Setup (WPS) uses a push button to connect to the
Pulse platform.
•Wireless Network. The OC845 is connected to the network wirelessly.
•Two-Way Audio. The OC845 has a speaker and microphone for two-way
conversations and echo cancellation.
ADT OC845 FHD Outdoor Camera
Quick Installation Guide
OC845 Outdoor FHD Camera Installation Guide
4
1.2 Physical Details: Front and Rear Panels
Component
Description
DC Power Jack
Connect the supplied 12V power adapter. Do not use
other power adapters; doing so may damage the camera.
Tri-Color LED Indicator for
Power/Network/WPS
Off: Unit does not have power
On: (Blue) Unit is booting up then LED will blink blue ten
times
Blinking: (Green/Amber) The power LED will blink
green/amber after initial startup is completed. This
indicates that the Soft AP OR WPS PIN mode is ready.
On: (Green) Camera is connected to Network.
Blinking: (Green) Camera has lost connection to the
Network
Blinking: (Amber) Unit is in WPS PIN mode and/or the
WPS connection is in progress.
On: (Amber) If the LED is on for 5 seconds and then turns
off, the WPS function has failed.
WPS/Reset Button
This button serves two functions on the camera.
WPS PIN Mode: When pressed and held for 5 seconds
during the Pulse enrollment process, the camera creates
an encrypted secure wireless connection.
Reset: When pressed and held for 15 seconds, the
camera reboots and settings are restored to default
values.
Lens
The lens is fixed and cannot be adjusted. Please ensure
that the lens cover remains clean of dust and debris.
IR LED
Built-in Infrared LEDs for Night Time Illumination
Light Sensor
This is a hardware sensor to detect daylight level or lux.
ADT OC845 FHD Outdoor Camera
Quick Installation Guide
OC845 Outdoor FHD Camera Installation Guide
5
PIR Sensor
This is a Passive Infrared Sensor to detect motion
Microphone
Built-in Microphone with echo cancelation
Speaker
Built-in Speaker (1W)
Micro SD Card Slot
Built-in Micro SD Card Slot for future enhancements
Note: As the microSD card slot is not currently functional, please do not
remove this protective cover.
1.3 Packaging Contents
2Basic Setup
This section provides information on how to assemble and configure the
OC845 Outdoor FHD Camera for enrollment.
2.1 Assembling the Camera
•Temporarily locate the camera close to the computer for enrollment.
•Attach the camera stand to the camera and connect the power cable.
•Screw/attach the camera onto the camera stand.
2.2 Power-Up
•Connect the 12V power adapter to the camera and power up near the
location where you will be performing the enrollment.
ADT OC845 FHD Outdoor Camera
Quick Installation Guide
OC845 Outdoor FHD Camera Installation Guide
6
Caution: Use the power adapter provided. Using a different
power adapter may result in hardware damage.
2.3 Final Steps
•Check LED Status
-The LED lights up solid blue then blinks ten times during startup,
which takes about 30 seconds. After startup is completed, and
prior to enrollment, the power LED blinks green/amber.
•Enroll the Camera
-The process for enrolling the camera on Control is described in
Section 3: ADT Control Enrollment.
-The process for enrolling the camera on Pulse is described in
Section 4: ADT Pulse Enrollment.
•Mounting the Camera
-Mount the camera in its final permanent location. For mounting on
a wall using the mounting bracket, see Section 5: Wall Mounting.
3ADT Control Enrollment
This section provides instructions for wirelessly enrolling the OC845 Outdoor
FHD Camera onto the ADT Control platform. This process uses the Soft AP
method to wirelessly connect the FHD Camera to the Customer’s network.
3.1 Using Soft AP to Enroll Camera
•Set up the camera as described in the previous section.
-Connect the camera’s AC power adapter and plug it into a power
outlet.
-Wait for the power LED to blink green/amber.
ADT OC845 FHD Outdoor Camera
Quick Installation Guide
OC845 Outdoor FHD Camera Installation Guide
7
•Connect to the camera’s network SSID using a laptop or mobile device. The
SSID is the model number of the camera and part of the MAC address. For
example, SSID = OC845 (XX:XX:XX).
•Open a web browser (IE, Chrome, Firefox, etc.). Type in adt1.com and you
will be directed to the install wizard page.
•Choose a language.
•Click Scan for Wi-Fi Networks and select the Customer’s router SSID.
Note: Control cameras will connect to the
Customer’s Wi-Fi network to access the
Internet to be added to the Control
platform. It is imperative that the customer
understands that all camera locations are
limited by their existing Wi-Fi network and
its range. Additionally, the Customer will
need to enter their SSID password during
the subsequent step.
ADT OC845 FHD Outdoor Camera
Quick Installation Guide
OC845 Outdoor FHD Camera Installation Guide
8
•Enter the wireless credentials and click Save.
•The LED will turn solid green when data is being transmitted indicating that
the connection to the Customer’s router is complete.
•Connect a laptop or mobile device to the Customer’s network and log in to
the Control web portal, https://www.adt.com/control-login, to complete the
setup.
•Select Video from the menu list.
•Click Settings and select Add Video Device.
•Select install from the video device list to begin adding camera. If a laptop
or mobile device are not on the Customer’s network, then enter the MAC
address of the camera.
•Follow the on-screen instructions to finish adding the camera.
ADT OC845 FHD Outdoor Camera
Quick Installation Guide
OC845 Outdoor FHD Camera Installation Guide
9
4ADT Pulse Enrollment
This section provides instructions for wirelessly enrolling the OC845 Outdoor
FHD Camera into the ADT Pulse network. This process uses the Wi-Fi
Protected Setup (WPS) with PIN method to wirelessly enroll the FHD Camera
to the gateway via the ADT Pulse Portal or TS Installer App.
4.1 Using WPS PIN to Enroll Camera
•Set up the camera as described in Section 2.
•Launch an Internet browser and log in to the Pulse portal or TS Installer app.
•Enter the Manage Devices screen using one of these methods:
-For Pulse portal, select the System Tab and click Manage Devices.
-For TS Installer app, click the Pulse Devices link. The Manage
Devices screen will display.
•In the Manage Devices screen, click Cameras.
•Click the Add Using WPS button located at the bottom of the screen.
ADT OC845 FHD Outdoor Camera
Quick Installation Guide
OC845 Outdoor FHD Camera Installation Guide
10
•Locate the camera’s PIN number on the product label on the rear of the
camera.
•Enter the camera’s PIN into the WPS PIN field.
•Ensure that the camera is powered on and that the LED is flashing
green/amber.
Tabla de contenidos
Otros manuales de Cámara digital de ADT
