ADT Pulse OC810-ADT Manual de usuario
ADT Pulse®Interactive Solutions
OC810-ADT Wireless
Outdoor Day/Night Camera
Installation Guide
OC810-ADT Wireless Outdoor Day/Night Camera Installation Guide
Table of Contents
INTRODUCTION ........................................................................................................... 1
Overview .......................................................................................................................1
OC810-ADT Camera Features..........................................................................1
Package Contents .......................................................................................................2
Physical Details – OC810-ADT Camera .................................................................3
Front Panel ............................................................................................................3
Rear Panel..............................................................................................................4
INSTALLATION ............................................................................................................. 5
Adding the OC810-ADT Wireless Outdoor Day/Night Camera to the ADT
Security System...........................................................................................................5
PIR Video Motion Detection......................................................................................9
Enabling Motion Detection via the ADT Security System ....................... 11
APPENDIX A: SPECIFICATIONS ............................................................................ 13
APPENDIX B: REGULATORY APPROVALS.......................................................... 14
FCC Statement.......................................................................................................... 14
CE Approvals .............................................................................................................14
UNITED STATES LICENSE INFORMATION: AL Alabama Electronic Security Board of Licensure,
7956 Vaughn Rd., Montgomery 36116, (334) 264-9388; AK 37950, 5520 Lake Otis Pkwy.,
Anchorage, AK 99507; AR E12-041, Regulated by Arkansas Bd. of Private Investigators & Private
Security Agencies, #1 State Police Plaza Dr., Little Rock, AR 72209, (501) 618-8600; AZ ROC
279591; CA ACO7155, alarm company operators are licensed and regulated by the Bureau of
Security & Investigative Services, Dept. of Consumer Affairs, Sacramento, CA 95814, 974443,
PPO17232; CT ELC.0106069-L5; DC ECS902743; FL EF0001121; GA LVA205265, -205326, -
205572, -205679, -205878, LVU405673, -004349; HI CT-32297; ID ELE-SC-2643;
IL 124001792; LA F1639, F1640, F1643, F1654, F1655; MA 172C; MI 3601206258,
5103208 - 4182 Pier North Dr. Ste. D, Flint, MI 48504; MN TS650251; NC 7535P2, 7561P2,
7562P10, 7563P7, 7565P1, 7566P9 - Alarm Systems Licensing Bd., 4901 Glenwood Ave, Ste.
200, Raleigh, 27612 (919) 788-5320; NM 374838; NV 0077105; NJ Electrical Contractor Lic. #'s
34FA00140500, 34BA00179000, 7895 Browning Rd., Pennsauken, NJ 08109;
NY 12000305615, Licensed by NYS Dept. of State; OH 50-18-0018, 50-25-0023, 50-29-0003, 50-
31-0014, 50-48-0008, 50-50-0005, 50-76-0006, 50-89-0016, 53-89-1726; OK 1995;
OR 196560; PA Pennsylvania Home Improvement Contractor Registration Number: PA090797;
RI 35683; TN ACC-1688, -1689, -1690, -1691, -1692, -1693, -1694, -1695, -1696; TX B17944 -
140 Heimer Rd. Ste. 100, San Antonio, TX 78232 - Texas Private Security Bureau, 5805 N. Lamar
Blvd., Austin 78752; UT 8289653; VA 11-7345, 11-7348, 11-7351, 11-7354, 11-7598, 11-7900,
11-8205, 11-8353, 11-8447 2705147728 Class B Contractor Classification ESC;
WA ADTLLL881DO, 11824 N Creek Pkwy #105, Bothell, WA 98011; WI 1210943; WV 049758.
MS 15019511
©2013 ADT LLC dba ADT Security Services. All rights reserved. ADT, the ADT logo, 800 ADT.ASAP
and the product/service names listed in this document are marks and/or registered marks.
Unauthorized use is strictly prohibited.
Canada Licence number: RBQ 3019-4070-50. ©2013 ADT Security Services Canada, Inc. All rights
reserved. ADT, the ADT logo, 800.ADT.ASAP and the product/service names listed in this document
are marks and/or registered marks. Unauthorized use is strictly prohibited.
Document 957YU606MY
Version 2.3
ii ADT Pulse®Interactive Solutions
OC810-ADT Wireless Outdoor Day/Night Camera Installation Guide
Introduction
This section provides details of the OC810-ADT Wireless Outdoor Day/Night
Camera features, components and capabilities.
Overview
The OC810-ADT Wireless Outdoor Day/Night Camera (hereafter referred to as
the wireless camera) has an Integrated Microcomputer and a high quality digital
Image Sensor, enabling it to display high quality, live streaming video to your
web or mobile client over an 802.11n Wireless LAN.
OC810-ADT Camera Features
•Standalone Design: The wireless camera is a standalone device which
requires a power source and a wireless connection to the ADT Pulse®
gateway.
•Triple Video Support: The wireless camera can support H.264, MEPG4
and MJEPG video for different image compression.
•Day/Night Switch: With the automatic day/night switching feature, the
wireless camera is able to view and record crisper images in the dark within
a 25 foot area.
•Standard Compliance: The wireless camera complies with the
IEEE802.11n (DSSS) specifications for Wireless LANs.
•Supports 802.11n Wireless Stations: The 802.11n Draft standard
provides for backward compatibility with the 802.11g wireless network.
•Speeds up to 108Mbps: All speeds up to the 802.11n maximum of
108Mbps are supported.
•Security Support: Full WEP (64/128 Bit), WPA and WPA2 Personal
standards are supported on the Wireless interface allowing advanced
encryption of wireless data.
ADT Pulse®Interactive Solutions 1
OC810-ADT Wireless Outdoor Day/Night Camera Installation Guide
Package Contents
1. OC810-ADT Wireless Outdoor Day/Night Camera
2. Antenna
3. Power Adapter
4. Ethernet Cable
5. Power Extension Cable(with water sealing cap)
6. Stand
7. Mounting Screws
8. Quick Installation Guide
2 ADT Pulse®Interactive Solutions
OC810-ADT Wireless Outdoor Day/Night Camera Installation Guide
Physical Details – OC810-ADT Camera
Front Panel
Figure 1: Front Panel
1. Lens
No physical adjustment is required or possible for the
lens, but you should ensure that the lens cover remains
clean. Image quality is degraded if the lens cover is dirty
or smudged.
2. Power LED
On - Power on.
Off - Power off.
Blinking - The Power LED blinks during power up. (This
can take up to 20 seconds).
3. Light Sensor
The Light Sensor detects luminance.
4. IR LEDs
The LEDs enable the wireless camera to see images at
night or in a dark environment.
ADT Pulse®Interactive Solutions 3
OC810-ADT Wireless Outdoor Day/Night Camera Installation Guide
Rear Panel
Figure 2: Rear Panel
1. Antenna
The antenna is adjustable with best results typically
obtained with the antenna positioned vertically.
2. Power Port
The supplied 12V power adapter plugs power to the
wireless camera’s power port.
IMPORTANT
DO NOT USE ANY POWER ADAPTER OTHER THAN
THE ONE SPECIFIED FOR THIS CAMERA. DOING SO
MAY DAMAGE THE WIRELESS CAMERA.
3. Ethernet Port The Ethernet port enables connectivity of the wireless
camera to your ADT Pulse gateway.
IMPORTANT
•PLUGGING IN THE ETHERNET CABLE WILL
DISABLE THE WIRELESS INTERFACE. (ONLY ONE
INTERFACE CAN BE ACTIVE AT ANY TIME.)
•THE ETHERNET CABLE SHOULD ONLY BE
CONNECTED OR DISCONNECTED WHEN THE
OUTDOOR DIGITAL CAMERA IS POWERED OFF.
ATTACHING OR DETACHING THE ETHERNET
CABLE WHILE THE CAMERA IS POWERED ON
DOES NOT SWITCH THE INTERFACE BETWEEN
WIRED AND WIRELESS.
•DETACHING THE ETHERNET CABLE WHEN THE
OUTDOOR DIGITAL CAMERA IS POWERED ON
WILL DISCONNECT THE OUTDOOR DIGITAL
CAMERA FROM THE NETWORK.
4. Reset Button When pressed and held for ten (10) seconds, the
communication configuration of the wireless camera will
be reset to the default manufacturer settings.
IMPORTANT
THE RESET BUTTON WILL RESET THE CAMERA
COMMUNICATION CONFIGURATION SETTINGS AND
SHOULD ONLY BE USED UNDER THE DIRECTION OF
ADT SUPPORT.
4 ADT Pulse®Interactive Solutions
OC810-ADT Wireless Outdoor Day/Night Camera Installation Guide
Installation
This section provides details of installing and configuring the OC810-ADT
Wireless Outdoor Day/Night Camera.
Adding the OC810-ADT Wireless Outdoor Day/Night
Camera to the ADT Security System
NOTE:
The OC810-ADT wireless camera can only be added to a Pulse
system that supports video.
1. Open your web browser. In the address bar, type:
https://Portal.ADTPulse.com.
2. Type your Username and Password, and then click the Sign In button.
3. Click the System tab, and then click the Manage Devices button.
ADT Pulse®Interactive Solutions 5
OC810-ADT Wireless Outdoor Day/Night Camera Installation Guide
4. In the Manage Devices Assistant, click Cameras.
5. Click the picture of the OC810 or select it from the drop-down list, and then
click the Continue button.
6. Assign the wireless camera a unique name (this is usually based on the
location of the wireless camera) in the space provided, and then type the
wireless camera’s MAC ID or Server Name.
6 ADT Pulse®Interactive Solutions
OC810-ADT Wireless Outdoor Day/Night Camera Installation Guide
7. Click the Continue button.
8. Attach the antenna to the wireless camera. To adjust the antenna, screw to
the rear mounting point and set the antenna to the upright position to
improve wireless reception.
9. Connect the wireless camera to the Device Port of the gateway using a
standard LAN cable.
10. Connect the supplied 12V power adapter to power up the wireless camera,
and then click the Continue button.
NOTE
The Power LED turns on briefly, and then starts blinking during
startup, which takes approximately 5 to 20 seconds. After
startup is completed, the Power LED remains ON.
ADT Pulse®Interactive Solutions 7
OC810-ADT Wireless Outdoor Day/Night Camera Installation Guide
11. Once connected, click the Continue button.
12. Click the Finish button. The installation is complete.
13. Disconnect the wireless camera from the gateway and remove from power.
14. Assemble the mounting bracket, and then install the wireless camera in the
final location.
15. Re-apply power.
If the camera does not connect, use of the ADT Wi-Fi extender, part #
WN2RPADT-1ADNAS is recommended and may improve connectivity.
For more information, refer to Physical Details – on pages 3 and 4.
8 ADT Pulse®Interactive Solutions
Tabla de contenidos
Otros manuales de Cámara de seguridad de ADT Pulse
