ActForNet LEGUANG N800 Manual de usuario

LEGUANG N800 Wireless Router

Configuration Guide

ActForNet Technologies Inc.

February 2014

LEGUANG N800 Configuration Guide

Contents

1. What is included................................................................................................................................. 3

2. Installation Guide................................................................................................................................ 3

2.1 How to connect........................................................................................................................... 3

2.2 How to reset................................................................................................................................ 4

2.3 How to configure your PC to set up the bridge...................................................................... 4

2.4 Login to the wireless router....................................................................................................... 5

3. Wireless Router Configuration......................................................................................................... 6

3.1 Wireless Router Operating Modes .......................................................................................... 6

3.2 Gateway Mode configuration.................................................................................................... 8

3.3 Bridge mode configuration......................................................................................................10

3.4 Wireless ISP mode................................................................................................................... 13

LEGUANG N800 Configuration Guide

1. What is included

2. Installation Guide

2.1 How to connect

N800 comes with 2 network ports, one of which (beside the power supply plug) is intended to

connect local PC or switches and the other is intended to connect service provider to upper level

router. N800 can be powered using the DC power supply shipped with the box or using Power

over Ethernet (PoE) through LAN port. Using power supply is very straightforward. Just plug the

jack of the power supply into the power outlet on the wireless router. When you install N800

outdoor and there is no power outlet around, PoE is a good solution. The black adapter is PoE

power supply. It comes with 2 ports: POE and LAN. LAN is used to connect the PC and POE is

used to connect to the LAN port of N800.

LEGUANG N800 Configuration Guide

2.2 How to reset

In some cases, you may need to factory reset the system. For example, you forget your

password. After the system has boot up which takes about 1 minute, press the RESET button

which is located between the power supply plug and LAN port(see diagram above) for around 15

seconds before release it, the system will be reset after reboot with default configuration.

2.3 How to configure your PC for initial setup

The default IP address of the wireless router LAN port is 192.168.1.1. Since DHCP server on LAN

port is enabled by default. You can simply enable DHCP on the PC connecting to the LAN port of

the wireless router and the PC will get IP address automatically.

LEGUANG N800 Configuration Guide

2.4 Login to the wireless router

The factory default IP address: 192.168.1.1

Default username: admin

Default password: admin

Open your browser and type the default IP into the address field, and enter the default user

credential as prompted, you should be able access the admin GUI of the wireless router.

LEGUANG N800 Configuration Guide

3. Wireless Router Configuration

3.1 Wireless Router Operating Modes

LEGUANG N800 supports three operation modes:

Gateway Mode: In this mode, the device works as a router, connecting to Internet with

WAN port via ADSL/Cable Modem. Local PCs are connected to the router with LAN port

or WiFi. Network Address Translation (NAT) is enabled. Local PCs share the same IP to ISP

through WAN port. WAN port supports PPPOE, DHCP client or static IP. DHCP server on

LAN port is enabled by default to assign IP address to local PCs. With outdoor high gain

antenna, N800 can also connect the remote network together to share the Internet

LEGUANG N800 Configuration Guide

connection. It is a very good solution for suburbs or rural area to access Internet. This is

the default mode of the equipment.

Bridge Mode: In this mode, all Ethernet ports and wireless interface are bridged

together so both network ports can be used to connect local PC. NAT function is

disabled. All the WAN related function and firewall are not supported. DHCP server on

LAN port can be enabled as needed. The device is essentially used as an access pint (AP).

Wireless ISP: In this mode, the device works as a wireless client and access point at the

same time. It acts as a wireless client to connect to ISP. It also acts as an access point to

connect local PCs with WiFi. All Ethernet ports are bridged together so both network

ports can be used to connect local PC. The NAT is enabled and all local PCs share the

same IP address to access ISP. The difference between Wireless ISP mode and Gateway

mode is that Gateway mode uses wired connection while Wireless ISP mode wireless

connection to access the service provider.

LEGUANG N800 Configuration Guide

3.2 Gateway Mode configuration

1. Gateway mode is the default operating mode. If you are running a brand new system, you

don’t have to make any change to be in this mode. Otherwise you can switch to Gateway

mode on operation mode page as following:

2. Configure the LAN settings

In Gateway mode, wireless router can be used as a DHCP server to assign IP address to PCs

on local network, either wired or wireless. It is recommended to use the default setting and

enable DHCP to avoid IP address conflict.

3. Configure WAN settings

WAN is the port that connects to the service providers and it has to be configured to access

the Internet. Wireless router supports Dynamic IP, PPPoE, Static IP or PPTP. Pick the

appropriate the settings according to the service provider requirement. For most home

users, either PPPoE(ADSL) or dynamic IP (cable modem) should be used.

LEGUANG N800 Configuration Guide

4. Wireless settings

At a minimum, you need to configure the SSID(network name), region, authentication

scheme and the key.

After you click apply, the system will take a few seconds to make the new settings take

effect:

LEGUANG N800 Configuration Guide

In some cases, you may want to set up virtual access point to separate the wireless network.

N800 supports up to 2 virtual access points. Click “Virtual AP”, supply the SSID,

authentication scheme and key and then click “add”. After you click “Apply”, the system will

reboot with newly added virtual access points:

5. Now you should be able to see the wireless network you just configured from your PC or

tablet, smart phones, etc. Click the network and supply the password/key you just

configured to access the network.

3.3 Bridge Mode configuration

1. Switch to bridge mode

Since the default mode is not bridge mode, you need to manually change the operating

mode as following:

After you click “Apply”, the system will ask you to confirm whether to reboot the system to

make the change take effect.

Tabla de contenidos

Otros manuales de Enrutador inalámbrico de ActForNet

ActForNet

ActForNet LEGUANG N900 Manual de usuario

Manuales populares de Enrutador inalámbrico de otras marcas

Milesight

Milesight UG67 Manual de usuario

Airlogic

Airlogic AirSync Class 1 Manual del propietario

Samsung

Samsung WCH730B Manual de usuario

TELEFONICA

TELEFONICA USB Adapter Manual de usuario

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manual de usuario

Askey

Askey RAC2V1K Manual de usuario

Alloy

Alloy WLF2454AP-S Manual de usuario

TP-Link

TP-Link TL-WR542G Manual de usuario

NETGEAR

NETGEAR WNR2000v4 Manual de usuario

Hama

Hama 53120 Manual de usuario

Intellinet

Intellinet 524582 Manual de usuario

Asus

Asus RT-N10P Manual de usuario

D-Link

D-Link DIR-506L Manual de usuario

Sapido

Sapido GR297n Manual de usuario

Asus

Asus DSL-N55U Manual de usuario

AMTC

AMTC WR7502 Manual de usuario

Compaq

Compaq CP-2W - iPAQ Connection Point Manual de usuario

SMC Networks

SMC Networks WBR14-N2 FICHE Manual de usuario