Addonics Technologies UDFH7 Manual de usuario

Technical Support

If you need any assistance to get your unit functioning properly, please have your

product information ready and contact Addonics Technical Support at:

Hours: 8:30 am - 6:00 pm PST

Phone: 408-453-6212

Email: http://www.addonics.com/support/query/

www.addonics.com

User Guide

1:7 USB HDD / Flash Duplicator

(UDFH7)

T E C H N O L O G I E S

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Unpacking and Overview

Power Cord (US Version Shown)

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Compatibility

Duplicator is USB 2.0 compliant. Works with USB 3.0 devices at 480Mb/s.

Works with the following devices:

- USB Flash media drive

- USB External hard disk

- Addonics Pocket Ultra DigiDrive (including PCMCIA storage devices or

flash

storage with the Addonics adapters)

- Addonics Pocket eSATA/USB DigiDrive

- Addonics Pocket Micro SATA UDD

- Addonics Diamond or Ruby ExDrive, with or without Cipher feature, using

the Addonics USB 3.0 to eSATAp Adapter

- Any of the above USB storage devices used with the Addonics CipherUSB

NOTE: Using an external power supply with storage devices that support

external power is strongly recommended.

Using the Duplicator with Adapters not supplied by Addonics is not

supported or recommended.

Duplicating source media encrypted using the Addonics Cipher family of

products can be done without using the Cipher hardware – which will result

in encrypted duplicates. This requires the Setup option Copy Area to be set

to “Whole Media.”

The Duplicator can copy media formatted as FAT16, FAT32, NTFS, ext2 or

ext3 with the Setup option Copy Area set to “System and Files.” Copying

NTFS media this way requires target media that is larger in capacity than the

source.

Quick Start

1. Insert the source device into the source slot, and any target devices

desired.

2. Turn on the unit.

3. After a self-diagnostic, the unit will scan all ports and start on the Copy

function.

4. Press OK to begin.

5. The Duplicator can operate in Asynchronous mode if it is able to contain

all of the source data in internal memory – about 200MB. Otherwise it will

operate in Direct mode.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

For Direct mode:

Once the Duplicator has analyzed the source device, it will scan for

suitable target devices. While examining connected targets, the port's green

LED will blink. If the device is suitable, the green LED will glow. If the device

is unsuitable, the red LED will glow. The Display will show how many targets

are ready.

Press OK once all of the targets are ready to begin copying. The

green LEDs will blink to indicate activity. Once copying is complete for a

target, the green LED will glow to indicate copy succeeded or the red LED

will glow to indicate the copy failed.

For Asynchronous mode (default):

Once the Duplicator has analyzed the source device, it will scan for

suitable target devices. While examining a target device, the green LED will

blink. If a target device is suitable, the green LED will continue to blink and

the copy process will begin immediately. When a target is finished, the green

LED will glow to indicate the copy succeeded, or the red LED will glow to

indicate the copy failed.

Once a target device's port LED is glowing green or red, the device

may be removed and another inserted in its place. The new device will be

examined and copying will proceed. The LCD Display will show an ongoing

tally of devices that passed and failed the copy process.

Duplicator Functions

The Duplicator menu has three sections: Main Menu, and Utility and Setup

which are accessed as Main Menu Items 6 and 7.

Main Menu

1. Copy

Performs the Copy process as described in the Quick Start section. When

the Copy function is on the menu display, it also shows the current setting for

the Copy Area function in the Setup Menu: (Data) for the “System and Files”

setting, or (Whole) for the “Whole Media” setting. For details, see 7.2. Copy

Area.

2. Compare

Performs a full comparison between the target devices and the source

device.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

3. Copy+Compare

Performs both the Copy and Compare functions in a single step. Between

the two functions the devices are all powered down for a duration set by the

Power Off Time Between Copy+Compare function in the Setup menu.

Copy+Compare does not display the Copy Area setting.

4. Capacity Check

Performs a basic test on target devices to determine if they are functioning

properly. Does not report the status of the source device. Displays pass and

fail counts, and number of drives remaining to test under “Capacity” when in

progress. When complete, each target port will show a green or red LED

glowing to indicate which devices pass or fail. Using the arrow keys will

show the status or capacity of each device.

Capacity Check does work in Asynchronous mode, so once it's been

activated, target devices can be removed when finished and more target

devices can be inserted.

NOTE: NEVER remove a device while the LED is blinking.

5. Information

The Information function is actually a sub-menu with two functions:

5.1. USB Info.

Pressing OK for USB info will begin with a port number (beginning with [1],

which is the SOURCE port). Use the arrow buttons to move between ports.

As each port is selected, the unit will read a device if present, and report on

the capacity and file system found on that port.

5.2. System Info.

Displays the type of duplicator (by source and target count, for example 1-7)

and the firmware version.

Utility Menu

6.1. Do Format

Formats the target media using the following sub-options:

6.1.1. Auto Format

The Duplicator will format the media using the following rules:

If the media is formatted using one partition of either FAT16 or FAT32, the

unit will simply reformat the media the same way.

If the media is not formatted using a FAT file system, it will be formatted as

FAT16 if the capacity is under 2GB, or FAT32 if greater than 2TB.

6.1.2. FAT Format

The Duplicator will format the media as FAT16.

6.1.3. FAT32 Format

The Duplicator will format the media as FAT32.

Having chosen one of the three sub-options, press OK once more to confirm

the choice or ESC to cancel.

NOTE: NEVER remove a device while the LED is blinking.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

6.2. Measure Speed

Estimates the read and write speed of the target media. After selecting this

function, the port number in use will appear on the LCD, beginning with Port

2 (the first target). Press the arrow buttons to switch between targets. Once a

target is detected, the test will continue to run without accepting any more

input until it is complete, then provide a short report on the read and write

speed for the media found.

NOTE: NEVER remove a device while the LED is blinking.

6.3. Media Check

Performs a full examination of all space on target media using the following

sub-options:

6.3.1. H3 Safe

Performs a read-only examination of media, without harming any data.

6.3.2. H5 R/W

Performs a destructive read-write examination of media.

6.3.3. Setup Range

This option determines how much of the media is examined by the Media

Check, expressed as a percentage. This percentage is shown in the Media

Check menu for the Safe and R/W options. Default setting is 100%.

6.3.4. Set Error Limit

This option determines how much of the tested media may show an error

before a media is counted as a FAIL. Expressed as a percentage of the

tested area. The Default setting is 0.

Media Check uses Asynchronous Mode, meaning devices may be removed

once tested and new media may be inserted after the process begins.

NOTE: NEVER remove a device while the LED is blinking.

6.4. Quick Erase

Erases all content on all target media, leaving the file system intact. Quick

Erase only works on FAT16 or FAT32 file systems. Media formatted using

other file systems will fail, leaving the data intact. Works in Asynchronous

Mode, meaning media may be removed once erased and more may be

inserted later.

NOTE: NEVER remove a device while the LED is blinking.

6.5. Full Erase

Erases all content on target media completely by overwriting all blocks with

zeros, leaving the media unformatted when complete. Works in Asynchro-

nous Mode, meaning media may be removed once erased and more may be

inserted later.

NOTE: NEVER remove a device while the LED is blinking.

6.6. DoD Erase

Performs a 3-pass sanitization of all media blocks compliant with DoD

5220.22-M standards.

6.7. System Update

Performs a firmware update to the unit. Update procedure details to be

released with the update itself. Briefly, insert a media into the device contain-

ing the binary firmware image, then press OK. When the process is complete,

turn the unit completely off, wait five seconds, then turn the unit back on.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

6.8. Calc. Checksum

Calculates a checksum value for the Copy Area function defined in the

Setup Menu.

NOTE: This function is not to be used to validate copies. Media that have

identical content and structure may still have different checksums. Testing

media devices for accurate duplication should only be done using the

Compare function.

Setup Menu

7.1. Startup Menu

Defines the function that will appear by default after power-on testing is

completed. Any of the Main Menu functions may be selected.

Default is 1. Copy.

7.2. Copy Area

Determines the method for copying from the source device to the target

devices: “Whole Media” copies the entire device, sector-by-sector – without

any regard to the contents. “System and Files” copies only the contents of

file systems understood by the firmware: FAT16, FAT32, NTFS, ext2 or ext3.

File systems not recognized by the firmware will be copied using the “Whole

Media” method.

Default is “System and Files.”

7.3. Button Beep

Enables or disables the unit sounding a “beep” noise when buttons are

pressed.

7.4. Asyn Hold Time

During operations that use Asynchronous Mode, this setting determines the

delay after all media have been removed before confirming that an operation

is complete. Once that delay has been expired, the operation will halt and

the display will request confirmation to exit the function. Press OK to confirm

the exit, ESC to resume the function.

Settings are “Turn OFF” to disable this feature, meaning Asynchronous

functions will continue indefinitely until ESC is pressed, or a selection of

delay in seconds or minutes.

Default is “Turn OFF.”

7.5. Target Tolerance

Used to define the acceptable difference in capacity during the copy func-

tion, using one of three settings:

No Limit: Target capacity will not be considered before proceeding.

100% Same: Target capacity will be considered suitable only if the capacity

is identical to the source.

Allow tolerance: Selecting this option offers two additional choices: Set UP

Limit allows either “No Limit” or a percentage greater than the source

capacity. Set LOW Limit allows either “No Limit” or a percentage less than

the source capacity.

The Target Tolerance menu item displays the current setting in parentheses.

Default is “No Limit.”

NOTE: The size of the file system on the source is always duplicated with all

contents. Target devices greater than or less than the source capacity will

not reflect any changes to correct the difference.

www.addonics.com

Phone: 408-573-8580

Fax: 408-573-8588

Email: http://www.addonics.com/sales/query/

7.6. Asynchronous

Enables or disables Asynchronous Mode during the copy function. When

enabled, the Copy, Compare, and Copy+Compare functions will work as

described by the Quick Start section of this User Guide. When disabled,

the Copy, Compare, and Copy+Compare functions will work as described

in the Quick Start section of this User Guide in Direct Mode only.

Default is “Enable.”

7.7. Check Before Copy

Enables or disables testing target media before proceeding with the Copy

function.

Default is “Do Check” (enabled).

7.8. Power Off Time Between Copy+Compare

Determines the delay in seconds between the Copy and Compare func-

tions during Main Menu function 3. Copy+Compare.

Default is 3 (seconds).

7.9. Language

Sets the language used by the firmware's LCD display. Choices are

English or Japanese.

Default is English.

7.10. Working Mode

Determines the approximate rate at which the Duplicator will attempt to

copy media. Faster settings may shorten copy time but result in higher

failure rates, slower settings will cause the process to take longer but will

improve the reliability of the copy.

Default is “Normal Mode.” Choices are: Slowest, Slower, Normal, Faster,

Fastest.

7.11. Set HDD Mode

When enabled, all target devices will be required to be equal to or greater

than the capacity of the source, overriding “LOW Limit” tolerance settings

(see 7.5. Target Tolerance).

7.12. Restore Default

Returns all settings to their factory default values.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Duplicadora de discos de Addonics Technologies

Addonics Technologies

Addonics Technologies DGBRC7 Manual de usuario

Addonics Technologies

Addonics Technologies UDFUDD7 Manual de usuario

Addonics Technologies

Addonics Technologies UDFHNVM7 Manual de usuario

Addonics Technologies

Addonics Technologies HDU11SAS Manual de usuario

Addonics Technologies

Addonics Technologies Jasper II 1S JD2-325SN Manual de usuario

Addonics Technologies

Addonics Technologies HDUS11325DX Manual de usuario

Addonics Technologies

Addonics Technologies HDUS11SNDX Manual de usuario

Addonics Technologies

Addonics Technologies DigiCopier III DGC3 Manual de usuario

Addonics Technologies

Addonics Technologies DGBR4DR11 Manual de usuario

Addonics Technologies

Addonics Technologies HDUS4SNDX-A Manual de usuario

Addonics Technologies

Addonics Technologies UDFHNVM15 Manual de usuario

Addonics Technologies

Addonics Technologies MSHDU11T Manual de usuario

Addonics Technologies

Addonics Technologies CFASTD5 Manual de usuario

Addonics Technologies

Addonics Technologies ZHDUESA Manual de usuario

Addonics Technologies

Addonics Technologies M2MSHD9H-2S Manual de usuario

Addonics Technologies

Addonics Technologies HDU11SITDR Manual de usuario

Addonics Technologies

Addonics Technologies DDU3SAS Manual de usuario

Addonics Technologies

Addonics Technologies DGC3 Manual de usuario

Addonics Technologies

Addonics Technologies Jasper II JD2P3 Manual de usuario

Addonics Technologies

Addonics Technologies HD4SNH Manual de usuario

Addonics Technologies

Addonics Technologies Jasper II 3M Manual de usuario

Addonics Technologies

Addonics Technologies Jasper II SID Manual de usuario

Addonics Technologies

Addonics Technologies HDUSI325AES Manual de usuario

Addonics Technologies

Addonics Technologies HDUSI325 Manual de usuario

Manuales populares de Duplicadora de discos de otras marcas

Riso

Riso CV Series Manual

MicroBoards Technology

MicroBoards Technology GX-2 Manual de usuario

Carry

Carry Pro118 Manual de usuario

CopyPro

CopyPro PowerPro II Manual de usuario

Primera

Primera Max Manual de usuario

Logicube

Logicube EchoPlus-NG Manual de usuario

Silca

Silca Delta 2000 SA Manual de usuario

Reflex7

Reflex7 Daisy Chain Series Manual de usuario

Vinpower Digital

Vinpower Digital SharkCopier DC Manual de usuario

Codonics

Codonics Virtua E Manual de usuario

Octave

Octave Copy Master II Manual de usuario

Kanguru

Kanguru U2-DVDDUPE-S Manual de usuario

StarTech.com

StarTech.com 8STSATDUP11 Manual de usuario

DUPLO SEIKO CORPORATION

DUPLO SEIKO CORPORATION Duprinter DP-460 Manual de usuario

Vinpower Digital

Vinpower Digital MiniLoader VDX-1 Manual de usuario

MicroBoards Technology

MicroBoards Technology Quic Disc QD-2 Manual de usuario

Telex

Telex SpinWise Manual de usuario

Aleratec

Aleratec 260206 Manual de usuario