ACTi ACM-5811 series Manual de usuario

IP CCD D/N PoE Box Camera

ACM-5811 series

Ver. 120312

Quick Installation Guide

0-1

0Getting Started

1.1 PACKAGE CONTENTS

ACM-5811

Product CD Terminal Blocks for Power & DI/O

Warranty Card Accessory

0-1

1.2 PHYSICAL DESCRIPTION

1. DC Iris

DC Iris Lens Control Port

2. Analog Video Output

The IP CCD D/N PoE Box Camera supports one channel analog

video output.

3. Ethernet Port

The IP CCD D/N PoE Box Camera connects to the Ethernet via a

standard RJ45 connector. This camera can automatically detect

the best network speed when connected to other

auto-negotiation(NWAY) supported devices.

(10Base-T/100Base-TX Ethernet).

4. Reset Button

Step 1: Switch off IP device by disconnecting the power cable

0-2

Step 2: Press and continue to hold the Reset Button with a

pointed object. Reconnect the power cable while still holding the

reset button.

Step 3: Keep the reset button depressed for at least 6 seconds

before releasing it. The unit will then start up with factory default

settings.

5. The I/O Terminal Connector

Used in applications like motion detection, event triggering, time

lapse recording, alarm notifications, etc., the I/O terminal

connector provides the interface to:

•1 transistor output - For connecting external devices such as

relays and LEDs. Connected devices can be activated by Output

buttons on the Live View page or by an Event Type. The output

will show as active (in Event Configuration > Port Status) if the

alarm device is activated.

•1 digital input - An alarm input for connecting devices that can toggle

between an open and closed circuit, for example: PIRs,

door/window contacts, glass break detectors, etc. When a signal is

received, the device state changes and the input becomes active

(shown under Event Configuration > Port Status).

•Auxiliary power and GND

Pin 1

GND

Ground

Description

Pin 2

Auxiliary DC

Power input

(not to power

this camera)

Electrically connected in parallel with the con-

nector for the power supply, this pin provides an

auxiliary connector for mains power to the unit.

This pin can also be used to power auxiliary

equipment, with a maximum current of 100mA.

Voltage: 12V DC,

Max: 1.2W

Pin 3

Digital Input

Connect to GND to activate, or leave floating (or

unconnected) to deactivate.

Must not be exposed to

voltages greater than 30V

DC.

Pin 4

Transistor

Output

Uses an open-collector NPN transistor with the

emitter connected to the GND pin. If used with an

external relay, a diode must be connected in

parallel with the load, for protection against

Max load = <100mA

Max voltage = 24V DC

(to the transistor)

0-3

transient voltages.

The I/O terminal pins are numbered left to right, as shown below.

Connect input/output devices to the camera as follows:

1. Attach the cables for the device securely to the supplied green

connector block.

2. Once the cables are connected, push the connector block into the

terminal connector (also green) on the camera.

FUSE 1A

NPN

DC TO DC

3.3V

DC POWER

GND 1

CONVERTER

EARTH GND

RELAY

DIODE

DEVICE

POWER INPUT

CAMERA

6. Power Input

Connect the power adaptor here if your power input is DC12V.

7. Audio Input / Output

The IP device supports audio input and output with earphone jack

0-4

0-1

1.3 BASIC CONNECTIONS

Follow the procedures below to connect the IP device to the respective

apparatuses.

1. Connect an analog monitor to IP device video out (BNC Connector)

2. Connect the power adaptor to IP device

3. Connect IP CCD D/N PoE Box Camera’s ethernet port to an Ethernet

(RJ45 connectors). If your IP CCD D/N PoE Box Camera supports Power

Over Ethernet (PoE), you may connect it directly to a PoE supported

switch, a PoE injector connected to a switch or other Power Source

Equipments(PSE)

4. Connect a PC to the Ethernet hub (RJ45 connectors)

NOTE: For more detailed explanations, we provide a support

package that clarifies PoE related concepts for you. Please visit our

web site and download the support document TS-00040.

1-2

1Quick Tour

This section guides you with a quick tour on this IP device.

2.1 Configure this IP Device

2.1.1 Make sure network environment

Default IP of this IP device is 192.168.0.100. Please make sure this IP device and

your PC are on the same network segment before running the installation.

Please set the settings as below.

IP address: 192.168. 0.xxx

Subnet mask: 255.255.255. 0

(NOTE: xxx should be a number

from 1 to 254 except 100, which is

used by the IP device. Please also

make sure that no two equipments

use the same IP address in the

same network..)

Tabla de contenidos

Otros manuales de Cámara IP de ACTi

ACTi

ACTi CAM-5100H Manual de usuario

ACTi

ACTi TCM-56x1 series Manual de usuario

ACTi

ACTi ACM-8511 Manual de usuario

ACTi

ACTi TCM-5311 Manual de usuario

ACTi

ACTi ACM-1430 series Instrucciones de uso

ACTi

ACTi KCM-3211 Manual de usuario

ACTi

ACTi B21 Manual de usuario

ACTi

ACTi Indoor Dome Series E610 Manual de usuario

ACTi

ACTi ACM-4201 Manual de usuario

ACTi

ACTi CAM-5100M Manual de usuario

ACTi

ACTi TCM-4301 Manual de usuario

ACTi

ACTi ACM-4000 Instrucciones de uso

ACTi

ACTi ACM-4200 series Manual de usuario

ACTi

ACTi ACM-4100 series Manual de usuario

ACTi

ACTi CAM-5120 Manual de usuario

ACTi

ACTi ACM-5801 Instrucciones de uso

ACTi

ACTi KCM-7911 Instrucciones de uso

ACTi

ACTi ACM-1310 series Manual de usuario

ACTi

ACTi CAM-5100M Manual de usuario

ACTi

ACTi CAM-5100 Manual del propietario

ACTi

ACTi TCM-4101 Instrucciones de uso

ACTi

ACTi TCM-5611 Series Manual de usuario

ACTi

ACTi ACM-3701E Manual de usuario

ACTi

ACTi CAM-6200 Manual

Manuales populares de Cámara IP de otras marcas

FLIR

FLIR Exx series Manual de usuario

Avigilon

Avigilon H4A-BO1-IR Manual de usuario

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manual de usuario

ShareTech

ShareTech AV1 Manual de usuario

Ezviz

Ezviz C6C Manual de usuario

Melchioni

Melchioni UCAM 2015 Manual de usuario

Geutebruck

Geutebruck G-Cam/ESD-4630 Manual de usuario

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manual de usuario

Mitel

Mitel 6800i Series Manual de servicio

Vitek

Vitek VTC-IR403-212NP Manual de usuario

THOMSON

THOMSON DSC - 323W Manual de usuario

AVer

AVer FB2027 Manual de usuario

ENFORCER

ENFORCER EV-T5105-N2SQ Manual de usuario

Wansview

Wansview NC543 Manual de usuario

Eneo

Eneo MCB-64A0003M0A Manual de usuario

deView electronics

deView electronics CBDNI36F Manual de usuario

Swann

Swann SwannEye Manual de usuario

LevelOne

LevelOne IP CamSecure Manual de usuario