ABB ACS880 Series Manual de usuario

—

ABB INDUSTRIAL DRIVES

ACS880 liquid-cooled multidrive cabinets

Mechanical installation instructions

ACS880 liquid-cooled multidrive

cabinets

Mechanical installation instructions

Table of contents

1. Mechanical installation

EFFECTIVE: 2019-06-30

Table of contents

1 Mechanical installation

7Contents of this chapter ..........................................................................

7Examining the installation site ..................................................................

7Necessary tools ...................................................................................

8Checking the delivery ............................................................................

9Moving and unpacking the drive ................................................................

9Moving the drive in its packaging ...........................................................

9Lifting the crate with a forklift .............................................................

10Lifting the crate with a crane .............................................................

11Moving the crate with a forklift ...........................................................

11Removing the transport package ...........................................................

12Moving the unpacked drive cabinet .........................................................

12Lifting the cabinet with a crane ..........................................................

13Moving the cabinet on rollers ............................................................

13Moving the cabinet on its back ...........................................................

14Final placement of the cabinet ...........................................................

15Fastening the cabinet to the floor and wall or roof ...........................................

15General rules ...................................................................................

16Fastening the cabinet (non-marine units) ..................................................

16Alternative 1 – Clamping ..................................................................

17Alternative 2 – Using the holes inside the cabinet ....................................

18Fastening the cabinet (marine units) .......................................................

19Joining cabinet sections together ...............................................................

22Miscellaneous .....................................................................................

22Cable duct in the floor below the cabinet ..................................................

22Arc welding .....................................................................................

Further information

Table of contents 5

Mechanical installation

Contents of this chapter

This chapter describes the mechanical installation procedure of the drive.

Examining the installation site

Examine the installation site:

• The installation site is sufficiently ventilated or cooled to remove heat from the drive.

See the technical data.

• The ambient conditions of the drive meet the specifications. See the technical data.

• There is enough free space above the drive to enable cooling, maintenance, and

operation of the pressure relief (if present).

• The floor that the drive cabinet is installed on is of non-flammable material, as smooth

as possible, and strong enough to support the weight of the unit. Check the floor flatness

with a spirit level. The maximum allowed deviation from the surface level is 5 mm in

every 3 meters. Level the installation site, if necessary, as the cabinet is not equipped

with adjustable feet.

Necessary tools

The tools required for moving the unit to its final position, fastening it to the floor and wall

and tightening the connections are listed below:

• crane, fork-lift or pallet truck (check load capacity!), slate/spud bar, jack and rollers

• Pozidriv and Torx screwdrivers

• torque wrench

• set of wrenches or sockets.

Mechanical installation 7

Checking the delivery

The drive delivery contains:

• drive cabinet line-up

• optional modules (if ordered) installed onto the control unit(s) at the factory

• appropriate drive and optional module manuals

• delivery documents.

Check that there are no signs of damage. Before attempting installation and operation,

check the information on the type designation labels of the drive to verify that the delivery

is of the correct type.

8 Mechanical installation

Moving and unpacking the drive

Move the drive in its original packaging to the installation site as shown below to avoid

damaging the cabinet surfaces and door devices. When you are using a pallet truck, check

its load capacity before you move the drive.

The drive cabinet is to be moved in the upright position.

The center of gravity of the cabinet is high. Be therefore careful when moving the unit. Avoid

tilting.

￭Moving the drive in its packaging

Lifting the crate with a forklift



Mechanical installation 9

Lifting the crate with a crane

max 20

Lifting pointa

Optimal position for the lifting sling: as close to the traverse board

as possible

10 Mechanical installation

Otros manuales para ACS880 Series

Tabla de contenidos

Otros manuales de Accionamiento de CC de ABB

ABB

ABB ACH550-01 Manual de usuario

ABB

ABB ACS880-31 Manual de usuario

ABB

ABB ACQ580-01 Series Manual de instalación

ABB

ABB ACH550 series Manual de usuario

ABB

ABB ACS480 Instrucciones de funcionamiento

ABB

ABB ACS580-01 drives Manual de instalación

ABB

ABB ACQ580-P Series Manual de usuario

ABB

ABB ACS580-01 drives Manual de instalación

ABB

ABB ACS260-04 Series Manual de usuario

ABB

ABB ACS880 Series Manual de usuario

ABB

ABB ACH580 Series Manual de usuario

ABB

ABB UNITROL 1010 Manual de usuario

ABB

ABB ACS480 Manual de usuario

ABB

ABB Johnson Controls AYK550-UH Manual de usuario

ABB

ABB DCS800 Manual de uso y cuidado

ABB

ABB ACS850 series Guía de solución de problemas

ABB

ABB ACH480 Manual de usuario

ABB

ABB ACS880-04 drive modules Guía del usuario

ABB

ABB ACS560 Manual de instalación

ABB

ABB ACH550-UH HVAC Manual de usuario

ABB

ABB ACS 600 Manual de usuario

ABB

ABB ACS880-04F-504A-3 Manual de usuario

ABB

ABB ACS550-CC Manual de usuario

ABB

ABB DMP Series Manual

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

Danfoss

Danfoss VLT 2800 Series Hoja de especificaciones

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

GE D20A6 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

SOMFY

SOMFY JR RU 30 Manual de usuario

Beckhoff

Beckhoff AX8911 Manual del operador

Minarik

Minarik MM300 Series Manual de usuario