3One data NP30XT series Manual de usuario

CLI user manual

NP30XT series serial device server

CLI user manual

Version 1.0.0, Mar. 2015

CLI user manual

Page1

Statement

Information in this document is reserved by Shenzhen 3onedata Technology Co., Ltd.

Reproduction and extract without permission is prohibited.

Trademarks Notice

and is registered trademarks of Shenzhen 3onedata

Technology Co.,Ltd. All other trademarks or regitered marks in this manual belong to their

respective manufacturers.

Agreement

As the product version upgrades or other reasons, this document is subject to change

without notice. Unless other agreement, this document only as a guide to use. All statement,

information and suggestion in this document, without warranty of any kind, either

expressed or implied.

Revision History：

Version No.

Date

Reason

V1.0.0

2013-07

First time to publish

V1.0.1

2013-09

Modify Documents

V1.0.2

2013-11

Software upgrade

V1.0.3

2015-03

Modify Documents

Notes

In reading this manual, please pay attention to the following symbols,

：Information necessary to explain.

：Special attention.

CLI user manual

Page2

Content

CHAPTER 1 ACCESS TO SERIAL SERVER SERIAL DEVICE SERVER..............................1

1.1 CONFIGURATION THROUGH TELNET.............................................................................................1

1.2 AGREEMENT................................................................................................................................2

1.3 COMMAND LINE PORT ..................................................................................................................2

1.3.1 View of Command Lines.....................................................................................................2

1.3.2 Command lines Online help.................................................................................................3

1.3.3 Frequent Incorrect Information of Command Lines............................................................4

1.3.4 History command.................................................................................................................4

CHAPTER 2 DEVICE SYSTEM BASED INFORMATION CONFIGURATION.....................5

2.1ENTER INTO THE VIEW OF DEVICE INFORMATION ..........................................................................5

2.2DISPLAY DEVICE INFORMATION ....................................................................................................5

2.3 CONFIGURATION INFORMATION ...................................................................................................6

2.4DELETE DEVICE INFORMATION .....................................................................................................6

CHAPTER 3 INFORMATION CONFIGURATION.....................................................................7

3.1 ENTER INTO SERIAL CONFIGURATION VIEW ..................................................................................7

3.2 DISPLAY SERIAL INFORMATION ....................................................................................................8

3.3 CLEAR SERIAL INCORRECT INFORMATION..................................................................................10

3.4 SERIAL PARAMETER CONFIGURATION.........................................................................................10

3.5 WORKING MODE PARAMETER CONFIGURATION ..........................................................................11

CHAPTER 4 SYSTEM MANAGEMENT ....................................................................................14

4.1 ENTER INTO THE VIEW OF SYSTEM MANAGEMENT CONFIGURATION...........................................14

4.2DISPLAYADDRESS INFORMATION................................................................................................14

4.3OVERTIME TIME CONFIGURATION ...............................................................................................15

4.4IPADDRESS,DEFAULT GATEWAY.................................................................................................15

4.5USER NAME,PASSWORD CONFIGURATION...................................................................................15

4.6FACTORY DEFAULT......................................................................................................................15

4.7 UPLOAD AND DOWNLOAD CONFIGURABLE FILES ......................................................................16

4.8 SYSTEM UPGRADE .....................................................................................................................16

CLI user manual

Page1

CHAPTER 1 Access to Serial server serial device server

The CLI user manual compliant with the products as follows:

NP302-2D(RS-232), 2 port RS-232 to Ethernet;

NP302-2D(RS-485), 2 port RS-485/422 to Ethernet;

NP304-4D(RS-232), 4 port RS-232 to Ethernet;

NP304-4DI(RS-485), 4 port RS-485/422 to Ethernet;

NP308-8D(RS-232), 8 port RS-232 to Ethernet;

NP308-8DI(RS-485), 8 port RS-485/422 to Ethernet;

NP3016-16D(RS-232), 16 port RS-232 to Ethernet;

NP3016-16DI(RS-485), 16 port RS-485/422 to Ethernet;

1.1 Configuration through Telnet

Terminal device use telnet connect to Serial server through PC, the requirements are as follows:

1. The IP address of Serial server, can get it by search or modify (Use IP command under the system management

view);

2. If PC and serial device server in the same local area network, the IP address must in a same network segment,

otherwise, PC and serial device server must cross-router.

If satisfied these two requirements, can use telnet access to serial device server, and then configure the serial

device server.

1）Establish configuration environment, just connect PC ‘s Ethernet port connect to serial device server’s

Ethernet port through Local area network

2）Before access Serial server through Telnet, need to input“Telnet+ Space+ serial server’s IP address”for

checking, Figure 1.1.1 as follows:

（Figure 1.1.1）

3）Hit “Enter”, checkout successful and till PC show“Please input hostname and password”, ask user to input

user name and password, default is admin, figure 1.1.2 as follows:

（Figure 1.1.2）

CLI user manual

Page2

4）Use command to configure Serial server and check the running statues, if need help, please input“?”at

any time. Specific configuration command, please reference“Serial server user manual”.

1.2 Agreement

1. Command line format agreement table 1.2.1 as follow

Table 1.2.1

Bold

Key words of the command show by bold type.

italic

Parameter of the command show italic type.

[ ]

It shows part in “[]”is optical when command configuration is need.

{ x | y | ... }

It shows to pick up one from two or more items.

[ x | y | ... ]

It shows to pick up one or no one from two or more items.

{ x | y | ... }

It shows to pick up one at least, all at most from two or more items.

Bold

Key words of the command show by bold type.

2. Format agreement of figure interface Table 1.2.2 as follows:

Table 1.2.2

Format

Description

< >

“< >” shows press name, like ”click<OK>”

[ ]

“[ ]” shows windows name, menu name and data list. like “eject [create user]window”

Multilevel is separated by “/”. Like [file/create/folder] means[create] a [folder] under the

menu of [file]

1.3 Command line port

Serial server provides command lines port and its configuration for user’s easy configuration and

management. Command lines port includes the following features:

1. Local configuration through Console port;

2. Supports history command saving which means it can save 10 pieces. History commands can be selected

by up and down key.

3. User can type in “help” or”?” to get some help;

4. Supports intelligent complement with Tab when commands input;

5. Command interpreter take the method of partial matching. User can type in conflict-free key words, such

as config command, only need to type in conf.

1.3.1 View of Command Lines

Serial server’ view of command lines aim at configuration of different functions. First of all, Serial server

establish connection, then confirmation of user name and password finished, after enter the correct user name

and password, enter “help or ?” in “switch”, enter into system view, Under the view of system, corresponding

view appears after typing indifferent command, figure 1.3.1 as follows:

CLI user manual

Page3

（Figure 1.3.1）

Table 1.3.1 system view command list

View

Function

DOS Prompt

Enter

Quit

System View

Switch#

Help or

？

Quit and

return to

user login

Information

Show or modify device

information, like software

version, IP address, etc.

Switch (information)#

Information

Exit and

return to

the view of

system

Serial device

server

Show or modify serial

information，like as baud

rate, data bit, mode

configuration

Switch (Serial)#

Serial

Manage

Show or modify configuration

information, like IP address，

subnet mask, default gateway

and password, etc.

Switch (manage)#

Manage

1.3.2 Command lines Online help

Command lines port provides the following online help:

Total help;

Partial help;

1. Total help

1）Type in <?> to get all commands and their description.

Example：

Switch#?

List --List commands of current view

Help --Help commands of current view

Quit --Exit from CLI

Exit --Exit from current view

Reboot --Reboot switch

CLI user manual

Page4

Port --Enter port setting view

Serial --Enter Serial setting menu

Manage --Enter system manage view

Information --Enter device information view

2）Type in a command and “?”, between there is a space, if key word is in this location, then type in all keywords

and descriptions.

Example:

Switch (information)# show ?

mac --show device MAC Address

version --show device version

others --show device type、name、etc

2. Partial help

1）Type in a character string with <?>. It can show all commands beginning with this character string.

Example:

Switch# m?

Manage --Enter system manage menu

2）Type in former letters of some key word of the command, press<Tab> key. If the letters are unique, it can

show the completed key word.

Example:

Switch# inf+<Tab>

Switch# information

1.3.3 Frequent Incorrect Information of Command Lines

All commands typed by users, if it is certificated by grammar, it can run correctly, or users will be sent

incorrect information. Frequent incorrect information is in table 1.4.3 as below:

Table 1.4.3 Frequent incorrect information

English incorrect information

Reason

Invalid Command

Command cannot be found.

Key word cannot be found.

The type of parameter is wrong.

The parameter is beyond the border.

Incomplete Command

Command is not completed.

Too many parameters

Parameter is too much.

Must OneToOne option!

Based mode is necessary

1.3.4 History command

Command lines port can provides the function similar to Dos key. It automatic saves command lines that

users types in, and users can use these history commands. Detailed operating please check table 1.3.4

as follows:

Table 1.3.4 access history command

Operating

Key

Result

Visit previous history command Up <↑> If it exists earlier command, it is taken out.

Visit next history command

Down <

↓

If it exists later command, it is taken out.

CLI user manual

Page5

CHAPTER 2 Device system based information configuration

Device information includes Device Type, Hardware Version, Device Name, Software Version, Device

Description, Device SN and Contact Way. Among them, Hardware Version and Software Version can be only read,

not modified.

2.1 Enter into the view of device information

Please check the view as figure 2.1.1 Table 2.1.1

Operating

Command

Description

Enter into the view of device information

Information

Run in the view of system

2.2 Display device information

Please check the device information command as table 2.2.1

Table 2.2.1

Operating

Command

Description

Show system version

show version

Carry out under the view of device information

Show MAC address of device

show mac

Carry out under the view of device information

Show Device Type, Name, etc.

show others

Carry out under the view of device information

Configure device model, name etc

config

Carry out under the view of device information

Delete device model, name etc

clean

Carry out under the view of device information

Example: Enter into device information view, enter the bold type command as follows and enter return key

Switch# information

Switch(information)# ?

List --List commands of current menu

Help --Help commands of current menu

Quit --Quit from CLI

Exit --Exit from current menu

Reboot --Reboot switch

Show mac --Show device MAC Address

Show version --Show device version

Show others --Show device type,name,etc

Config --Config device type,name,etc

Clean --Clean device type,name,etc /

Example: Check device name and model number etc

Switch (information)# show others

Device type Serial server

Device name Serial server

Description Serial Server

Serial number 201304160001

Contact way www.3onedata.com

Example: Check the MAC address

Switch(information)# show mac

Device MAC address : 00.22.6F.BB.00.02

CLI user manual

Page6

2.3 Configuration information

Please reference user configuration device information as table 2.3.1:

Table 2.3.1

Operating Command Description

Configure Device Type config –t type

Type: configurable type, the length is between

1～17 characters

Configure Device Name config -n name

Name: configurable name, the length is

between1～17 characters

Configure Serial Number config -m number

Number: configurable number, the length is

between 1

～

17 characters

Configure Device Description config -p description

Description: configurable description, the length

is between 1～17 characters

Configure Contact information

config -c contact

Contact: Configure Contact way 1-17 bytes

Example: Configure device name as AB123, enter the bold type command as follows and enter return key:

Switch(information)# config -n ABC123

[OK]

Example: Configure device serial number as 201304111, enter the bold type command as follows and enter return

key:

Switch(information)# config -m 201304111

[OK]

2.4 Delete device information

Please reference table 2.4.1 Table 2.4.1

Operating Command Description

Delete Device Type

Clean–t