ABB IRB 260 Manual de usuario

ABB Robotics

Product manual

IRB 260

Trace back information:

Workspace R13-1 version a6

Checked in 2013-03-31

Skribenta version 1184

Product manual

IRB 260

M2004

Document ID: 3HAC026048-001

Revision: E

The information in this manual is subject to change without notice and should not

be construed as a commitment by ABB. ABB assumes no responsibility for any errors

that may appear in this manual.

Except as may be expressly stated anywhere in this manual, nothing herein shall be

construed as any kind of guarantee or warranty by ABB for losses, damages to

persons or property, fitness for a specific purpose or the like.

In no event shall ABB be liable for incidental or consequential damages arising from

use of this manual and products described herein.

This manual and parts thereof must not be reproduced or copied without ABB's

written permission.

Additional copies of this manual may be obtained from ABB.

The original language for this publication is English. Any other languages that are

supplied have been translated from English.

ABB AB

Robotics Products

SE-721 68 Västerås

Sweden

Table of contents
9Overview of this manual ...................................................................................................................
12Product documentation, M2004 .......................................................................................................
14How to read the product manual ......................................................................................................
151 Safety
151.1 Introduction to safety information ......................................................................... 161.2 General safety information .................................................................................. 161.2.1 Introduction to general safety information .................................................... 171.2.2 Safety in the manipulator system ............................................................... 181.2.3 Safety risks ............................................................................................ 181.2.3.1 Safety risks during installation and service work on manipulators ......... 211.2.3.2 CAUTION - Hot parts may cause burns! ........................................... 221.2.3.3 Safety risks related to tools/work pieces .......................................... 231.2.3.4 Safety risks related to pneumatic/hydraulic systems .......................... 241.2.3.5 Safety risks during operational disturbances ..................................... 251.2.3.6 Risks associated with live electric parts ........................................... 271.2.4 Safety actions ......................................................................................... 271.2.4.1 Safety fence dimensions ............................................................... 281.2.4.2 Fire extinguishing ........................................................................ 291.2.4.3 Emergency release of the manipulator’s arm .................................... 301.2.4.4 Brake testing .............................................................................. 311.2.4.5 Risk of disabling function "Reduced speed 250 mm/s" ........................ 321.2.4.6 Safe use of the FlexPendant .......................................................... 331.2.4.7 Work inside the manipulator's working range ................................... 341.2.5 Safety stops ........................................................................................... 341.2.5.1 What is an emergency stop? .......................................................... 361.3 Safety related instructions .................................................................................. 361.3.1 Safety signals in the manual ...................................................................... 381.3.2 Safety symbols on manipulator labels ......................................................... 431.3.3 DANGER - Moving manipulators are potentially lethal! ................................... 441.3.4 DANGER - First test run may cause injury or damage! ................................... 451.3.5 DANGER - Make sure that the main power has been switched off! .................... 471.3.6 WARNING - The unit is sensitive to ESD! ..................................................... 491.3.7 WARNING - Safety risks during handling of batteries ..................................... 501.3.8 WARNING - Safety risks during work with gearbox lubricants (oil or grease) ......
532 Installation and commissioning
532.1 Introduction ...................................................................................................... 542.2 Unpacking ....................................................................................................... 542.2.1 Pre-installation procedure ......................................................................... 572.2.2 Working range ........................................................................................ 592.2.3 Risk of tipping/stability ............................................................................. 602.3 On-site installation ............................................................................................ 602.3.1 Lifting of robot ........................................................................................ 642.3.2 Manually releasing the brakes ................................................................... 662.3.3 Orienting and securing the robot ................................................................ 692.3.4 Fitting equipment on the robot and robot dimensions ..................................... 732.3.5 Loads .................................................................................................... 742.3.6 Load diagram ......................................................................................... 752.3.7 Installation of signal lamp (option) .............................................................. 772.4 Restricting the working range .............................................................................. 772.4.1 Introduction ............................................................................................ 782.4.2 Mechanically restricting the working range of axis 1 ...................................... 842.4.3 Installation of position switch, axis 1 ........................................................... 872.4.4 Mechanically restricting the working range of axis 2 ...................................... 902.4.5 Mechanically restricting the working range of axis 3 ......................................
3HAC026048-001 Revision: E 5
© Copyright 2006-2013 ABB. All rights reserved.
Table of contents

5 Electrical connections ........................................................................................ 922.5.1 Connectors on robot ................................................................................ 932.5.2 Robot cabling and connection points ..........................................................
Maintenance
1 Introduction ...................................................................................................... 963.2 Maintenance schedule ....................................................................................... 963.2.1 Specification of maintenance intervals ........................................................ 973.2.2 Maintenance schedule ............................................................................. 983.3 Inspection activities ........................................................................................... 983.3.1 Inspection of information labels ................................................................. 1003.4 Changing activities ............................................................................................ 1003.4.1 Type of lubrication in gearboxes ................................................................ 1023.4.2 Oil change, gearbox axis 6 (wrist unit) ......................................................... 1043.4.3 Replacement of SMB battery ..................................................................... 1083.5 Cleaning activities ............................................................................................. 1083.5.1 Cleaning, robot ......................................................................................
Repair
1 Introduction ...................................................................................................... 1124.2 General procedures ........................................................................................... 1124.2.1 Performing a leak-down test ..................................................................... 1134.2.2 Mounting instructions for bearings ............................................................. 1154.2.3 Mounting instructions for seals .................................................................. 1174.3 Complete robot ................................................................................................ 1174.3.1 Replacement of cable unit, axes 1-3 ........................................................... 1234.3.2 Replacement of cable unit, axis 6 ............................................................... 1284.4 Upper arm ....................................................................................................... 1284.4.1 Replacement of shaft and bearings, tilthouse ............................................... 1404.4.2 Replacement of turning disk ...................................................................... 1434.4.3 Replacement of complete upper arm ........................................................... 1504.4.4 Replacement of linkage - upper rod ............................................................ 1534.4.5 Replacing the linkage - lower rod ............................................................... 1574.4.6 Replacement of linkage - link ..................................................................... 1624.5 Lower arm ....................................................................................................... 1624.5.1 Replacement of complete lower arm ........................................................... 1664.5.2 Replacement of parallel bar ....................................................................... 1704.6 Frame and base ............................................................................................... 1704.6.1 Replacement of SMB unit ......................................................................... 1764.6.2 Replacement of brake release unit ............................................................. 1784.6.3 Replacement of parallel arm ...................................................................... 1824.7 Motors ............................................................................................................ 1824.7.1 Replacement of motor, axis 1 .................................................................... 1874.7.2 Replacement of motor, axis 2 .................................................................... 1924.7.3 Replacement of motor, axis 3 .................................................................... 1974.7.4 Replacement of motor, axis 6 .................................................................... 2004.8 Gearboxes ....................................................................................................... 2004.8.1 Replacement of gearbox, axis 1-3 ............................................................... 2034.8.2 Replacement of gearbox, axis 6 .................................................................
Calibration information
1 Introduction ..................................................................................................... 2085.2 Calibration methods ........................................................................................... 2095.3 Calibration scale and correct axis position ............................................................. 2105.4 Calibration movement directions for all axes .......................................................... 2115.5 Updating revolution counters ............................................................................... 2135.6 Checking the calibration position ..........................................................................
3HAC026048-001 Revision: E
© Copyright 2006-2013 ABB. All rights reserved.
Table of contents

2156 Decommissioning
2156.1 Environmental information ..................................................................................
2177 Reference information
2177.1 Introduction ...................................................................................................... 2187.2 Applicable safety standards ................................................................................ 2207.3 Unit conversion ................................................................................................. 2217.4 Screw joints .................................................................................................... 2247.5 Weight specifications ......................................................................................... 2257.6 Standard tools .................................................................................................. 2267.7 Special tools .................................................................................................... 2367.8 Lifting accessories and lifting instructions ..............................................................
2378 Spare part lists and exploded views
2378.1 Introduction ...................................................................................................... 2388.2 Spare parts - overview ....................................................................................... 2398.3 Spare parts - cover ............................................................................................ 2418.4 Spare parts - robot IRB 260 ................................................................................. 2448.5 Spare parts - axes 1-3 ........................................................................................ 2538.6 Spare parts - upper arm ...................................................................................... 2558.7 Spare parts - tilthouse ........................................................................................ 2578.8 Spare parts - linkage .......................................................................................... 2588.9 Spare parts - material set cabling axis 6 ................................................................
2619 Circuit diagram
2619.1 About circuit diagrams .......................................................................................
263Index
3HAC026048-001 Revision: E 7
© Copyright 2006-2013 ABB. All rights reserved.
Table of contents

This page is intentionally left blank

Overview of this manual

About this manual

This manual contains instructions for:

• mechanical and electrical installation of the robot

• maintenance of the robot

• mechanical and electrical repair of the robot.

The manual also contains reference information for all procedures detailed in the

manual.

Usage

This manual should be used during:

• installation, from lifting the robot to its work site and securing it to the

foundation, to making it ready for operation

• maintenance work

• repair work.

Who should read this manual?

This manual is intended for:

• installation personnel

• maintenance personnel

• repair personnel.

Prerequisites

A maintenance/repair/installation craftsman working with an ABB Robot must:

• be trained by ABB and have the required knowledge of mechanical and

electrical installation/repair/maintenance work.

Organization of chapters

The manual is organized in the following chapters:

ContentsChapter

Safety information that must be read through before performing

any installation or service work on robot. Contains general safety

aspects as well as more specific information about how to avoid

personal injuries and damage to the product.

Safety

Required information about lifting and installation of the robot.Installation and commis-

sioning

Step-by-step procedures that describe how to perform mainten-

ance of the robot. Based on a maintenance schedule that may

be used in the work of planning periodical maintenance.

Maintenance

Step-by-step procedures that describe how to perform repair

activities of the robot. Based on available spare parts.

Repair

Procedures that does not require specific calibration equipment.

General information about calibration.

Calibration information

Environmental information about the robot and its components.Decommissioning

Continues on next page

3HAC026048-001 Revision: E 9

Overview of this manual

ContentsChapter

Useful information when performing installation, maintenance

or repair work. Includes lists of necessary tools, additional

documents, safety standards, etc.

Reference information

Complete spare part list and complete list of robot components,

shown in the exploded views.

Spare parts and exploded

views

Reference to the circuit diagram for the robot.Circuit diagram

References

Procedures in this product manual contain references to the following manuals:

Document IDDocument name

3HAC025046-001Product specification - IRB 260

3HAC025611-001Circuit diagram IRB 260

3HAC021313-001Product manual - IRC5

3HAC16590-1Operating manual - IRC5 with FlexPendant

3HAC16578-1Operating manual - Calibration Pendulum

3HAC025709-001Operating manual - Service Information System

3HAC021395-001Application manual - Additional axes and stand alone controller

3HAC042927-001Technical reference manual - Lubrication in gearboxes

3HAC17076-1Technical reference manual - System parameters

3HAC030421-001Application manual - CalibWare Field 5.0

Revisions

DescriptionRevision

First edition-

Changes made in:

• Prerequisites in section Overview

• Oil change in section Maintenance

Content updated in chapter/section:

•Maintenance chapter, section Maintenance schedule : Interval for

replacement of battery pack changed.

• Section What is an emergency stop? added to chapter Safety

• The oil Shell Tivela S 150 in gearbox axis 6 has been replaced by

Kyodo Yushi TMO 150.

Content updated in chapter/section:

• Decommissioning chapter added.

• Circuit diagrams are not included in this document but delivered

as separate files. See Circuit diagram on page 261.

• List of standards updated, see Applicable safety standards on

page 218.

The chapter Safety updated with:

•Updated safety signal graphics for the levels Danger and Warning,

see Safety signals in the manual on page 36.

• New safety labels on the manipulators, see Safety symbols on

manipulator labels on page 38.

• Revised terminology: robot replaced with manipulator.

Continues on next page

10 3HAC026048-001 Revision: E

Overview of this manual

Continued

Otros manuales para IRB 260

Tabla de contenidos

Otros manuales de Robótica de ABB

ABB

ABB OmniCore C30 Manual de usuario

ABB

ABB IRB 6710 Manual de usuario

ABB

ABB IRB 6640 Foundry Prime Manual de usuario

ABB

ABB IRB 260 Manual de usuario

ABB

ABB 180 Comfort Manual de usuario

ABB

ABB SpotPack IRB 6620 Manual de usuario

ABB

ABB IRB 360 Manual de usuario

ABB

ABB IRB 5720 Manual de usuario

ABB

ABB M2000 Manual de usuario

ABB

ABB CRB 15000 Manual de usuario

ABB

ABB MultiMove Instrucciones de uso

ABB

ABB IRB 460 Series Manual de usuario

ABB

ABB IRB 1660 Manual de usuario

ABB

ABB IRB 390 Manual de usuario

ABB

ABB CRB 1100 Manual de usuario

ABB

ABB ESAB W82 Manual de uso y cuidado

ABB

ABB IRB 6660 Manual de usuario

ABB

ABB TSC 2013 Manual de usuario

ABB

ABB IRBT 2005 Manual de usuario

ABB

ABB IRB 7600 Series Manual de usuario

ABB

ABB Scalable I/O Instrucciones de uso

ABB

ABB IRB 7600 - 500/2.55 Manual de usuario

ABB

ABB IRB 4400 Manual de usuario

ABB

ABB DressPack IRB 6620 Manual de usuario

Manuales populares de Robótica de otras marcas

STEMCenter USA

STEMCenter USA Pi-Bot v2.00 Manual de usuario

SunFounder

SunFounder PiDog Manual de usuario

Universal Robots

Universal Robots UR5 Manual de usuario

Universal Robots

Universal Robots E Series Manual de usuario

YASKAWA

YASKAWA MOTOMAN-MPL80 II Manual de usuario

EFORT

EFORT ECR5 Manual de instrucciones

Epson

Epson C8 Series Manual de usuario

WowWee

WowWee ROBOQUAD Manual de usuario

Milvus Robotics

Milvus Robotics SEIT 100 Manual de usuario

RoboMaster

RoboMaster AI Robot 2020 Standard Version Manual de usuario

fischertechnik

fischertechnik Mini Bots Manual de usuario

YASKAWA

YASKAWA MA2010 Manual

Abicor Binzel

Abicor Binzel iCAT mini Manual de usuario

YASKAWA

YASKAWA Motoman DX200 Manual de usuario

pitsco

pitsco Tetrix Max Manual de usuario

ECOVACS

ECOVACS DEEBOT R95 Manual de usuario

Feng Yuan

Feng Yuan Interstellar Warrior Manual de usuario

SCHUNK

SCHUNK AGE-S-XYZ Instrucciones de uso