ADB L-807 Manual de usuario

L-807 Wind Cone

Style I-A, I-B, II, Size 1 and Size 2

User Manual

96A0345

Retain for future use.

Rev. K, 4/29/13

ETL Certified to FAA Specification

AC 150/5345-27 (Current Version)

and

FAA Engineering Brief 67

(Current Version)

L-807 Wind Cone 96A0345 Rev. K

History of Change 4/29/13

Disclaimer Table of

Contents Safety Introduction

History of

Change

Installation Operation Parts Schematics

Disclaimer

This manual could contain technical inaccuracies or typographical errors. ADB Airfield Solutions reserves the right to

revise this manual from time to time in the contents thereof without obligation of ADB Airfield Solutions to notify any

person of such revision or change.

Details and values given in this manual have been compiled with care. They are not binding, however, and ADB

Airfield Solutions disclaims any liability for damages or detriments suffered as a result of reliance on the information

given herein or the use of products, processes or equipment to which this manual refers. No warranty is made that

the use of the information or of the products, processes or equipment to which this manual refers will not infringe any

third party's patents or rights.

Warranties

LED Products of ADB Airfield Solutions manufacture are guaranteed against mechanical, electrical, and physical

defects for a period of four years after the date of installation and are guaranteed to be merchantable and fit for the

ordinary purposes for which such products are made.

ADB Airfield Solutions will correct by repair or replacement, at its option, equipment or parts which fail because of

mechanical, electrical or physical defects, provided that the goods have been properly handled and stored prior to

installation, properly installed and properly operated after installation, and provided further that Buyer gives ADB

Airfield Solutions written notice of such defects after delivery of the goods to Buyer. Refer to the Safety section for

more information on Material Handling Precautions and Storage precautions that must be followed.

ADB Airfield Solutions reserves the right to examine goods upon which a claim is made. Said goods must be

presented in the same condition as when the defect therein was discovered. ADB Airfield Solutions further reserves

the right to require the return of such goods to establish any claim.

ADB Airfield Solutions’ obligation under this guarantee is limited to making repairor replacement within a reasonable

time after receipt of such written notice and does not include any other costs such as the cost of removal of defective

part, installation of repaired product, labor or consequential damages of any kind, the exclusive remedy being to

require such new parts to be furnished.

ADBAirfieldSolutions’liabilityundernocircumstanceswillexceedthecontractpriceofgoodsclaimedtobedefective.

Any returns underthis guaranteeare to be on a transportation charges prepaid basis. For products not manufactured

by, but sold by ADB Airfield Solutions, warranty is limited to that extended by the original manufacturer.

This is ADB AirfieldSolutions’ sole guaranteeand warranty with respect tothegoods; there are noexpress warranties

or warranties of fitness for any particular purpose or any implied warranties of fitness for any particular purpose or any

implied warranties other than those made expressly herein. All such warranties being expressly disclaimed.

Trademarks

General notice: other product names used here are for identification purposes only and may be trademarks of their

respective companies.

Proprietary Information

This information carrier contains proprietary information, which shall not be used for other purposes than those for

which it has been released, nor be reproduced or disclosed to third parties without the prior written consent of ADB

Airfield Solutions.

Nopartofthispublicationmaybereproduced,storedinaretrievalsystem, or transmittedinanyformor by any means,

mechanical, photocopy, recording, or otherwise, without the prior written permission of ADB Airfield Solutions. No

patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed

for damages resulting from the use of the information contained herein.

ADB Airfield Solutions shall not be liable to the purchaser of this product or third parties for damages, losses, costs,

or expenses incurred by purchaser or third parties as a result of accident, misuse, or abuse of this product or

unauthorized modifications, repairs, or alterations to this product. ADB Airfield Solutions shall not be liable against

any damages arising from the use of any options or parts other than those designated as approved products.

a.1 History of Change

PAGE REV DESCRIPTION EC NO. CHECKED APPROVED DATE

All E Updated parts and diagrams for APS 2987 JR DM 11/17/10

All F Updated maintenance, parts and diagrams 3/30/08

All G Updated schematics, maintenance and parts sections DR ER 1/9/09

All H Added Rotating Power Supply Parts

Added Kit install instructions 2297 DR ER 11/06/09

I Added new diagrams, pictures and parts DR ER 09/14/10

10x-11x J Updated parts and schematics DR ER 05/24/11

All K Updated incandescent and LED info and parts. 3852/3822 DR ER 04/23/13

96A0345 Rev. K L-807 Wind Cone

4/29/13 TOC

Schematics Parts Operation Installation Introduction

TOC Safety Table of

Contents Disclaimer

TABLE OF CONTENTS

a.1 History of Change ................................................................................................. ii

1.0: Safety...................................................................................................................1

1.1 To use this equipment safely ................................................................................1

1.1.1 Additional Reference Materials .....................................................................1

1.1.2 Qualified Personnel ......................................................................................1

1.1.3 Intended Use ................................................................................................1

1.1.4 Storage .........................................................................................................1

1.1.4.1 Operation............................................................................................. 2

1.1.4.2 Material Handling Precautions............................................................. 2

1.1.4.3 Action in the Event of a System or Component Malfunction................ 2

1.1.4.4 Maintenance and Repair...................................................................... 2

1.1.4.5 Operation of Overloaded Regulators................................................... 2

2.0: L-807 Introduction...............................................................................................3

2.1 Compliance with Standards ..................................................................................3

2.2 Uses ......................................................................................................................3

2.3 Features ................................................................................................................3

2.4 Lighting Assembly - LED .......................................................................................3

2.5 Lighting Assembly - Incandescent ........................................................................3

2.6 Operation ..............................................................................................................4

2.6.1 FAA Wind Cone Classifications ....................................................................4

2.7 Electrical Supply ....................................................................................................4

2.7.1 LED Current Driven ......................................................................................4

2.7.2 LED Voltage Driven ......................................................................................4

2.8 Dimensions ...........................................................................................................5

2.8.1 Internally Lighted ..........................................................................................5

2.8.2 Externally Lighted .........................................................................................5

2.8.3 Packing .........................................................................................................5

2.9 L-807 Wind Cone: Required Equipment ...............................................................6

2.10 Lighted Wind Cones ............................................................................................7

2.10.1 Externally Lighted Wind Cones ..................................................................7

2.10.2 Internally Lighted Wind Cone .....................................................................7

2.11 Unlighted Wind Cones ........................................................................................8

3.0: L-807 Wind Cone Installation.............................................................................9

3.1 Unpacking .............................................................................................................9

3.2 Tools/Equipment/Supplies Needed .......................................................................9

3.3 Mounting the Foundation ......................................................................................9

3.4 Assembly Procedures .........................................................................................12

3.4.1 L-807 Center Hinge-Pole Assembly ...........................................................12

3.4.2 L-807 Bottom Hinge-Pole Assembly ...........................................................14

3.4.2.1 Assembling Wind Cone Sock Cage................................................... 15

3.4.2.2 Assembling the Cage Assembly to the Shaft..................................... 16

3.5 Internally Lighted LED Wind Cone Kit Installation ...............................................17

3.5.1 Installing Rotary Power Assembly ..............................................................17

3.5.2 Installing the Internal LED Light Assembly .................................................19

3.6 Externally Lighted LED Wind Cone Kit Installation .............................................20

3.6.1 Installing Rotary Power Assembly ..............................................................20

3.6.2 Installing the External LED Light Assembly ................................................21

3.7 Assembling Wind Cone Shaft into Wind Cone Pole ............................................22

3.8 Attach the Windsock ...........................................................................................22

3.9 Optional Roof Mounting ......................................................................................23

3.10 Tether Mounting ................................................................................................24

3.11 Grounding the Wind Cone Pole ........................................................................24

L-807 Wind Cone 96A0345 Rev. K

TOC 4/29/13

Disclaimer Table of

Contents Safety Introduction

TOC Installation Operation Parts Schematics

3.12 Installation of FAA Light Bases – PA4 and L-830/831 Applications ..................25

4.0: Maintenance.......................................................................................................27

4.1 Lighted Wind Cones ............................................................................................27

4.1.1 Lubrication ..................................................................................................27

4.1.2 Structure .....................................................................................................27

4.1.3 Wind Cone Sock and Cage ........................................................................27

4.1.4 Wiring ..........................................................................................................27

4.1.5 Lowering the Pole Assembly ......................................................................27

4.1.6 Miscellaneous .............................................................................................27

4.2 Rotating Power Supply Bearing Replacement ....................................................28

4.2.1 Disassembly Instructions ............................................................................28

4.2.2 Assembly Instructions .................................................................................29

4.3 Replacing an LED Light Assembly ......................................................................30

4.4 Troubleshooting ...................................................................................................31

4.4.1 Voltage powered LED Wind Cone ...........................................................31

4.4.2 Current powered LED Wind Cone ...........................................................31

4.4.3 Part Replacement .......................................................................................31

4.5 Schematics .........................................................................................................32

5.0: Parts ..................................................................................................................43

5.1 Internally Lighted Halogen Wind Cone ................................................................44

5.2 Power Adapter Parts List .....................................................................................44

5.3 Internally Lighted LED Wind Cone ......................................................................45

5.4 Internally Lighted Halogen Wind Cone ................................................................47

5.5 Wind Cone Rotating Power Supply Assembly .....................................................49

5.6 Wind Cone Cages ...............................................................................................51

5.7 Possible Spare Parts ...........................................................................................53

5.7.1 Wind Cone LED Light Engine, Obstruction Light and Power Supply Board Replace-

ment Guide ..........................................................................................................55

96A0345 Rev. K L-807 Wind Cone

4/29/13 Safety

Schematics Parts Operation Installation Introduction

Safety Safety Table of

Contents Disclaimer

1.0 Safety This section contains general safety instructions for installing and using ADB Airfield Solutions equipment. Some

safety instructions may not apply to the equipment in this manual. Task- and equipment-specific warnings are

included in other sections of this manual where appropriate.

1.1 To use this

equipment safely

1.1.1 Additional Reference

Materials • C22.1 Canadian Electrical Code (latest rev)

• NFPA 70B, Electrical Equipment Maintenance.

• NFPA 70E, Electrical Safety Requirements for Employee Workplaces.

• ANSI/NFPA 79, Electrical Standards for Metalworking Machine Tools.

• OSHA 29 CFR, Part 1910, Occupational Health and Safety Standards.

• National and local electrical codes and standards.

1.1.2 Qualified Personnel The term qualified personnel is defined here as individuals who thoroughly understand the equipment and its safe

operation, maintenance and repair. Qualified personnel are physically capable of performing the required tasks,

familiar with all relevant safety rules and regulations and have been trained to safely install, operate, maintain and

repair the equipment. It is the responsibility of the companyoperating this equipment to ensurethat its personnel meet

these requirements.

Always use required personal protective equipment (PPE) and follow safe electrical work practices.

1.1.3 Intended Use

ADB Airfield Solutions cannot be responsible for injuries or damages resulting from nonstandard, unintended

applications of its equipment. This equipment is designedand intended only for the purpose described in this manual.

Uses not described in this manual are considered unintended uses and may result in serious personal injury, death

or property and equipment damage. Unintended uses may result from taking the following actions:

• Making changes to equipment that are not recommended or described in this manual or using parts that are not

genuine ADB Airfield Solutions replacement parts.

• Failing to make sure that auxiliary equipment complies with approval-agency requirements, local codes and all

applicable safety standards.

• Using materials or auxiliary equipment that are inappropriate or incompatible with ADB Airfield Solutions

equipment.

• Allowing unqualified personnel to perform any task.

1.1.4 Storage

WARNING

Read installation instructions in their entirety before starting installation.

• Refer to the FAA Advisory Circular AC 150/5340-26, Maintenance of Airport Visual Aids Facilities, for

instructions on safety precautions.

• Observe all safety regulations. To avoid injuries, always disconnect power before making any wiring

connections or touching any parts. Refer to FAA Advisory Circular AC 150/5340-26.

• Become familiar with the general safety instructions in this section of the manual before installing,

operating, maintaining or repairing this equipment.

• Read and carefully follow the instructions throughout this manual for performing specific tasks and

working with specific equipment.

• Make this manual available to personnel installing, operating, maintaining or repairing this equipment.

• Follow all applicable safety procedures required by your company, industry standards and government

or other regulatory agencies.

• Install all electrical connections to local code.

• Use only electrical wire of sufficient gauge and insulation to handle the rated current demand. All wiring

must meet local codes.

• Route electrical wiring along a protected path. Make sure they will not be damaged by moving

equipment.

• Protect components from damage, wear, and harsh environment conditions.

• Allow ample room for maintenance, panel accessibility, and cover removal.

• Protect equipment with safety devices as specified by applicable safety regulations.

• If safety devices must be removed for installation, install them immediately after the work is completed

and check them for proper functioning prior to returning power to the circuit.

WARNING

Using this equipment in ways other than described in this manual may result in personal injury, death or

property and equipment damage. Use this equipment only as described in this manual.

CAUTION

If equipment is to be stored prior to installation, it must be protected from the weather and kept free of

condensation and dust.

Failure to follow this instruction can result in injury or equipment damage.

L-807 Wind Cone 96A0345 Rev. K

To use this equipment safely 4/29/13

Disclaimer Table of

Contents Safety Introduction

To use this

equipment

Installation Operation Parts Schematics

1.1.4.1 Operation

1.1.4.2 Material Handling

Precautions

1.1.4.3 Action in the Event of a

System or Component

Malfunction

1.1.4.4 Maintenance and Repair

1.1.4.5 Operation of

Overloaded Regulators

WARNING

• Only qualified personnel, physically capable of operating the equipment and with no impairments in

their judgment or reaction times, should operate this equipment.

• Read all system component manuals before operating this equipment. A thorough understanding of

system components and their operation will help you operate the system safely and efficiently.

• Before starting this equipment, check all safety interlocks, fire-detection systems, and protective

devices such as panels and covers. Make sure all devices are fully functional. Do not operate the

system if these devices are not working properly. Do not deactivate or bypass automatic safety

interlocks or locked-out electrical disconnects or pneumatic valves.

• Protect equipment with safety devices as specified by applicable safety regulations.

• If safety devices must be removed for installation, install them immediately after the work is completed

and check them for proper functioning.

• Route electrical wiring along a protected path. Make sure they will not be damaged by moving

equipment.

• Never operate equipment with a known malfunction.

• Do not attempt to operate or service electrical equipment if standing water is present.

• Use this equipment only in the environments for which it is rated. Do not operate this equipment in

humid, flammable, or explosive environments unless it has been rated for safe operation in these

environments.

• Never touch exposed electrical connections on equipment while the power is ON.

CAUTION

This equipment may contain electrostatic sensitive devices.

• Protect from electrostatic discharge.

• Electronic modules and components should be touched only when this is unavoidable e.g. soldering,

replacement.

• Before touching any component of the cabinet you should bring yourbody to the same potential as the

cabinet by touching a conductive earthed part of the cabinet.

• Electronic modules or components must not be brought in contact with highly insulating materials such

as plastic sheets, synthetic fiber clothing. They must be laid down on conductive surfaces.

• The tip of the soldering iron must be grounded.

• Electronic modules and components must be stored and transported in conductive packing.

WARNING

• Do not operate a system that contains malfunctioning components. If a component malfunctions, turn

the system OFF immediately.

• Disconnect and lock out electrical power.

• Allow only qualified personnel to make repairs. Repair or replace the malfunctioning component

according to instructions provided in its manual.

WARNING

Allow only qualified personnel to perform maintenance, troubleshooting, and repair tasks.

• Onlypersonswhoareproperlytrainedandfamiliarwith ADB Airfield Solutionsequipmentare permitted

to service this equipment.

• Disconnect and lock out electrical power.

• Always use safety devices when working on this equipment.

• Follow the recommended maintenance procedures in the product manuals.

• Do not service or adjust any equipment unless another person trained in first aid and CPR is present.

• Connect all disconnected equipment ground cables and wires after servicing equipment. Ground all

conductive equipment.

• Use only approved ADB Airfield Solutions replacement parts. Using unapproved parts or making

unapproved modifications to equipment may void agency approvals and create safety hazards.

• Check interlock systems periodically to ensure their effectiveness.

• Do not attempt to service electrical equipment ifstanding water is present. Use caution when servicing

electrical equipment in a high-humidity environment.

• Use tools with insulated handles when working with electrical equipment.

WARNING

• Operation of a Regulator while overloaded at any step may result in equipment failure or equipment

damage.

96A0345 Rev. K L-807 Wind Cone

4/29/13 L-807 Introduction

Schematics Parts Operation Installation Introduction Safety Table of

Contents Disclaimer

2.0 L-807

Introduction

2.1 Compliance with

Standards FAA: L-807 & L-807(L) AC 150/5345-27 (Current Edition) and the FAA Engineering Brief No.

67 “Light Sources other than Incandescent and Xenon for Airport Lighting and Obstruction

Lighting Fixtures.” ETL Certified.

2.2 Uses Provides visual surface wind direction and velocity information to pilots in flight or on the

ground at airports and heliports.

2.3 Features •The L-807 wind cone is a non-frangible designed wind cone available in three styles,

lighted (internal or external) or unlighted, and in two sizes, eight- or twelve-foot wind

socks.

•Pole is available with either a center hinge or bottom hinge. Center hinge allows easier

pole lowering. Bottom hinge includes a swing-out support leg that allows the mast to be

lowered to a convenient servicing height for light source replacement.

•The LED lighted wind cone assemblies may be powered directly from a 2.8-6.6 A or 8.5-

20 A series circuit using only an isolation transformer. No power adapter is needed,

significantly reducing CCR load. It may also be powered from a direct 95-264 VAC

source. LED light output stays constant regardless of input current range (for series

powered) or input voltage level (for voltage powered) wind cones.

•Any AC voltage-powered incandescent wind cone may be powered from a 6.6 A or 20 A

series circuit using an ADB power adapter or from a direct 120 VAC source.

•Sealed bearings allow precision vane operation for true wind direction in all types of

weather and wind conditions.

•Bearing covers are provided for additional bearing protection against dirt and moisture.

•The nylon fabric sock is treated for water repellency and resistance to rot and mildew.

•Standard colors are orange or orange/white banded and the colorfastness exceeds

Method 5671 of Federal Standard 191. Other colors are available as a special order.

•An optional L-810(L) red LED obstruction light is available (see catalog sheet 2063). For

wind cone configurations available with an LED L-810(L), see ordering code.

2.4Lighting Assembly

- LED — The internally lighted wind cone provides an average illumination on the top and

lateral surface of a fully extended windsock of 10- to 30-ft lamberts. The internally

lighted 8-foot wind cone uses one LED optical assembly and the 12-ft uses three LED

optical assemblies.

— The externally lighted wind cone provides a minimum illumination of 2 foot candles on

the upper surface of the fully extended windsock. The externally lighted 8- and 12-foot

wind cones use two LED optical assemblies.

— The wind sock is illuminated with orange LEDs and is used only on solid orange

colored wind socks.

2.5Lighting Assembly

- Incandescent — The internally lighted wind cone consists of two 100 W/

120 VAC lamps for an 8-foot wind cone or three 100 W/

120 VAC lamps for a 12-foot wind cone

— An incandescent lighted wind cone cage may be provided with an optional L-810(L)

LED red obstruction light.

— The incandescent wind cone can be used on any solid colored or color-banded wind

sock.

WARNING

Read the instructions in their entirety before starting installation or attempting any

maintenance.

L-807 Wind Cone 96A0345 Rev. K

Operation 4/29/13

Disclaimer Table of

Contents Safety Introduction Installation Operation Parts Schematics

2.6 Operation The operation of the wind cone is entirely dependent on the direction and relative velocity of

the surface wind. Movement of the wind through the open throat of the cage and into the sock

causes the tail to inflate. The tail of the inflated sock indicates true wind direction for velocities

as low as three knots through a 360° circle about the vertical shaft.

2.6.1 FAA Wind Cone

Classifications

2.7 Electrical Supply

2.7.1 LED Current Driven For 6.6 A or 20 A, 60 Hz circuits, a 150 W or 200 W L-830 transformer with appropriate

primary input (i.e. 6.6 or 20 A) must be selected. Use 150 W or 200 W L-831 series

for 50 Hz circuits.

2.7.2 LED Voltage Driven

Size 1: 8 foot

Size 2: 12 foot

Style I-A: Externally Lighted

Style I-B: Internally Lighted

Style II: Unlighted

L-807 LED Fixture Load Isolation

Transformer Isolation Load

Transformer CCR Load

Internally Lit, 8-ft

Without L-810 79VA 150W 18VA 97VA

With LED L-810(L) 87VA 150W 20VA 107VA

Externally Lit, 8-ft

Without L-810 87VA 200W 26VA 113VA

With LED L-810(L) 102VA 200W 27VA 129VA

Internally Lit, 12-ft

Without L-810 96VA 20W 25VA 121VA

With LED L-810(L) 110VA 200W 23VA 133VA

Externally Lit, 12-f

Without L-810 87VA 200W 26VA 113VA

With LED L-810(L) 102VA 200W 27VA 129VA

Input voltage: 95V AC (min.) - 264V AC (max.), 50/60Hz

8-foot Internally Lit Externally Lit

Maximum input power:

Without L-810 69VA 80VA

With LED L-810(L) 75VA 87VA

12 foot Internally Lit Externally Lit

Maximum input power:

Without L-810 95VA 80VA

With LED L-810(L) 109VA 87VA

96A0345 Rev. K L-807 Wind Cone

4/29/13 Dimensions

Schematics Parts Operation Installation Introduction Safety Table of

Contents Disclaimer

2.8 Dimensions

2.8.1 Internally Lighted

2.8.2 Externally Lighted

Figure 1: L-807 Heights

2.8.3 Packing

Wind Cone Type Overall Height Height 1 Height 2

Halogen 8 ft 232.25 in (589.9 cm) 40.25 in (102.2 cm) 192 in (487.7 cm)

Halogen 12 ft 250.25 in (635.6 cm) 48.25 in (122.5 cm) 192 in (487.7 cm)

LED 8 ft 245.2 in (622.8 cm) 53.2 in (135.1 cm) 192 in (487.7 cm)

LED 12 ft 263.4 in (669.0 cm) 71.4 in (181.4 cm) 192 in (487.7 cm)

Wind Cone

Type Overall Height Height 1 Height 2 Height 3 Height 4

LED 8 ft 245.2 (622.8) 11.2 (28.5) 23.9 (60.7) 18 (45.7) 192 (487.7)

LED 12 ft 267.5 (679.5) 15.5 (61.2) 24.1 (127) 36 (91.4) 192 (487.7)

35.4

72.9

17.7

Overall Height

Height 1

Height 2

Description Quantity Per Box Dimensions

(H x W x D) Weight lb/kg

8-ft. Wind Cone

Lighted 1 Pole

1 Basket

16.6 x 10 x 10 in / 502.9 x 25.4 x 25.4 cm

20 x 20 x 15 in / 50.8 x 50.8 x 38.1 cm

150 lb / 68 kg

47 lb / 21.3 kg

8-ft. Wind Cone

Unlighted 1 Pole

1 Basket

16.6 x 10 x 10 in / 502.9 x 25.4 x 25.4 cm

20 x 20 x 15 in / 50.8 x 50.8 x 38.1 cm

135 lb / 61.2 kg

42 lb / 19.1 kg

12-ft. Wind Cone

Lighted

1 Pole

1 Basket

Hardware

16.6 x 10 x 10 in / 502.9 x 25.4 x 25.4 cm

45 x 42 x 6 in / 114.3 x 106.7 x 15.2 cm

20 x 20 x 15 in / 50.8 x 50.8 x 38.1 cm

150 lb / 68 kg

47 lb / 21.3 kg

45 lb / 20.4 kg

12-ft. Wind Cone

Unlighted

1 Pole

1 Basket

Hardware

16.6 x 10 x 10 in / 502.9 x 25.4 x 25.4 cm

45 x 42 x 6 in / 114.3 x 106.7 x 15.2 cm

20 x 20 x 15 in / 50.8 x 50.8 x 38.1 cm

135 lb / 61.2 kg

42 lb / 19.1 kg

45 lb / 20.4 kg

L-807 Wind Cone 96A0345 Rev. K

L-807 Wind Cone: Required Equipment 4/29/13

Disclaimer Table of

Contents Safety Introduction Installation Operation Parts Schematics

2.9 L-807 Wind Cone:

Required Equipment Refer to Table 1 for required equipment that is supplied. Refer to Table 2 for required

equipment that is not supplied. Refer to the Parts section for ordering information.

Table 1: Required Equipment Supplied

Table 2: Required Equipment Not Supplied

Description Quantity

L-807 wind cone assembly 1

Instruction manual 1 per order

Description Quantity

Wrenches for 3/8 inch, 1/2 inch, and 5/8 inch hex screws and nuts 3

Allen hex keys for 5/64 inch, 3/16 inch and 1/4 inch 3

Medium size blade screwdriver 1

Cloth for cleaning lamps As required

Grease gun 1

Saw Horse 1

Otros manuales para L-807

Tabla de contenidos

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario