ABB 10D1475 Manual de usuario

INSTALLATION

INSTRUCTIONS

Magnetic Flowmeter

Models 10D1475/1476/1477

PN25001A

Trim:

1 1/4 in. from Top & Bottom

3 in. from Right Side

Finished Size = 5 1/2 x 8 1/2

Drill:

1/4 in. dia. hole 3/8 in. from

Top & 3/8 in. from Left edge

Stock:

67 lb. Salmon Cover (all pages)

Binding:

Staple left edge

GENERAL

This installation instruction literature serves as a guide for proper in-

stallation of the associated magnetic flowmeter. A more detailed de-

scription of installation procedures will be found in the Instruction

Bulletin provided for the particular magnetic flowmeter primary.

FIGURE 1. Representative Integral Magnetic Flowmeter

GENERAL

INSTALLATION INSTRUCTIONS

TIPS & TECHNIQUES

Mounting hardware (supplied by ABB) consists of: studs, nuts, gas-

kets and adapter(s).Check itemized packing list to be certain that all

items listed have been received.

FIGURE 2. Recommended Piping Diagram

TIPS &

TECHNIQUES

INSTALLATION INSTRUCTIONS

NOTE

Although a vertical installation of your meter is

best, a horizontal or sloping installation can be

very successful if the meter electrodes are ori-

ented in a horizontal plane. If either electrode is

positioned at the top, entrapped air may act as an

insulator, resulting in an unreliable measurement.

This tag highlights the installation techniques necessary for depend-

able service from your ABB Magnetic Flowmeter. By observing and

performing these operations, your meter warranty remains valid and

satisfactory performance is assured. Coverage of all recommenda-

tions given in this instruction is provided in detail within the Instruction

Manual which accompanies your meter.

METER GASKETS

Flanges must be

properly gasketed

Two gaskets are provided in the Installation Kit, as selected for the

particular application.

CONDUIT CONNECTIONS

Conduit seal fittings must be properly installed at the meter primary to

prevent condensate, that may be present in the conduit system, from

entering the customer connection box and degrading meter perform-

ance.

Conduit seals are also required to prevent the process fluid from en-

tering the electrical conduit system. This safety feature considers the

remote possibility of a primary seal failure within the flowmeter, in

which case, this secondary seal will prevent the process from enter-

ing the electrical conduit system in accordance with the National

Electrical Code (NEC) ANSI/NFPA 70, Article 501-5 (f) (3). A cable

seal and mating fittings are supplied with the meter for cables that in-

terconnect with a remotely mounted signal converter. When an inte-

grally mounted signal converter is supplied, cable seals and fittings

are provided only when the accidental submergence option has been

specified.

Proper assembly of the cable

seal and fittings is illustrated

in the adjacent diagram. If the

seal provided contains plugs

in the thru-holes, remove only

those plugs required to ac-

commodate necessary wiring.

The proper use of conduit and

seals provides physical pro-

tection for all external wiring,

makes the meter weatherproof

and provides added assur-

ance against undesireable

stray pick up on signal trans-

mission leads. FIGURE 3. Typical Conduit Seal

✔

TIPS &

TECHNIQUES

INSTALLATION INSTRUCTIONS

MOUNTING PROCEDURE

INSTALLATION OF 1/10 - 3/8 INCH METERS

•Align flange adapter on meter

body, as shown below.

•Install a gasket at meter inlet and

outlet, as applicable for meter

type. Observe flow direction arrow.

•Insert meter with (with gaskets)

between pipe flanges.

•Insert mounting studs through bolt

holes.

•Thread nuts on mounting studs

(finger tight).

•Press down on flange adapter to

force-spread studs, thereby cen-

tering meter in pipeline.

•Use proper torque and tightening

sequence (i.e. 1-3-2-4) to maintain

even pressure distribution as

shown in the figure to the right.

MOUNTING

PROCEDURE

FIGURE 4. Meter Mounting Diagram, 1/10 - 3/8 in. Sizes

ABB

3 - 10

(1/10 - 3/8)

NOTE: Meter shown is Model 10D1476/1477

INSTALLATION INSTRUCTIONS

INSTALLATION OF 1/2 - 4 INCH METERS

•Install a gasket at meter inlet and

outlet, as applicable for meter type.

•Insert meter (with gaskets) between

pipe flanges.

•Insert two lower mounting studs with

adaptor sleeves between pipe

flanges.

•Insert top two mounting studs and

sleeves (this will center the meter in

pipeline); install other mounting

studs, if required.

•Thread nuts on studs. Use proper

torque and tightening sequence (i.e.

1-5-3-7, 2-6-4-8) to maintain even

pressure distribution as shown in

the figure to the right.

MOUNTING

PROCEDURE

FIGURE 5. Meter Mounting Diagram, 1/2 - 4 in. Sizes

ADAPTER SLEEVES

INSTALLATION INSTRUCTIONS

GROUNDING PROCEDURE

ELECTRICALLY CONDUCTIVE PIPELINE

(Liquid in Electrical Contact With Pipeline)

FOR OPTIMUM SYSTEM PERFORMANCE

the flowmeter body and electrically conductive pip-

ing must be connected to a good earth ground.

•Although grounding

straps are not actually

packed within the In-

stallation Kit, they are

attached to the Mag-

netic Flowmeter.

Proper use of these

straps is mandatory for

satisfactory operation.

Perform the applicable

grounding procedure.

•Two bonding straps are

supplied with the meter

for connection to the

upstream and down-

stream pipe flanges.

Flanges must be drilled

and tapped.

( Refer to FIGURE 6 )

•Customer must supply

and install bonding

strap (e.g., 1/2" copper

braid) from meter body

to an external earth

ground.

NOTE

Refer to appropriate Instruction Bulletin supplied

by ABB for electrical interconnection diagram(s).

GROUNDING

PROCEDURE

FIGURE 6. Grounding Procedure,

Conductive Pipeline

GROUNDING STRAPS

ABB

INSTALLATION INSTRUCTIONS

ELECTRICALLY NON-CONDUCTIVE PIPELINE

(Liquid NOT in Electrical Contact With Pipeline)

SYSTEMS USING INSULATED PIPE INCLUDE:

Ceramic lined cast iron pipe

Plastic pipe*

Concrete pipe*

Teflon lined pipe

* Model 10D1477 may not be installed in these types of pipelines. Consult instruction manual for details.

FOR OPTIMUM SYSTEM PERFORMANCE

the flowmeter body and electrically conductive pip-

ing must be connected to a good earth ground.

•Install grounding ring

between pipe flange

and meter (one up-

stream and one

downstream).

( Refer to FIGURE 7 )

•Two ground straps

are supplied with the

meter for connection

to the upstream and

downstream ground-

ing rings.

•Customer must sup-

ply and in-stall

ground strap (e.g.,

1/2" copper braid)

from meter ground-

ing stud to an exter-

nal earth ground.

•Refer to Figure 8 for

optional grounding

ring dimensions.

NOTE

Refer to applicable Instruction Bulletin supplied by

ABB for electrical interconnection diagram(s).

GROUNDING

PROCEDURE

FIGURE 7. Grounding Procedure,

Non-Conductive Pipeline

ABB

INSTALLATION INSTRUCTIONS

OPTIONAL GROUNDING RINGS

•The grounding ring

material must be con-

ductive and not sub-

ject to chemical

reaction with the me-

tered fluid.

•Grounding rings are

available from ABB (2

required).

( Refer to FIGURE 8 )

FIGURE 8. Outline Dimensions of

Accessory Grounding Rings

GROUNDING

PROCEDURE

INSTALLATION INSTRUCTIONS

The Company’s policy is one of continuous product improvement and the

right is reserved to modify the information contained herein without notice.

ABB Inc.

125 East County Line Road

Warminster, PA 18974 USA

Tel. 215-674-6000

FAX: 215-674-7183

ABB Instrumentation Ltd

Howard Road, St. Neots

Cambs. England, PE19 3EU

Tel. +44 (0) 1480-475-321

FAX: +44 (0) 1480-217-948

ABB Instrumentation S.p.A

Via Sempione 243

20016 Pero (Milano) Italy

Tel: +39 (02) 33928 1

Fax: +39 (02) 33928 240

ABB Automation Products GmbH

Industriestr. 28

D-65760 Eschborn Germany

Tel: +49 (0) 6196 800 0

Fax: +49 (0) 6196 800 1849

PN25001A

Otros manuales para 10D1475

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de ABB

ABB

ABB Totalflow uFLO 6213 Guía del usuario

ABB

ABB EXGP Manual de usuario

ABB

ABB PFEA 111 Manual de usuario

ABB

ABB NGC Series Manual de usuario

ABB

ABB M4M 30 Manual de usuario

ABB

ABB ACF-NT Manual de usuario

ABB

ABB NETA-21 Manual de usuario

ABB

ABB MR Series Manual

ABB

ABB Endura AZ20 series Manual de usuario

ABB

ABB PFEA 113 Manual de usuario

ABB

ABB i-bus EIB Delta-Meter Manual de usuario

ABB

ABB VortexMaster FSV430 Instrucciones de instalación

ABB

ABB MagMaster Manual de usuario

ABB

ABB NETA-21 Manual de instalación

ABB

ABB CM-ENS Manual de usuario

ABB

ABB COPA-XM 3000 Series Manual de usuario

ABB

ABB CoriolisMaster FCB330 Manual de instalación y operación

ABB

ABB TRIO-WIRL ST4000 Manual de usuario

ABB

ABB TTF200 Manual de usuario

ABB

ABB FEX300 Instrucciones de operación

ABB

ABB 2112U-101-500 Manual de usuario

ABB

ABB VLMD-1-2 Manual de usuario

ABB

ABB LS4000 Manual de usuario

ABB

ABB AquaProbe 2 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario