Addonics Technologies RAID TOWER IX RT93DAHX Manual de usuario

T E C H N O L O G I E S

User Guide

RAID Tower IX

(RT93DAHX / RT93DAHXML)

Technical Support

If you need any assistance to get your unit functioning properly, please have your

product information ready and contact Addonics Technical Support at:

Hours: 8:30 am - 6:00 pm PST

Phone: 408-453-6212

Email: http://www.addonics.com/support/query/

v5.1.11

www.addonics.com

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Removing Cover of RAID

Tower IX

Loosen the 5 screws at the back of the

tower using a Philips screwdriver by

turning counter-clockwise. Separate the

metal casing of the tower from the housing

by lifting up the casing.

Installing drives into the

RAID Tower V

Step 1

Use a Philips screwdriver to secure the

3.5” SATA hard drive to the drive tray

Step 2

Slide the tray into the Disk Array drive bay.

Note: It is recommended to fill up the RAID

Tower IX with SATA drives from top to

bottom. This is to help in identifying which

drives connects to which ports for easier

troubleshooting.

Note: The 5 port HPMXA system version

PCB board is mounted inside the RAID

tower and is connected to the multilane

bridge that is mounted at the back of the

RAID tower.

Screws Screws

RT93DAHX RT93DAHXML

eSATA Ports Multilane Port

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Dip Switch Settings

Enable

ERR Buzzer

Function

Auto-

Rebuilding

to Spare

Drive

Port Multiplier Mode

Raid Mode 1 2 3 4 5

Individual Drive

(Factory Default) OFF

OFF

1 and 10

Clone

Large

RAID Setting Button

Dip Switch

SATA Host Port (Port 5)

SATA Port 2

SATA Port 1

SATA Port 0

SATA Port 3

SATA Port 4

Drive activity LED Jumper Block (J1)

Error LED Jumper Block (J3)

Floppy

Power

Connector

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Default factory DIP Switch setting:

SW1 – RAID Setting DIP Switch

BZS – Error buzzer function

EZ – Automatic rebuilding to spare drive (one of the drives on the raid is set as a

spare). If EZ is ENABLED anda drive failure occurs, the spare will

automatically act as a drive replacement and rebuilding will automatically

start.

M2 – RAID mode 2

M1 – RAID mode 1

M0 – RAID mode 0

1. Error buzzer function is ENABLED (BZS) when dip switch is in OFF position

2. Auto-rebuilding to spare drive is DISABLED (EZ)

3. Individual drive mode is ENABLED (M0~M2)

Note: When the default factory RAID setting is used, independent drive configuration

and optical drive are supported only when connecting to controllers with Silicon

Image Sil3124, Sil3132 chip set or controllers that are Port Multiplier (PM)

compatible. Simultaneous DVD writing was tested using the Nero Burning Rom.

LED Pin Header

J1 – Drive Activity LED

P5 – Activity LED for eSATA host port lights up when it is connected to a

SATA controller card.

P0, P1, P2, P3 & P4 - Activity LEDs for port 0, 1, 2, 3, 4 & 5 light up when a drive is

connected and blinks when there’s drive activity.

J3 – Error LED

P5 – error LED for eSATA host port

P0, P1, P2, P3 & P4 - error LED for port 0, 1, 2, 3, 4 & 5

J3 J1

Error LED Activity LED

P5 P0 P1 P2 P3 P4 P5 P0 P1 P2 P3 P4

1 2 3 4 5

SW1

BZS EZ M2 M1 M0

OFF

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Setting or Modifying the RAID Mode Using the JMicron

HW RAID Manager Utility Program:

1. For Windows users, install the JMicron HW RAID Manager located on the

SATA Controller CD. In the CD, go to Configuration Utilities > JMB393. This

manager can be use to create and monitor the status of the RAID volume.

It is recommended to use the default factory RAID DIP switch setting when

using the JMicron HW RAID Manager.

2. Modify the RAID mode on the 5-port HPM-XA using DIP switch

Recommended to be used on operating system without JMicron HW RAID

Manager support like Linux, Mac & Solaris. Windows users can also use the

procedure below.

Note: Steps A to D need to be performed each time the raid mode is modified.

a. Set the DIP switch as shown below.

b. Press the RAID setting button with a ball point pen.

c. While pressing the RAID setting button turn on the system power

where the HPM is connected. The buzzer will sound while holding the

RAID setting button. Release it after at least 5 seconds for hardware

initialization. A single beep will be heard to indicate initialization is

completed. The above steps act as a reset.

d. Power off the system power.

1 2 3 4 5

SW1

BZS EZ M2 M1 M0

OFF

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

e. On the DIP switch, change (M0 to M2) setting to the

desired RAID mode using the diagram below.

All settings on the diagram shows

• Error buzzer function is ENABLED

• EZ function is DISABLED.

1 2 3 4 5

SW1

BZS EZ M2 M1 M0

RAID 0 Mode

1 2 3 4 5

SW1

BZS EZ M2 M1 M0

Clone Mode

1 2 3 4 5

SW1

BZS EZ M2 M1 M0

RAID 1& RAID 10 Mode

1 2 3 4 5

SW1

BZS EZ M2 M1 M0

Large Mode

1 2 3 4 5

SW1

BZS EZ M2 M1 M0

RAID 3 Mode

1 2 3 4 5

SW1

BZS EZ M2 M1 M0

Individual Drives Mode

1 2 3 4 5

SW1

BZS EZ M2 M1 M0

RAID 5 Mode

OFF

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

f. Press the RAID setting button with a ball point pen.

g. While pressing the RAID setting button turn on the system power

where the HPM is connected. The buzzer will sound while holding the

RAID setting button. Release it after at least 5 seconds for hardware

initialization. A single beep will be heard to indicate initialization is

completed.

h. Verify if the RAID array is detected by the system.

i. If the 5-port HPM-XA is connected to the motherboard onboard

SATA, on the CMOS setup utility, the raid array will display as

“Addonics H/W RAID5” if setup as a RAID5 array.

j. If the 5-port HPM-XA is connected to an eSATA host controller card,

on the RAID BIOS, the raid array will display as “Addonics H/W

RAID0” if setup as a RAID0 array.

k. If booted into Windows, in Disk Drives under Device Manager, the

raid array will display as “Addonics H/W LARGE” if setup as a

LARGE array.

l. Once raid array is verified, you can set the buzzer either ON or OFF.

1 2 3 4 5

SW1

BZS EZ M2 M1 M0

RAID 1& RAID 10 Mode

1 2 3 4 5

SW1

BZS EZ M2 M1 M0

Clone Mode

When 2 drives are

connected to the HPM-XA,

and DIP switch is set to this

setting, the 2 drives will be

configured as a 2-drive

RAID1 array.

Clone’s action is similar to

RAID1. However, all of the

hard drives will be mirrored.

Clone mode is useful

especially when users like

to copy data from a source

hard drive to the drives

connected to the HPM-XA.

RAID Setting Notes:

When 4 drives are connected to the HPM-XA, the 4 drives will be

configured as a 4-drive RAID10 array.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

f. Press the RAID setting button with a ball point pen.

g. While pressing the RAID setting button turn on the system power

where the HPM is connected. The buzzer will sound while holding the

RAID setting button. Release it after at least 5 seconds for hardware

initialization. A single beep will be heard to indicate initialization is

completed.

h. Verify if the RAID array is detected by the system.

i. If the 5-port HPM-XA is connected to the motherboard onboard

SATA, on the CMOS setup utility, the raid array will display as

“Addonics H/W RAID5” if setup as a RAID5 array.

j. If the 5-port HPM-XA is connected to an eSATA host controller card,

on the RAID BIOS, the raid array will display as “Addonics H/W

RAID0” if setup as a RAID0 array.

k. If booted into Windows, in Disk Drives under Device Manager, the

raid array will display as “Addonics H/W LARGE” if setup as a

LARGE array.

l. Once raid array is verified, you can set the buzzer either ON or OFF.

Notes on Spare Drives using the Easy RAID Setting (EZ)

When EZ function is ENABLED, the auto-rebuilding to spare drive is automatic.

The degraded RAID group will start rebuilding automatically by using the existing

spare drive.

* Spare drive can be either plugged before RAID building or a new drive can be plug

as the spare drive when RAID rebuild is required.

A. Which port acts as a spare drive?

The last drive will automatically become the spare drive.

For a 3-drive RAID5 with spare:

Drives connected to SATA ports 1~3 belong to the active RAID5

array and drive connected to port 4 is the spare.

For a 4-drive RAID10 with spare:

Drives connected to SATA ports 1~4 belong to the active RAID10

array and drive connected to port 5 is the spare.

For a 2-drive RAID1 with spare:

Drives connected to SATA ports 1& 4 belong to the active RAID1

array and drive connected to port 5 is the spare.

B. When will rebuild action start?

• When the raid fails and EZ is enabled, the HPM-XA will

automatically rebuild the RAID group using the spare.

• When the raid fails and EZ is disabled, the HPM-XA will NOT

rebuild the raid group unless you install a good drive to replace the

failed drive.

Connecting the Power Cable and RAID Tower to the

Computer

a. Connect the power cord provided from the wall

outlet to the back of the tower.

b. Make sure the power is off (power LED light

should be off).

c. Connect the infiniband cable from the back of

the tower to the multilane connector on the

computer.

Power on/off control

a. A main power switch is located at the back of

the tower. Turn the switch on. Another auxiliary

switch is located on the front of the tower.

b. Make sure the power is off on the auxiliary

switch (power LED light should be off).

c. Power on the tower.

Power

Connector

Power

Switch

Power

Switch

Back

Bottom Front

HDD LEDs

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Addonics Technologies

Addonics Technologies

Addonics Technologies RT5835HMEU Instrucciones de montaje

Addonics Technologies

Addonics Technologies RT93SNDHMS Manual de usuario

Addonics Technologies

Addonics Technologies REDESP? REDESPU3 Manual de usuario

Addonics Technologies

Addonics Technologies AD25CFD Manual de usuario

Addonics Technologies

Addonics Technologies Sapphire Mobile Rack II Manual de usuario

Addonics Technologies

Addonics Technologies RT54S2HMEU Manual de usuario

Addonics Technologies

Addonics Technologies AEIDMD4U2 Manual de usuario

Addonics Technologies

Addonics Technologies RT134SDEU3 Manual de usuario

Addonics Technologies

Addonics Technologies AERD25SN35 Manual de usuario

Addonics Technologies

Addonics Technologies RT3DAHEU3 Manual de usuario

Addonics Technologies

Addonics Technologies AE25SNSP Manual de usuario

Addonics Technologies

Addonics Technologies SCCHDSAU64 Manual de usuario

Addonics Technologies

Addonics Technologies RCHD256ES Manual de usuario

Addonics Technologies

Addonics Technologies CRT535PES Manual de usuario

Addonics Technologies

Addonics Technologies ST45HPMXA-B Manual de usuario

Addonics Technologies

Addonics Technologies JCCHDIF128 Manual de usuario

Addonics Technologies

Addonics Technologies RCHDSAES Manual de usuario

Addonics Technologies

Addonics Technologies DCHDIES Manual de usuario

Addonics Technologies

Addonics Technologies AD25MSD Manual de usuario

Addonics Technologies

Addonics Technologies RCED256ES Manual de usuario

Addonics Technologies

Addonics Technologies Sapphire Cipher II Snap-In SSN6G-256EU Manual de usuario

Addonics Technologies

Addonics Technologies External CipherChain Manual de usuario

Addonics Technologies

Addonics Technologies AJCHDIU Manual de usuario

Addonics Technologies

Addonics Technologies Jupiter ExDrive Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario