ADJ Dotz Panel 2.4 Manual de usuario

User Manual

DOTZ PANEL 2.4

Rev. 12/2020

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be trade-

marks or registered trademarks of their respective companies and are hereby acknowledged. All

non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 2

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 3

Unpacking: Thank you for purchasing the Dotz Panel 2.4 by ADJ Products, LLC. Every Dotz Panel 2.4

has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the

shipping carton for damage that may have occurred during shipping. If the carton appears to be dam-

aged, carefully inspect your xture for any damage and be sure all accessories necessary to operate

the unit has arrived intact. In the case damage has been found or parts are missing, please contact our

toll free customer support number for further instructions. Do not return this unit to your dealer without

rst contacting customer support.

Introduction: The Dotz Panel 2.4 is part of ADJ’s continuing pursuit for creating high quality aord-

able intelligent xtures. The Dotz Panel 2.4 is a high performance, DMX intelligent, LED xture. This

xture is a great piece for retail stores, displays, mood, architectural, interior and exterior decoration,

and clubs. This unit can be used as a stand alone unit, or in a Primary/Secondary conguration. The

unit can also be controlled via DMX controller. This xture is suitable for theaters, studios, retail stores,

and other similar locations.

Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide set up

help and to answer any questions should you encounter problems during your set up or initial opera-

tion. You may also visit us on the web at www.adj.com for any comments or suggestions. Service

Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.

Voice: (323) 582-2650

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit parts.adj.com.

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufactures war-ranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

Dotz Panel 2.4 Introduction

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 4

Dotz Panel 2.4 General Instructions

To optimize the performance of this product, please read these operating instructions carefully to

familiarize yourself with the basic operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please keep this manual with the unit for

future reference.

• RGB Color Mixing

• Strobing

• Electronic Dimming 0-100%

• Built in Microphone

• DMX-512 protocol

• Five DMX Modes: 3 Channel Mode, 6 Channel Mode, 8 Channel Mode, 24 Channel Mode, & 29

Channel Mode

• 4 Operating Modes - Sound Active, Auto Run, Built-In Programs, or DMX Control

• Power Cord Daisy Chain Capability (see Power Cord Daisy Chaining section of this manual)

The Dotz Panel 2.4 carries a 2 year (730 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase and warranty. You may also regis-

ter your product online at www.adj.com.

All returned service items, whether under warranty or not, must be freight pre-paid and accompanied

by a return authorization (R.A.) number. If the unit is under warranty you must provide a copy of your

proof of purchase invoice. Please contact ADJ Products, LLC customer support for an R.A. number.

Dotz Panel 2.4 Warranty Registration

Dotz Panel 2.4 Features

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 5

Dotz Panel 2.4 Safety Precautions

• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt- age for your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt

to remove or break off the ground prong from the electrical cord. This prong is used to reduce the

risk of electrical shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out` doors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by t he manufacturer. See page 21

for cleaning details.

• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

1. The power-supply cord or the plug has been damaged.

2. Objects have fallen, or liquid has been spilled into the appliance.

3. The appliance has been exposed to rain or water.

4. The appliance does not appear to operate normally or exhibits a marked change in perfor-

mance.

Dotz Panel 2.4 Set Up

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 6

Power Supply: The ADJ Dotz Panel 2.4 contains an automatic voltage switch, which will auto sense

the voltage when it is plugged into the power source. With this switch there is no need to worry

about the correct power voltage, this unit can be plugged in anywhere. Always use the power cable

that was included with the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and

controller manufacturers as a form of communication between intelligent xtures and controllers. A

DMX controller sends DMX data instructions from the controller to the xture. DMX data is sent as

serial data that travels from xture to xture via the DATA “IN” and DATA “OUT” XLR terminals locat-

ed on all DMX xtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be

linked together and operate from a single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using several DMX xtures try to use

the shortest cable path possible. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example; a xture assigned a DMX address of 1 may be placed

anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Dotz Panel 2.4 can be con-

trolled via DMX-512 protocol. The Dotz Panel 2.4 has 5 DMX Channel Modes. The DMX address is

set on the rear panel of the Dotz Panel 2.4. Your unit and your DMX controller require an approved

DMX-512 110 Ohm Data cable for data input and data output (Figure 1). We recommend Accu-Cable

DMX cables. If you are making your own cables, be sure to use standard 110-120 Ohm shielded ca-

ble (This cable may be purchased at almost all professional sound and lighting stores). Your cables

should be made with a male and female XLR connector on either end of the cable. Also remember

that DMX cable must be daisy chained and cannot be split.

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 7

Dotz Panel 2.4 Set Up

Notice: Be sure to follow gures two and three when making your own cables. Do not use the

ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug

or allow the shield conductor to come in contact with the XLR cable’s outer casing. Grounding the

shield could cause a short circuit and erratic behavior.

Special Note: Line Termination. When longer runs of cable are used, you may need to use a termi-

nator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which

is connected between pins 2 and 3 of a male XLR connector (DATA+ and DATA-). This unit is inserted

in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable

terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.

5-Pin XLR DMX Connectors. This unit use 5-pin DMX-512 data cables for DATA transmission. 5-pin

DMX xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in

to a 3-pin line, a cable adaptor must be used. These adaptors are readily available at most electron-

ics stores. The chart below details a proper cable conversion.

Dotz Panel 2.4 System Menu

BUILT IN PROGRAMS

STATIC COLOR

CL:RGB, Flash 00-99

Blackout, Red-Green-Blue-Yellow-Cyan-Purple-White

Flash speed adjustable

DREAM

Speed 00-99, Flash 00-99

Seven color dreaming

Speed and Flash adjustable

METEOR

Speed 00-99, Flash 00-99

Seven color flow

Speed and Flash adjustable

FADE

Speed 00-99, Flash 00-99

Seven color fade

Speed and Flash adjustable

CHANGE

Speed 00-99, Flash 00-99

Seven color change

Speed and Flash adjustable

FLOW 1

Speed 00-99, Flash 00-99

Seven color chase

Speed and Flash adjustable

FLOW 2

Speed 00-99, Flash 00-99

Seven color chase

Speed and Flash adjustable

FLOW 3

Speed 00-99, Flash 00-99

Seven color chase

Speed and Flash adjustable

FLOW 4

Speed 00-99, Flash 00-99

Seven color chase

Speed and Flash adjustable

FLOW 5

Speed 00-99, Flash 00-99

Seven color chase

Speed and Flash adjustable

FLOW 6

Speed 00-99, Flash 00-99

Seven color chase

Speed and Flash adjustable

FLOW 7

Speed 00-99, Flash 00-99

Seven color chase

Speed and Flash adjustable

FLOW 8

Speed 00-99, Flash 00-99

Seven color chase

Speed and Flash adjustable

FLOW 9

Speed 00-99, Flash 00-99

Seven color chase

Speed and Flash adjustable

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 8

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 9

Dotz Panel 2.4 System Menu

The LCD backlight will shut o after 30 seconds. To reactive the backlighting, press and hold

the MODE button for 5 seconds.

DMX Mode - Set the DMX Address and DMX Channel Mode.

1. Press the MENU button until “DMX Mode” and underneath “ADDR: XXX” and “CH:XX” is dis-

played, press ENTER.

2. “XXX” will now begin to ash, use the UP and DOWN buttons to nd your desired DMX address,

then press ENTER.

3. “XX” will now begin to ash, use the UP and DOWN buttons to nd your desired DMX Channel

mode, then press ENTER.

Secondary Mode - This will let you set your unit as a secondary unit in a primary/secondary

conguration.

1. Press the MENU button until “Secondry Mode” is displayed.

2. Your unit will now follow the behavior of the Primary unit.

Sound Mode - In this mode the unit will run in sound active mode.

1. Press the MENU button until “Sound Mode” is displayed.

2. Press ENTER to adjust your sound sensitivity. When you press ENTER the number next to “Sens”

will begin to ash, use the UP and DOWN buttons to adjust the sound sensitivity. Once you found

your desired sensitivity press ENTER to conrm.

3. When you press ENTER the number next to “FQN” will begin to ash, use the UP and DOWN

buttons to adjust the amount of times you would like the program to cycle before changing to the

next program. Press ENTER to conrm.

Auto Run.

1. Press the MENU button until “Auto Run” is displayed, and “FQN:XX” will be displayed under-

neath. “XX” representing the number displayed.

2. Press ENTER and the number will begin to ash, use the UP and DOWN buttons to adjust the

amount of times you would like the program to cycle before changing to the next program. Press

ENTER to conrm.

Built-In Programs - See the chart for Built-In Programs at the beginning of this section for de-

tailed descriptions of the available programs.

1. Press the MENU button until one of the Programs shown in the Built-In Program table is dis-

played. The displayed program depends on the last program you had set the unit to.

2. Press ENTER to move through the various adjustments of each program, and use the UP and

DOWN button to make adjustments.

Dim Curve - This setting will let you select your desired dimming curve.

1. Press the MENU button until “Dim Curve” is displayed, press ENTER.

2. 1 of 5 dimming curve settings will be displayed: Standard, Stage, TV, Architectural, or Theatre.

Use the UP and DOWN buttons to select your desired dimming curve and press ENTER to con-

rm.

ADJ Products, LLC - www.adj.com - Dotz Panel 2.4 User Manual Page 10

Dotz Panel 2.4 System Menu

Pixel Flip - In this mode you adjust the unit so that the LEDs in DMX mode will illuminate at

your desired starting point.

1. Press the MENU button until “Pixel Flip” is displayed, press ENTER.

2. Either “OFF” or “ON”, will be displayed. “ON” will have the unit light up bottom right to left. “OFF”

will have the unit light up top left to right. Use the UP or DOWN buttons to nd your desired set-

ting, and press ENTER.

NO DMX - This mode is used to dene how the xture will behave in the event that DMX signal

is lost or interrupted.

1. Press the MENU button until “NO DMX” is displayed, and either “Sound”, “Auto”, “Black”, or

“Hold” will be displayed beneath.

2. Press ENTER and the bottom choice will begin to ash. Use the UP or DOWN buttons to choose

an operating mode you would like the unit to start up in when power is applied or the DMX signal

is lost.

• Sound - If the DMX signal is lost or power is applied, the unit will automatically go into

sound active mode.

• Auto - If the DMX signal is lost or power is applied, the unit will automatically go into Auto

Run Mode.

• Black (Blackout) - If the DMX signal is lost or power is applied, the unit will automatically go

into stand by mode.

• Hold - If the DMX signal is lost the xture will stay in the last DMX setting. If power is applied

and this mode is set, the unit will automatically go into the last DMX set up.

3. Press ENTER to conrm your desired set up.

Personality - This will let you set your unit as a Primary in a primary/secondary conguration.

1. Press the MENU button until “Personality” is displayed. Your unit will now be the Primary unit in a

Primary-Secondary conguration.

Otros manuales para Dotz Panel 2.4

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Luminaria de ADJ

Manuales populares de Luminaria de otras marcas

Emos

Emos CLASSIC ZY1431T Manual de usuario

Westinghouse

Westinghouse Outdoor Lighting Fixture Manual de usuario

Hedler

Hedler C 12 silent Manual de usuario

Blizzard Lighting

Blizzard Lighting Puck: CSI Manual de usuario

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manual de usuario

Lightmaxx

Lightmaxx Shaft 5R Manual de usuario

Triarch

Triarch 31083 Manual de usuario

Philips

Philips 32614 Series Manual de usuario

IKEA

IKEA TIVED Manual de usuario

Lightolier

Lightolier LP200 Manual de usuario

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manual de usuario

Martin

Martin MAC 250 Krypton Manual de usuario

Cooper Lighting

Cooper Lighting Halo L3232E Manual de usuario

Stageline

Stageline ODW-2410RGBW Manual de usuario

Light Sky

Light Sky Tornado Series Manual de usuario

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manual de usuario

Lightolier

Lightolier Lytespan 83ED17S Manual de usuario

Lightolier

Lightolier Calculite CS8226 Manual de usuario