Adeunis RF TWIMO Series Manual de usuario

208474A_UG_Starter kit_TWIMO_V1.0

Adeunis RF

TWIMO RF Modules

Starter Kit

User Guide

208474A_UG_Starter kit_TWIMO_V1.0

Table of contents

Preliminary information 4

Precautions 4

1. Product overview 5

2. Kit content 5

3. Getting around the TWIMO Starter Kit 5

3.1. Extension board overview

3.2. Open4 platform overview 6

4. Before starting 7

4.1. Connect the extension board to the Open4 platform 7

4.2. Turn on the system 7

5. Running the evaluation 8

5.1. Start-up screen 8

5.2. Home screen 9

5.3. Select the type of module 9

 5.4. Modifytheconguration 9

5.4.1 RF Power 9

5.4.2 RF data rate 10

5.4.3 Channel (frequency) 10

6. Test mode 11

6.1. TX/RX mode 11

6.2. «Received level» mode 12

6.3. «Scanner» mode 13

6.4. USB mode 14

6.5. Running screen 14

6.6. General notes 14

7. Verify or Evaluate an installation 15

7.1. Method # 1 15

7.2. Method # 2 15

8. Products references 15

9. DECLARATION OF CONFORMITY (CE0081) 16

208474A_UG_Starter kit_TWIMO_V1.0

English

208474A_UG_Starter kit_TWIMO_V1.0

Preliminary information

Precautions

Likemostevaluationkits,thisproductisdesignedforuseinofceandlaboratoryenvironments.

The following practices will help ensure its proper operation.

This product uses low power CMOS circuits which can be damaged by electrostatic discharge. Partially da-

maged circuits can function erroneously, leading to misleading results.

Observe ESD precautions at all times when handling this product.

Documents

This document and any copy or extract of it, can’t be disclosed without Adeunis-rf’s formal agreement.

This document is subject to change without notice. All trademarks mentioned in this guide are the property of

their respective owners.

ADEUNIS RF

283 rue Louis Néel

38920 Crolles

France

Phone +33 (0)4 76 92 01 62

Fax +33 (0)4 76 08 97 46

Web www.adeunis-rf.com

208474A_UG_Starter kit_TWIMO_V1.0

1. Product overview

This Starter Kit is designed to help the user to achieve his objectives as quickly as possible. The new generation

of Adeunis RF starter kit consists on the addition of an Adeunis extension board (embedding the TWIMO module)

and a Raisonance Open4 platfom.

Evaluate the Adeunis-RF products

TheusercantransferdatafromoneStarterKittoanotherStarterKit.Thisenablestheusertoquicklyndout

howwelltheAdeunis-RFproductsttheintendedapplication.

Perform RF measurements

ThroughtheAdeunisRFapplicationsoftware,runningintotheOpen4platform,theusercanconguretheradio

module with custom parameters that suit the intended application and easily measure sensitivity, output power

and other RF parameters.

• The documentation can be downloaded on the Adeunis website : www.adeunis-rf.com

2. Kit content

In order to perform tests with the TWIMO extension board, you must use at least one Raisonance Open4 plate-

form («received level» and «scanner» modes) or two plateforms with extension boards if you wish to run «TX/RX

mode».

Each Extension board includes :

• 1 x Soldered TWIMO module (ARF7581AA or ARF7580AA).

• 1 x 869 MHz antenna (LINX)

• 1 x User’s guide

Each Open4 platform includes :

• 1xUSBcable

Adeunis RF

TWIMO extension board

Adeunis RF

TWIMO extension board

Raisonance Open4 platform

3. Getting around the TWIMO Starter Kit

The Adeunis RF extension board must be combined to the Raisonance Open4 platform to run the evaluation.

The Open 4 platform embeds the Adeunis RF application software, the user’s interface (LCD screen) and the

battery, all mandatory to implement the TWIMO module.

208474A_UG_Starter kit_TWIMO_V1.0

3.1. Extension board overview

Antenna socket

TWIMO module

Extension board to Open 4

platform connector

External power supply

3.2. Open4 platform overview

LCD touch screen : allows

to navigate into the menu

USB connector : power

supply & PC connection

Joystick : allows to navigate

into the menu

Adeunis RF extension board

Raisonance target board

All needed and usefull information can be found on the Raisonance website (www.raisonance.com). User

manual of the OPEN4 platform can be found here : Open4 manual

208474A_UG_Starter kit_TWIMO_V1.0

4. Before starting

4.1. Connect the extension board to the Open4 platform

The extension board must be connected to the Open4 platform. Procedure :

• Unscrew the bottom case of the Open 4 by removing the four screws.

• Remove the bottom cover.

• Install the extension board as showed below. The module must faces you. Gently push on the extension

(see red arrow) board to insure a proper connection. Be very careful when proceeding. The extension socket

must be held when inserting the extension board as showed with the orange arrow !!

• Re-install the bottom cover and screws.

• Install the antenna on the extension board antenna socket.

4.2. Turn on the system

To turn on the system, you must activate the On/Off switch located above the target board. See picture below.

208474A_UG_Starter kit_TWIMO_V1.0

The Open4 platform must be charged before use. It can be charged on a PC through the USB cable supplied

with the package.

Note concerning the power supply : in the case of evaluating an Adeunis RF module functionning at 500mW,

you may have to use an external power supply to run the maximum module power for more than an hour. The

extension board is equiped with an external power supply socket (Jack 3.5). Please contact us for details and

powersupplyspecications.

• WhenswitchingontheStarterkit,thesystemwillrstaskyoutocalibratethescreen,proceed.

• When the screen calibration has been done, press the «one dot» button to launch the Adeunis RF applica-

tion.

«one dot» button

5. Running the evaluation

The evaluation can be ran on three different modes :

• TX/RX mode

• Received level mode

• Scanner mode

Set-up the Starter Kit

When the Adeunis RF application has been launched, the following screens will assist you in the set-up pro-

cedure.

5.1. Start-up screen

The home screen shows the application software version and the battery level. Press «Go» to access the menu.

Version Battery level

«Go» icon

208474A_UG_Starter kit_TWIMO_V1.0

5.2. Home screen

The following screen allows to :

• select the type of module to be evaluated.

• modifytheconguration.

• run the evaluation.

• switch to USB mode.

5.3. Select the type of module

Press the «change» icon. A list of the available Adeunis RF extension

board appears.

Select the proper board and press the «validate» icon.

Module type & set-up

Set-up the module

Module type selection

Run the evaluation

USB mode

5.4. Modify the conguration

5.4.1 RF Power

Pressthe«Cong»icon.

Choose the RF Power :

• TWIMO MP (17dBm, 14dBm, 10dBm)

• TWIMO HP (27dBm, 23dBm, 20dBm)

Press the «validate» icon

208474A_UG_Starter kit_TWIMO_V1.0

5.4.2 RF data rate

Following the RF Power mode, the RF Data rate must be selected.

Choose the RF Data rate :

• TWIMO MP & HP : 10kbps, 38.4kbps, 57.6kbps

Press the «validate» icon

5.4.3 Channel (frequency)

Following the RF Data rate, the Channel must be selected.

Choose the channel

Press the «validate» icon

Importante note :

According to the RF Power and Data rate previously chosen, the list of avai-

lable channels is adapted to the European regulation and standards. Please

refer to the table below :

Power RF Data Rate Available Channels (frequencies)

27dBm

10kbps

38.4kbps

57.6kbps

869.525MHz

23dBm

10kbps

38.4kbps

57.6kbps

869.525MHz

20dBm

10kbps

38.4kbps

57.6kbps

869.525MHz

17dBm

10kbps

38.4kbps

57.6kbps

869.525MHz

14dBm

10kbps 869.525MHz

38.4kbps

869.525MHz

868.420MHz

868.320MHz

868.220MHz

868.120MHz

57.6kbps 869.525MHz

10dBm

10kbps 869.525MHz

38.4kbps

869.525MHz

868.420MHz

868.320MHz

868.220MHz

868.120MHz

57.6kbps 869.525MHz

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Adeunis RF

Adeunis RF

Adeunis RF Narrow Band NB868-25mW Manual de usuario

Adeunis RF

Adeunis RF SIGFOX Manual de usuario

Adeunis RF

Adeunis RF Narrow Band NB868-500mW Manual de usuario

Adeunis RF

Adeunis RF ARF26 Manual de usuario

Adeunis RF

Adeunis RF SIGFOX Si868-25mW Manual de usuario

Adeunis RF

Adeunis RF ARF54 Manual de usuario

Adeunis RF

Adeunis RF PULSE V4 Manual del producto

Adeunis RF

Adeunis RF ARF8133A Manual de usuario

Adeunis RF

Adeunis RF Wireless-Mbus 25mW Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario