Actiforce Aluforce Pro 140 M Manual de usuario

English

Deutsch

Nederlands

ALUFORCE

PRO 251 M

(90 Degree)

P4yA2L-2EN-DE-NL

Assembly Manual

for LEFT return

Read this manual thoroughly and store in a safe place!

Frame for a electro-motorized sit-stand workstation

Content

1 GENERAL ........................................................................................................................................................ 3

1.1 Local value of the assembly/operating manual ....................................................................................... 3

1.2 Intended use ............................................................................................................................................ 3

1.3 Improper use.....................................................................................................................................................3

1.4 Laws, directives and standards to be observed ....................................................................................... 3

1.5 FCC Information for Class B digital device (Power Supply) .................................................................. 3

1.6 Content box ......................................................................................................................................... 4-5

2 SAFETY INFORMATION ............................................................................................................................... 6

2.1 Symbols/warnings ................................................................................................................................... 6

2.2 Symbols used on the workstation frame ................................................................................................. 6

2.3 Organizational measures ........................................................................................................................ 6

2.4 Informal safety measures ........................................................................................................................ 6

2.5 Note for those assembling the workstation ............................................................................................. 6

2.6 Transport and assembly.......................................................................................................................... 6

2.7 Use of the workstation frame .................................................................................................................. 7

2.8 Specific dangers ...................................................................................................................................... 7

2.9 In an emergency ...................................................................................................................................... 7

2.10 Maintenance and upkeep ........................................................................................................................ 8

2.11 Cleaning .................................................................................................................................................. 8

2.12 Persistent risks ........................................................................................................................................ 8

3 ASSEMBLY ...................................................................................................................................................... 9

3.1 Checking the items supplied ................................................................................................................... 9

3.2 Packaging ................................................................................................................................................ 9

3.3 Tightening torques for screws used......................................................................................................... 9

3.4 Assembly of the workstation ................................................................................................................... 9

3.4.1 Pre-assembly of the Crossbar ............................................................................................................... 9

3.4.2 Mounting the Feet ............................................................................................................................. 10

3.4.3 Mounting the Bottom Crossbar ..................................................................................................... 11-12

3.4.4 Mounting the Top Crossbar ..................................................................................................................13-14

3.4.5 Mounting the Top Support..........................................................................................................................15

3.4.6 Mounting the drive shaft Leg 1 & Leg 3 ............................................................................................ 16

3.4.7 Mounting the drive shaft & Gearbox Leg 2 ........................................................................................ 17

3.4.8 Mounting the drive units ................................................................................................................... 18

3.4.9 Adjustment of the frame width ...................................................................................................... 19-20

3.4.10 Connecting cable drive units ............................................................................................... 21

3.4.11 Frame test without tabletop ................................................................................................. 22

3.4.12 Note : Assembly of the tabletop ............................................................................................ 23

3.4.13 Note : Mounting the power supply underneath tabletop ....................................................... 23

3.4.14 Note : Identification sticker ................................................................................................ 23

4 TECHNICAL SPECIFICATIONS .......................................................................................................... 24-25

5 5 OPERATION AND INSICATORS ................................................................................................... .26

5.1 Indicators .......................................................................................................................................... 26

6 TROUBLESHOOTING .................................................................................................................................. 27

7 CUSTOMER SERVICE ................................................................................................................................. 28

8 MANUFACTURER ........................................................................................................................................ 28

9 RECYCLING .................................................................................................................................................. 28

9.1 Taking the workstation out of active duty ............................................................................................ 28

9.2 Taking the workstation apart ............................................................................................................... 28

9.3 Recycling ............................................................................................................................................... 28

1 General

1.1 Local value of the assembly/operating manual

The guiding principle for safe use and trouble-free operation of this workstation frame is knowledge

of basic safety information and regulations. This assembly/operating manual contains the most im-

portant information needed for assembling and operating the workstation frame safely. This assem-

bly/operating manual, in particular the safety information contained herein, must be observed by any

person building the frame and working on the finished surface. More importantly, the rules and reg-

ulations applying to accident prevention in the locality in which the workstation frame is to be used

must be observed at all times.

1.2 Intended use

The workstation frame must be used only as a height-adjustable workstation for sitting/standing use

in offices or other enclosed areas. The frame must be used for this purpose only. The workstation

frame may be set up and operated solely in office environments. Do not use the workstation frame

in the home. Please observe the provisions of Section 2, Safety Information. Children may be una-

ware of the dangers presented by the workstation frame if unsupervised. Any other use than the

above shall be deemed improper. The manufacturer can in no way be held liable for damage arising

from improper use.

Intended use shall also include:

 Observation of all information from the assembly/operating manual and

 Prohibition of any sort of addition to/conversion of the workstation.

1.3 Improper use

 Never use the workstation frame to lift people or loads.

 Do not exceed the maximum load of the workstation frame.

 Do not use the workstation frame in the home; alternatively, use it only in offices.

1.4 Laws, directives and standards to be observed.

 Machinery Directive 98/37/EC

 Low Voltage Directive 73/23/EEC

 Electromagnetic Compatibility Directive 89/336/EEC

 EN 12100, parts 1 and 2

 EN 294

1.5 FCC Information for Class B digital device (Power Supply)

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can ra-

diate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/TV technician for help.

WARNING: Any changes or modifications not expressly approved by the manufacturer

could void the user’s authority to operate the equipment.

# Part name Qty

01 Leg 3

02 Foot 2

03 Centre foot 1

04 Top support 2

05 Centre top support 1

06 Hexagon shaft Short + Long 2+2

07 Axle Drive Short + Long 1+1

08 Tools 1

09 90 degree gearbox 1

10 Foot adjuster 6

11 Bearing Cover 3

12 Mounting hardware kit 1

13 Straight bottom crossbar 1

14 90 degree bottom crossbar 1

15 Straight top crossbar 1

16 90 degree top crossbar 1

17 Cover bottom crossbar 4

18 Cover top crossbar 3

19 Drive Unit Master 1

20 Drive Unit Slave 1

21 Power supply 1

22 Power cord 1

23 Link cable drive unit 1

24 Cable keypad 1

25 Keypad up-dowm 1

1.6 Content box

12.1 12x M5x25

12.2 12x M6x25

12.3 12x M6x6

12.4 2x M6x16

12.5 10x M6x20

12.6 16x M6

12.7 12x Ø5

12.8 14x Ø6

12.9 20x M4.5x16

12.10 4x M4.5x20

12.11 2x M6x80

12.12 4x Spacer

12.13 4x Short

Slide Nut

12. Mounting Hardware Kit

12.14 1x Long

Slide Nut

12.15 1x M4x10

06 07

21 22 24 25

09 10 08 11

13 14 15 16

18 19 20

01 02 05 03 04

2 Safety Information

2.1 Symbols/warnings

The assembly/operating manual uses the following terms and signs to indicate dangers:

2.2 Symbols used on the workstation frame

2.3 Organizational measures

 The workstation frame can best be assembled by two people. Turning the frame, once

the work surface has been fitted, is a task in particular which requires two people!

2.4 Informal safety measures

 Keep the assembly/operating manual in the place where the workstation frame is used at

all times.

 Make sure that all safety information on the table (see Section 2.2, Symbols used on the

workstation frame) is legible, replacing the same if necessary.

2.5 Note for those assembling the workstation

 The workstation must be assembled/worked on by persons over the age of 16.

 The persons referred to above must have read and understood the assembly/operating

manual.

2.6 Transport and assembly

 The workstation frame must be moved by two persons only, and in such cases must be

retracted.

 Do not drag or pull the workstation frame over the floor.

 Assemble the workstation frame with the supplied tools only. They are the only tools

which ensure that the screws can be tightened to the correct torque.

This symbol indicates an immediate threatening situation for any person’s life

or health. Failure to adhere to such information may have serious consequences

for health, or could even result in life-threatening injury or death.

This symbol indicates important information. Failure to adhere to such infor-

mation could lead to damage to the workstation.



Do not place objects or parts of the body under the workstation frame or be-

tween the cross members. This could cause serious injury.

Do not exceed the maximum permitted load on the workstation frame. Over-

loading could lead to breakage and serious injury as a consequence.

2.7 Use of the workstation frame

 Do not allow children to use the workstation frame unsupervised. Children may be un-

aware of the dangers presented by the workstation frame. They would be in serious

danger of injuring themselves, possibly even with fatal consequences. Further adjust-

ment must then be impossible as a safeguard against use by children.

 The workstation frame must only be used in appropriate areas.

 Do not use the workstation frame on an uneven surface. In such conditions it will not

be steady.

 Never exceed the maximum load on the workstation frame

2.8 Specific dangers

 When adjusting the height of the frame there is danger of injury. Make sure that there

is no-one else in the immediate surroundings of the frame.

 When assembling the workstation frame, make sure there is ample space to avoid colli-

sions (i.e. inclination of roof, fixed objects, filing cabinets, waste-paper bins etc.) in all

imaginable directions.

 Make sure there is ample space to avoid collisions if there are objects on the work sur-

face such as computers or computer peripherals.

 Make sure there is clearance of at least 25 mm from all other furniture, all around the

workstation frame.

2.9 In an emergency

 Stop using the workstation frame at once if you notice anything unusual (strange

sounds etc.).

 Have the workstation frame repaired by specialists. Refrain from using the workstation

frame until it has been successfully repaired.

2.10 Maintenance and upkeep

 The workstation frame and its components are low-maintenance items and need no

special regular maintenance.

 Do not perform any repairs on the work surface or other components yourself.

 Do not alter the construction of the work surface or its frame.

 Any faulty components removed must be replaced with new, original components

from the manufacturer. Use only original replacement parts made by the manufacturer.

Have any such work carried out by a specialist, making reference to this Assembly/

operating manual.

2.11 Cleaning

 Dust the workstation frame once a week with a dry cloth.

 Clean the workstation frame with a damp cloth and a weak solution of cleaner once a

fortnight.

2.12 Persistent risks

This workstation frame has been built to the state of the art and to recognized safety regula-

tions. Nonetheless, its use may constitute a risk to the health and safety of users or third par-

ties, damage to the workstation frame or to other items. The workstation frame must be used

only:

 for the purpose for which it was intended.

 if it is completely safe so to do.

3 Assembly

3.1 Checking the items supplied

 Carefully open the cardboard packaging.

 In doing so, do not use any long knife blades. They may damage the components in-

side.

 Check the parts supplied against the list in Section 1.4 Items supplied.

 Do not attempt to assemble the workstation frame if there is any damage or if there are

any incorrect components.

3.2 Packaging

 Remove the packaging. Treat as household waste/paper.

 Observe national legislation.

3.3 Tightening torques for screws used

 Assemble the workstation frame with the tools supplied only.

3.4 Assembly of the workstation

3.4.1 Pre-assembly of the Crossbar

Assemble the following components:

Before attempting assembly, read the safety information in Section 2.

Indicative:

Frame set-up Width/size tabletop

1,1 m 120 cm

1,3 m 140 cm

1,5 m 160 cm

1,7 m 180 cm

# Part name Qty

13 Straight bottom crossbar 1

08 Allen key M3 1

12.3 Set screw M6x6 12

14 90 degree bottom crossbar 1

15 Straight top crossbar 1

16 90 degree top crossbar 1

 Twist the set screws in the threaded holes.

 Do not yet tighten the set screws!

 Tighten the set screws only after assembling the components in step 3.4.9 Adjustment

of the frame width, page 19.

3.4.2 Mounting the Feet

Assemble the following components:

# Part name Qty

02 Foot 2

03 Centre foot 1

10 Foot adjuster 6

12.2 Bolt M6x25 12

12.8 Washer M6 12

08 Spanner M10 1

01 Leg 3

Photo 1

 Twist 2 foot adjusters into the bottom of each foot.

Photo 2 & 3

 Turn the pre-assembled legs up-side-down (with 2 persons).

  Secure the pre-assembled legs against falling over.

 Position the foot, like photo 3, in relation to the crossbar

 Connect each foot to a leg with 4 bolts and 4 washers.

 Tighten the 12 bolts with the spanner M10.

 Turn the legs back on its foot.

2

1

3 !

Otros manuales para Aluforce Pro 140 M

Tabla de contenidos

Idiomas:

Otros manuales de Rack y soporte de Actiforce

Actiforce

Actiforce STEELFORCE PRO SLS SERIES Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario