3rd Power Dream Weaver 112 Manual de usuario
USERS GUIDE
1 1 2 C O M B O & H E A D
™
2
Your 3RD POWER Amplifier is a professional musical instrument amplifier. The information
contained herein is current at the time of publication. However, specifications are subject
to change without prior notice.
• READ THESE INSTRUCTIONS.
• KEEP THESE INSTRUCTIONS.
• HEED ALL WARNINGS.
• FOLLOW ALL INSTRUCTIONS.
• YOUR AMPLIFIER IS LOUD!
EXPOSURE TO HIGH SOUND VOLUMES MAY CAUSE PERMANENT HEARING DAMAGE ! Practice “safe
listening.”
• No user serviceable parts inside. Refer service to qualified personnel. Always unplug AC power be-
fore removing chassis.
• If you intend on operating this equipment outside of the USA: Always insure that unit is wired for
proper voltage. Make certain all connections and grounding conforms with local standards. Make
certain that you have obtained authorization to operate prior to connecting to power supply.
• WARNING: Vacuum tube amplifiers generate heat. To insure proper ventilation always make certain
there is at least four inches (100mm) of space behind the rear of the amplifier cabinet.
• Keep away from curtains or any flammable objects.
• WARNING: Do not block any ventilation openings on the rear or top of the amplifier. Do not impede
ventilation by placing objects on top of the amplifier which extend past the rear edge of its cabinet.
• WARNING: Do not expose the amplifier to rain, moisture, dripping or splashing water. Do not place
objects filled with liquids on or nearby the amplifier.
• WARNING: Always make certain proper load is connected before operating the amplifier. Failure to
do so could pose a shock hazard and may result in damage to the amplifier.
• Do not expose amplifier to direct sunlight or extremely high temperatures.
• Always insure that amplifier is properly grounded. Always unplug AC power cord before changing
fuse or any tubes. When replacing fuse, use only same type and rating.
• Avoid direct contact with heated tubes. Keep amplifier away from children.
• Be sure to connect to an AC power supply that meets the power supply specifications listed on the
rear of the unit. Remove the power plug from the AC mains socket if the unit is to be stored for an
extended period of time. If there is any danger of lightning occurring nearby, remove the power
plug from the wall socket in advance.
• To avoid damaging your speakers and other music equipment, turn off the power of all related
equipment before making the connections.
• Do not use excessive force in handling control buttons, switches and controls. Do not use solvents
such as benzene or paint thinner to clean the unit. Wipe off the exterior with soft cloth.
PRECAUTIONS & WARNINGS
3
™
Thank you for choosing 3RD POWER
as an integral component of your mu-
sical journey.
Music is a thrilling blend of tone, atti-
tude and technique. When the right
combination occurs, magic happens
and it’s experienced by everyone.
I’ve had the extraordinary privilege of
performing music for 30 years on stage and in the studio. As the principal visionary
of the company, every product we design reflects my energy, attitude and life experi-
ences.
Each amplifier we create is designed to help you tell your musical story...
IN 3D!!!
Rock on!
James Scott
Amp Artist & CEO
MOVING FORWARD... IN 3D
™
4
SPECIAL FEATURES:
• Hand-built and hand-wired in the USA
• Dual Channel All-Tube design
•Selectable 38W/18WEL34 Power Amp section
• HybridMASTER-PLUS™ Volume Management Technology
• American Channel 12AX7 Preamp Triode topology with Volume, Bass and Treble controls
plus Tweed/Blonde toggle switch
• British Channel 12AX7 Preamp Triode topology with Volume, Treble, Middle and Bass con-
trols plus Orange Glow toggle switch
• JUMP output jacks on both channels for custom signal routing options including running both
channels simultaneously
• Global Presence control
• 112 Combo Version features patent-pending SWITCHBACK™ speaker enclosure design
DIMENSIONS & WEIGHTS:
Subject to change anytime. Please measure your amp carefully if a custom case is being made.
These measurements do not include handle and rubber feet.
*112 Combo Dimensions (WxHxD): 25 x 22.85 x 10.5 in.
Weight: 57 lb.
*Amp Head Dimensions (WxHxD): 25 x 10 x 10.5 in.
Weight: 31 lb.
* Above dimensions are listed for the actual enclosure only (no feet or handle). When constructing a custom
travel case please take this into consideration.
5
Preparing to Operate your DREAM WEAVER™
Make certain that all connections are made prior to operating your DREAM WEAVER™ Amplifier
including power cable, speaker connection, instrument cable and instrument connection. Make
certain that all tubes are installed.
Power Switch (1)
The POWER switch, when placed in the UP position, provides AC wall power to the amplifier.
Standby Switch (2)
The STANDBY switch, when placed in the CENTER position, puts the amplifier in ‘standby mode’
allowing the tubes to warm up. When this switch is place in the UP position, the tube circuitry is
fully functional and operating in 38W (pentode) mode. In the DOWN position, the amplifier is
operating in 18W (triode) mode.
Presence Control (3)
The global PRESENCE control affects both channels and allows you to adjust the character or
‘forwardness’ of your sound. Low settings create ‘darker’ tones, whereas higher settings create a
‘brilliant’ or crisp sound.
FRONT PANEL:
12
3
6
Input Jack (4)
The INPUT jack is where you connect instrument level signals.
JUMP Jack (5)
The JUMP jack allows you to split your guitar’s signal and route it to the other channel. While
you’re at it, you can even patch in your favorite effects pedals for more tonal options.
Tweed/Blonde Switch (6)
The Tweed/Blonde toggle switch allows you to select the preamp operating mode for a variety
of tonal options.
“Tweed” Position: Wide and warm with special emphasis on the midrange frequencies. Clean
tones are earthy. Excellent overdrive tones when pushed.
“Blonde” Position: Tight and spanky with lots of headroom. Clean tones are fast and punchy. Big,
edgy overdrive tones when pushed.
Volume Control (7)
The VOLUME control allows you to adjust the signal level as well as the temperament and over-
all character of your instrument’s sound.
Treble & Bass Controls (8 & 9)
The TREBLE control allows you to adjust the character of the higher frequency range. The BASS
control allows you to adjust the depth of your lower frequencies.
FRONT PANEL: AMERICAN CHANNEL
4 5 6 7 8 9
7
Input Jack (10)
The INPUT jack is where you connect instrument level signals.
JUMP Jack (11)
The JUMP jack allows you to split your guitar’s signal and route it to the other channel. While
you’re at it, you can even patch in your favorite effects pedals for more tonal options.
Orange Glow Switch (12)
Switch the toggle in the upward position to go from vintage Plexi Mode to Orange Glow (hot-
rodded Plexi) Mode which significantly increases the overall saturation and harmonics of the dis-
tortion effect.
Volume Control (13)
The VOLUME control allows you to adjust the signal level as well as the temperament and over-
all character of your instruments sound. The British channel has been optimized to provide su-
perb versatility with a particular emphasis on tight mid-range frequencies to deliver a wide
range of clean, crunch to vintage overdrive and sustain.
Treble, Middle & Bass Controls (14, 15 & 16)
The TREBLE control allows you to adjust the character of the higher frequency range. The MID-
DLE control allows you to adjust the emphasis of the mid-range frequencies. The BASS control
allows you to adjust the depth of your lower frequencies.
FRONT PANEL: BRITISH CHANNEL
10 11 12 13 14 15 16
8
AC Input (17)
The AC INPUT socket (TYPE IEC Grounded) is a required connection for operating your amplifier
at 120V (standard USA household electrical power).
Mains Fuse (18)
The MAINS FUSE requires a 2 AMP fast-acting fuse. This fuse protects your amplifier from volt-
age peaks from your power outlet.
H.T. Fuse (19)
The H.T. FUSE requires a .3 AMP (300 milliamp) slow-blow fuse. The H.T. FUSE usually blows if
your power tubes are bad to protect the circuit from being damaged.
SAFETY NOTES:
• Always plug your amp into a properly grounded 3 prong AC outlet.
• Never plug your amp into an ungrounded outlet.
• Never remove or break off the 3rd prong safety ground pin from the power
cord.
• Never use a damaged or ungrounded power cord.
• Always use the proper value and type fuse according to the rear-panel
markings.
• Never attempt to replace the fuse while the amplifier is still plugged into
the power source. The fuse should only be replaced when the power cord
has been disconnected from its power source.
17 1918
BACK PANEL:
HybridMASTER-PLUS™
STAGE
STUDIO
MIN MAX
9
16-OHM Speaker Output (20)
The 16-OHM SPEAKER OUTPUT is provided for connecting your amplifier to standard 16 OHM
speaker cabinet.
8-OHM Speaker Output (21)
The 8-OHM SPEAKER OUTPUT is provided for connecting your amplifier to single 8-OHM
speaker, such as the internal speaker for the combo unit.
4-OHM Speaker Outputs (22)
The two (2) 4-OHM DISCREET SPEAKER OUTPUTs are provided for connecting your amplifier to
single 4-OHM speaker cabinet or for connecting two (2) 8-OHM speaker cabinets in parallel.
SAFETY NOTES:
• Never operate your amplifier without a connected speaker cabinet. This
will damage your tubes or transformers - or both.
• Always operate your amplifier with the proper impedance output that
matches your speaker cabinets(s).
• In all cases, always use a good quality heavy gauge speaker cable (not a
shielded instrument cable) to connect your amplifier to the speaker cabi-
net(s).
BACK PANEL:
20 21 22
10
HybridMASTER-PLUS™ (23)
The HybridMASTER-PLUS system allows you to set the overall volume level of the amplifier in-
dependent of the volume and tone settings established on the front panel. The system consists
of a “venue” switch and the HybridMASTER control. Use the switch to toggle between full scale
output and an approximate 80% reduction in volume. Use the HybridMASTER control to fine
tune your volume levels.
Effects Insert (24)
The EFFECTS INSERT of the DREAM WEAVER is designed to allow you to insert an effects device
(most often, time-based effects like delay or reverb) after the preamp and before the power amp.
When no effects device is present, this circuit is completely bypassed to deliver a direct signal
path between the preamp and power amp stage. For best results, utilize professional type effects
processors with at least +15dBu input sensitivity.
OPERATION NOTES:
• This is a line-level effects insert that is best suited for professional rack-
mount effects devices capable of handling up to 4.5Vrms.
• Best performance is achieved by minimizing patch cable length.
• When cable runs are over 5 - 10 feet it may be beneficial to use an exter-
nal effects buffer device on the SEND connection.
BACK PANEL:
2423
HybridMASTER-PLUS™
STAGE
STUDIO
MIN MAX
Tabla de contenidos
Otros manuales de Amplificador de 3rd Power
