ABB SafeRing Manual de usuario

We reserve all rights in this document and in the information contained therein: Reproduction, use or disclosure to third

parties without express authority is strictly forbidden. © ABB Technology Ltd.

SafeRing / SafePlus

Retrofit of auxiliary switch S7 & S10 for position indication

of load break switch and earthing switch

C, F and SI modules

Installation instructions

www.abb.com

Edition

1.0 Document status

RELEASED Responsible

NODIS

Location Date Name

Language

EN/NO

Prepared NODIS 2008-12-09 BJGU/GUSO

Checked NODIS 2008-12-16 MARE

Approved NODIS 2008-12-16 OLGR

Title

SAFERING / SAFEPLUS

RETROFIT OF AUXILIARY

SWITCH S7 & S10

C, F AND SI

MODULES

ABB ABB Technology Ltd. Document No.

1VDD200010 Sheet No.

1/12

We reserve all rights in this document and in the information contained therein: Reproduction, use or disclosure to third

parties without express authority is strictly forbidden. © ABB Technology Ltd.

General Safety Instructions!

- Check that the installation, putting into service and

maintenance of this apparatus is carried out by qualified

personnel with knowledge of the apparatus to be installed. All

the procedures as laid out in this installation and service

instruction manual must be known.

- To perform the following installation requires a vocational

training (electrician, electrical engineer) and some years of

experience.

- Make sure the standard and legal prescriptions are adhered to

during the installation, putting into service and maintenance.

All procedures must be carried out in strict compliance to the

rules of good working practice and safety at the work site.

- Please read this instruction manual and plan the work before

starting the installation.

- Strictly follow the information given in this instruction manual.

- Pay special attention to the danger notes as indicated in this

manual by the following symbol:

- Check and ensure that the personnel operating the apparatus

have the instruction manual at hand, as well as the necessary

information for correct installation.

- Before starting the retrofit upgrade the switchgear must be de-

energized. Please de-energize the switchgear by operating the

switches to disconnected position.

- Check that all mechanism springs are discharged. If in doubt,

close and open the switch.

ABB ABB Technology Ltd. Edition

1.0 Document No.

1VDD200010 Sheet No.

2/12

We reserve all rights in this document and in the information contained therein: Reproduction, use or disclosure to third

parties without express authority is strictly forbidden. © ABB Technology Ltd.

Sikkerhetsinstruks!

- Sørg for at installasjon, idriftsettelse og vedlikehold er utført

av kvalifisert personell som har kjennskap til utstyret som blir

installert. Vedkommende må også kjenne til prosedyrer som

er beskrevet i dette installasjonsheftet.

- For å utføre følgende installasjon kreves yrkesfaglig erfaring

som elektriker, elektroingeniør eller liknende.

- Sørg for at sikkerheten rundt installasjonsarbeidet er ivaretatt

i henhold til nasjonale normer og forskrifter. Arbeidet utføres

av en fagperson.

- Les manualen nøye før arbeidet påbegynnes.

- Utfør installasjonen nøyaktig som beskrevet i denne

manualen.

- Vær spesielt nøye med å lese og følge anvisninger når det er

indikert med fare symbolet:

- Sørg for at betjeningspersonell har dette installasjonsheftet

og har fått nødvendig informasjon når de betjener det

installerte utstyret.

- Før installasjonen påbegynnes, sørg for at avgangen det skal

jobbes på er strømløs og at bryterne er utkoblet.

- Alle fjærer på mekanismene må være avspent. For å forsikre seg

om dette kan bryteren lukkes og åpnes.

ABB ABB Technology Ltd. Edition

1.0 Document No.

1VDD200010 Sheet No.

3/12

We reserve all rights in this document and in the information contained therein: Reproduction, use or disclosure to third

parties without express authority is strictly forbidden. © ABB Technology Ltd.

Installation procedure

The pictures and drawings are for a C module, but this document is also valid for F and Sl modules

Bilder og tegninger er av C-felt, men dette dokumentet er også gyldig for F- og Sl-felt

Used until May 2007

Brukt inntil mai 2007

Eksisting front covers

Dagens frontdeksler

1. Unscrew the fixing screw and remove the upper and lower front covers

Løsne festeskruen og fjern øvre og nedre frontdeksel

ABB ABB Technology Ltd. Edition

1.0 Document No.

1VDD200010 Sheet No.

4/12

We reserve all rights in this document and in the information contained therein: Reproduction, use or disclosure to third

parties without express authority is strictly forbidden. © ABB Technology Ltd.

2. Unscrew the bracket for capacitive voltage indication

Skru av braketten for kapasitiv spenningsindikering

*Depending on SafeRing / SafePlus production year, the position

indicator may be different compared to the drawing above. Please

refer to Appendix A, if your position indicator is different.

*Avhengig av når SafeRing / SafePlus anlegget er produsert, kan

stillingsindikeringen være forskjellig fra tegningen over. Hvis dette er

tilfelle, vennligst se Appendix A for eldre stillingsindikatorer.

ABB ABB Technology Ltd. Edition

1.0 Document No.

1VDD200010 Sheet No.

5/12

We reserve all rights in this document and in the information contained therein: Reproduction, use or disclosure to third

parties without express authority is strictly forbidden. © ABB Technology Ltd.

3. Snap on protection on the edges of the mechanism to avoid

damage of wires

Monter kantbeskyttelse på mekanismen for å unngå skade på

ledninger

4. Fix the bracket for the terminals marked X1 to the mechanism with

2 pieces of M6x10 screws

Fest braketten med rekkeklemmene merket X1 til mekanismen med

2 stk M6x10 skruer

ABB ABB Technology Ltd. Edition

1.0 Document No.

1VDD200010 Sheet No.

6/12

We reserve all rights in this document and in the information contained therein: Reproduction, use or disclosure to third

parties without express authority is strictly forbidden. © ABB Technology Ltd.

M4 x10

S10

5. Pull the position indicator maximum 2 mm out and fit the auxiliary switch

marked S7 and S10 behind the camshaft

Fix the auxiliary switch with 2 pieces of M4x10 screws

Dra ut stillingsindikatoren maksimalt 2 mm og vipp signalvenderen merket

S7 og S10 bak kamakselen

Monter signalvenderen med 2 stk M4x10 skruer

IMPORTANT!

Fix the wires to avoid any damages from moving parts

VIKTIG!

Fest alle ledninger slik at skader fra bevegelige deler unngås

ABB ABB Technology Ltd. Edition

1.0 Document No.

1VDD200010 Sheet No.

7/12

We reserve all rights in this document and in the information contained therein: Reproduction, use or disclosure to third

parties without express authority is strictly forbidden. © ABB Technology Ltd.

6. Fix the bracket for capacitive voltage indicator, which was removed

during step 2

Fest braketten for kapasitiv spenningsindikator som ble fjernet under

punkt 2

7. Re-place and fix the front covers

Sett tilbake og fest frontdekslene

ABB ABB Technology Ltd. Edition

1.0 Document No.

1VDD200010 Sheet No.

8/12

We reserve all rights in this document and in the information contained therein: Reproduction, use or disclosure to third

parties without express authority is strictly forbidden. © ABB Technology Ltd.

APPENDIX A

Used until December 2002

Brukt inntil desember 2002

Used until May 2007

Brukt inntil mai 2007

3. Unscrew and remove the position indicator

Skru av stillingsindikatoren

4. Snap on protection on the edges of the mechanism to avoid

damage of wires

Monter kantbeskyttelse på mekanismen for å unngå

skade på ledninger

ABB ABB Technology Ltd. Edition

1.0 Document No.

1VDD200010 Sheet No.

9/12

We reserve all rights in this document and in the information contained therein: Reproduction, use or disclosure to third

parties without express authority is strictly forbidden. © ABB Technology Ltd.

M6x10

5. Fix the bracket for terminals marked X1 to the mechanism with

2 pieces of M6x10 screws

Fest braketten med rekkeklemmene merket X1 til mekanismen med

2 stk M6x10 skruer

ABB ABB Technology Ltd. Edition

1.0 Document No.

1VDD200010 Sheet No.

10/12

Otros manuales para SafeRing

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de ABB

ABB

ABB TL Series Manual de usuario

ABB

ABB TX series Manual de instrucciones

ABB

ABB OTM C Series Manual de usuario

ABB

ABB SACE Tmax XT2 Manual de usuario

ABB

ABB MS40/EX Manual de instrucciones

ABB

ABB 3299-22958 Manual de usuario

ABB

ABB OKL 25 Series Manual de usuario

ABB

ABB 3299A-A12100 Manual de usuario

ABB

ABB EDS500 Series Manual de usuario

ABB

ABB JSTD20 Manual de usuario

ABB

ABB Zenith ZTS T Series Manual de usuario

ABB

ABB i-bus KNX 6108/02-500 Manual de lista de piezas

ABB

ABB ATS022 Manual de usuario

ABB

ABB E232-230 Manual de usuario

ABB

ABB 6953 EB-101-500 Manual de usuario

ABB

ABB SACE Emax Guía

ABB

ABB FAP 1001 Manual de usuario

ABB

ABB SACE Tmax T5 1000V DC Manual de usuario

ABB

ABB NE820 Manual de usuario

ABB

ABB EDS500 Series Manual de usuario

ABB

ABB Sense 7 Series Manual de usuario

ABB

ABB 3299A-A02100 x Guía de configuración

ABB

ABB OTM_C_21D Manual de usuario

ABB

ABB ITS2.1 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario