ABB ACS560 Manual de instalación

—

ABB GENERAL PURPOSE DRIVES

ACS560 standard control program

Quick installation and start-up guide

ENEnglish . . . . . . . 3

 ........ 171

3AXD50000042620 Rev J MUL

EFFECTIVE: 2022-08-16

EN - Quick installation and

start-up guide

This guide instructs how to install and start-up the ACS560 drive of all frame sizes

(R0...R8). For complete information, see the drive

ACS560 standard control program

firmware manual

(3AXD50000044997[English]) and

ACS560 drives (0.75 to 160

kW, 1.0 to 215 hp) hardware manual

(3AXD50000044998[English]).

General considerations

￭Obey the safety instructions

WARNING! Obey these instructions. If you ignore them, injury or death, or

damage to the equipment can occur.

•If you are not a qualified electrician, do not do electrical installation work.

• Do not work on the drive, motor cable or motor when main power is

applied. If the drive is already connected to the input power, wait for 5

minutes after disconnecting the input power.

• Do not work on the control cables when power is applied to the drive or

to the external control circuits.

• Use the lifting eyes of the drive when you lift the drive. Do not tilt the

drive. The drive is heavy and its center of gravity is high. An overturning

drive can cause physical injury.

• Make sure that debris from borings and grindings does not enter the

drive when installing.

• Make sure that the floor below the drive and the wall where the drive is

installed are non-flammable.

￭Reform the capacitors

Reform the capacitors if the drive is stored for a year or more.

The manufacturing date is on the type designation label which is attached to the

drive. The serial number format MYYWWRXXXX represents the month, year and

the week.

YY: 13, 14, 15, … for 2013, 2014, 2015, …

WW: 01, 02, 03, … for week 1, week 2, week 3, …

EN - Quick installation and start-up guide 3

For information on reforming the capacitors, see

Converter module capacitor

reforming instructions

(3BFE64059629 [English]).

￭Select the power cables

Size the power cables according to local regulations to carry the nominal current

given on the type designation label of your drive. See Ratings (page 127).

￭Ensure the cooling

The maximum ambient temperature without derating is:

• 50 °C (+122 °F) for R0...R2 frames

• 40 °C (+104 °F) for R3...R8 frames

No condensation or frost is allowed. For more information on the ambient

temperature, see the hardware manual.

￭Protect the drive and input power cable

If you use gG fuses, make sure that the operating time of the fuse is below 0.5

seconds. Follow the local regulations.

4 EN - Quick installation and start-up guide

Install the drive

You can install the drive

• to a DIN installation rail with integrated lock. This method applies to frames

R0...R2 only.

• with screws to a suitable surface (wall or assembly plate). This method applies

to all frames R0...R8.

￭Required tools for installing the drive

• A drill and suitable drill bits.

• Screwdriver (Flat head, Phillips head, and Torx)

• wrench with suitable bits and sizes (appropriate for the installation hardware

used). See the required screw sizes in below installation instructions

• A tape measure and spirit level.

• Personal protective equipment.

￭Installing a drive to DIN installation rail (frames R0...R2 only)

1. On the top center of the drive move the locking part to the left.

2. Push and hold the locking button down.

3. Put the top tabs on the drive onto the top edge of the DIN rail.

4. Put the drive against the bottom edge of the DIN installation rail.

5. Release the locking button.

6. Move the locking part to the right.

7. Make sure the drive is installed correctly.

EN - Quick installation and start-up guide 5

￭Removing drive from the DIN installation rail (frames R0...R2 only)

To remove the drive, open the locking part using a flat-head screwdriver.

￭Installing a drive with screws (frames R0...R8)

All drives of frames R0...R8 can be installed on a wall with screws. See the required

screw sizes in below mounting dimensions table. See also Dimensions, weights

and free space requirements (page 132)

WARNING!

The drive module (frames R6...R8) is heavy (45 to 70 kg). Consider the

following:

• Use a suitable lifting device.

• Do not lift the module manually.

• Make sure that the wall and the fixing devices can carry the weight. See

data in the table below.

1. Mark the mounting hole locations using the mounting template included in

the package.

Mounting dimensionsMounting template

R8R7R6R5R4R3R2R1R0Frames

M8M6M5Screws

(mm)

658583531581619473191a

701623571612-b

2632452131601487550

-75d

20075e

70.055.045.028.023.014.867.544.574.47Weight

(kg)

2. Drill the mounting holes.

3. Tighten the screws into the mounting holes.

4. Position the drive onto the screws on the wall.

5. Tighten the mounting screws.

6 EN - Quick installation and start-up guide

234

See the example of mounting screws in frame R0

6. Frames R5...R8 only: Remove the front cover with fastening screws (6a), move

the cover to the top side (6b) and then up (6c).

7. Frames R5...R8 only: Attach the cable conduit box to the drive frame.

Note: Cable conduit box is optional and is not part of standard delivery.

8. Frames R5...R8 only: Tighten the box screws: two at the top and four at the

bottom.

EN - Quick installation and start-up guide 7

8 EN - Quick installation and start-up guide

Measuring the insulation resistance of the motor and motor

cable

Obey the safety instructions of the drive. If you ignore them, injury or

death, or damage to the equipment can occur. If you are not a qualified

electrical professional, do not do installation, commissioning or

maintenance work.

1. Follow the electrical safety precautions. See Electrical safety instructions in

the hardware manual.

2. Make sure that the motor cable is disconnected from the drive output terminals.

3. Measure the insulation resistance between each phase conductor and the

protective earth conductor. Use a measuring voltage of 1000 V DC. The

insulation resistance of an ABB motor must be more than 100 Mohm (reference

value at 25 °C [77 °F]). For the insulation resistance of other motors, refer to

the manufacturer’s instructions.

Note: Moisture inside the motor reduces the insulation resistance. If you think

that there is moisture in the motor, dry the motor and do the measurement

again.

1000 V DC,

>100 Mohm

U1-PE, V1-PE, W1-PE

ohm

W1 PE

EN - Quick installation and start-up guide 9

Connecting the power cables

￭Connection diagram

For alternatives, see hardware manual.1

Use a separate grounding PE cable (2a) or a cable with a separate PE conductor (2b)

if the conductivity of the shield does not meet the requirements for the PE conductor

(see hardware manual).

360° grounding is recommended if shielded cable is used. Ground the other end of the

input cable shield or PE conductor at the distribution board.

360° grounding is required.4

External brake resistor (for frames R4...R8 only).5

Use a separate grounding cable if the shield does not meet the requirements of IEC

61439-1 and there is no symmetrically constructed grounding conductor in the cable.

For more information, see hardware manual.

Note: If there is a symmetrically constructed grounding conductor on the motor cable in

addition to the conductive shield, connect the grounding conductor to the grounding ter-

minal at the drive and motor ends.

Do not use an asymmetrically constructed motor cable for motors above 30 kW. Earthing

at the motor increases bearing current and power consumption, damages the motor

bearing and even the motor.

10 EN - Quick installation and start-up guide

Otros manuales para ACS560

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accionamiento de CC de ABB

ABB

ABB ACS850-04 series Manual de usuario

ABB

ABB ACS860 Manual de uso y cuidado

ABB

ABB Q952 Manual de usuario

ABB

ABB ACS355 UL 4X Manual de usuario

ABB

ABB +Q950 Manual de usuario

ABB

ABB ACS880-34 Manual de usuario

ABB

ABB ACS550-02 Manual de usuario

ABB

ABB ACSM1-04 Series Manual de usuario

ABB

ABB ACS1000 Manual de usuario

ABB

ABB ACQ80-04 Series Manual de instalación

ABB

ABB ACS 800 Series Guía del usuario

ABB

ABB ACS880-04 drive modules Guía del usuario

ABB

ABB ACS880-37LC Manual de usuario

ABB

ABB Dodge HSCXT105 Manual de usuario

ABB

ABB ACS880-307LC Manual de usuario

ABB

ABB Johnson Controls AYK550-UH Manual de usuario

ABB

ABB ACS880-07 Manual de usuario

ABB

ABB ACS 800 Series Manual de operación y mantenimiento

ABB

ABB ACS480 Manual de instalación

ABB

ABB ACS 6000 Manual de usuario

ABB

ABB +Q951 Hoja de información del producto

ABB

ABB ACS510-01 Manual de usuario

ABB

ABB DCS880 series Manual de usuario

ABB

ABB ACS850-04 series Manual de usuario

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

Danfoss

Danfoss VLT 2800 Series Hoja de especificaciones

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

GE D20A6 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

SOMFY

SOMFY JR RU 30 Manual de usuario

Beckhoff

Beckhoff AX8911 Manual del operador

Minarik

Minarik MM300 Series Manual de usuario