Ace-Hi AH-2200 Instrucciones de instalación
The following is the safety guideline that you must read through and understand for
the use of AH-2200 non steam electric iron so that you can prevent from being injured or
the danger of the fire.
Safety Instruction For Using AH-2200 Non Steam Electric Iron
1. heck the electrical specification of this iron
before use. If it’s not the same voltage, it may
cause to an unexpected accident or the damage
to the product. In such case, the product can-
not be warranted.
2. In connecting the line cord of AH-2200 with
an electrical device, make sure that it is the
same electrical voltage. It is recommended to
connect directly with the outlet grounded.
3. Do not tie, pull or bend the line cord
unreasonably excessively, and never use the
damaged line cord or plug.
4. When the iron is dropped, and some parts are
broken or crashed, and if it does not work nor-
mally, do not try to fix it for yourself.
Just send it to our service center or to the
distributor who you purchased from.
5. Keep this item from the water and wet hands
when you plug it in or off, and make sure to
grab the plug. Never pull the line cord to
unplug it.
6. PAY SPE IAL ATTENTION TO THE
IRON WHILE IT’S HOT.
A. Do not leave the iron unattended.
B. Even after the use and the plug is off,
take good care of this iron until it gets
cool enough to be safe.
. When in use or not,
Place the iron always on the silicone iron
rest rightly.
Refer to the below chart for the proper temperature
settings of the iron;
How to Use
onnect the line cord, Turn On the Switch.
The indicating light is turned on and stays on until
it reaches to the set temperature. When the set tem-
perature is reached, the light goes off and it means
it’s ready to use.
If the clothes is made of mixed fabric, choose
the lower temperature setting.
For the delicate fabric, try it out on the inside of
the clothes to see if it’s okay. Improper selection of
the temperature may bring the result of being burnt
or shining on the fabric. We recommend, for this
case, to use the Teflon shoe.
While the iron is in use, the indicating light may
go on and off according to the inside temperature
of the iron. This is the normal phenomenon to
show that the iron is working properly.
Maintaining After Use
Turn Off the Switch and Plug It Off.
Wait Until the Iron Gets ool Before You Leave.
Make Sure Once Again That the Iron Is ool.
Do not Place the Iron on Vertical Stand.
Use Silicone Iron Rest When You Place the Iron.
Other Metallic Iron Rest May ause to Scratches.
Safety Warning Direction for Ironing
Nylon, Silk Setting 1 ~ 2, 100—140o
Wool Setting 3, 140—160o
otton Setting 4, 160—180o
Linen Setting 5, 180—210o (_+/- )
Fabric Type Temperature Settings
leaning the Bottom Base of the Iron
When the body is completely cooled off,
clean the base using the soft and wet cloth.
Do not use coarse materials such as scrubber
from a sponge gourd and the brushes.
Model: AH-2200
The Specification
For the Repair Service / the Technical Questions,
ontact Our ustomer Service Below;
Tel: 845-267-5170
Fax: 845-267-5171
E-Mail: sa[email protected]om
newacehico@yahoo.com
info@silverstar.co.kr
Website: www.acehico.com
www.silverstar.co.kr
This product is for the industrial / professional
use only. We’re not responsible for the damages
from the use at the improper locations where the
safety is extremely concerned such as home.
Temp. ontrol Range 210o +/- 10o
Iron Body Hard Anodized Aluminum
Base Size 209 * 115 (mm)
Weight 1.67 kg
Electrical Voltage 120V, 50/60 Hz
Electrical onsumption 1000 W
Parts Diagram & Description
A BASE ASS’Y (120V)
B THERMOSTAT SET
B-1 THERMOSTAT
B-2 THERMOSTAT KNOB
OVER
D THERMO SHIELD
E HADLE ASS'Y
F MAIN SWIT H SET
G POWER ORD(120V)
H SILI ONE IRON REST
Otros manuales de Hierro de Ace-Hi
