3One data CP202-2CI Manual de usuario

CP202-2CI

CAN Server

Quick Installation Guide

3onedata Co., Ltd.

Address: 3/B, Zone 1, Baiwangxin High Technology

Industrial Park, Xili, Nanshan District, Shenzhen

Website: www.3onedata.com

Tel: +86 0755-26702688

Fax: +86 0755-26703485

【Packagechecklist】

Please check the integrity of package and accessories while

first using the switch.

1. CAN server X1 (with wiring terminal block)

2. Certification 3. Wall mounting accessories

4. Manual 5. CD

6. Warranty card

If any of these items are damaged or lost, please contact our

company or dealers, we will solve it asap.

【ProductsOverview】

CP202-2CI is a CANserver, the model is CP202-2CI(2-way

CAN bus ports to 1-way 10/100 Base-T(X) converter).

【Paneldesign】

Front view

Left view and right view

1. CAN status indicator CAN1

2. System running indicator RUN

3. Network connection indicator LINK

4. Lugs

5. CAN status indicator CAN2

6. Indicator ERR2

7. Indicator ERR1

8. Ethernet RJ45 port

9. Restore default settings DEF

10. Power input terminal block

11. CAN wiring terminal block

【MountingDimension】

Unit (mm)

【Wall-mountedDeviceMounting】

Step 1 Place the CAN server on the wall as reference or

reference installation dimension; label the bolt

position on the wall.

Step 2 Hang the CAN server on the labeled wall; align the

bolt to the labeled position, then screw the bolt to

enhance stability, installation ends.

Note:

1. Don't place or install the device in area near water or

moist, keep the relative humidity of the device

surrounding between 5%~95% without condensation.

2. Before power on, first confirm the supported power

supply specification to avoid over-voltage damaging

the device.

【Wall-mountedDeviceDisassembling】

Step 1 Screw out the bolt in the wall.

Step 2 Lift the device outward slightly; take out the device,

disassembling ends.

【PowerSupplyConnection】

DC power supply

The device supports 1-way DC power input

(VI+, VI-), 4-pin 5.08mm pitch industrial

wiring terminal blocks, another terminal

block (VO+, VO- ) is reserved. Power supply range: 9～

24VDC.

Note:

1. Power ON operation: First insert the power supply

terminal block into the device power supply interface,

and then plug the power supply plug contact and power

on.

2. Power OFF operation: first unpin the power plug, then

remove the terminal block wiring part, please note the

operation order above.

【RestoreDefaultSettings】

DEF is restoring default

settings button. Restoring

default settings steps as

follows: Press and hold

the DEF button,

disconnect the power supply and then give the device to

power up, wait for about 3~4 seconds to restore the factory

settings.

【CANPort Connection】The device has 2-way

CAN-Bus Ports, 10 pins,

1~5 pin are the first

CAN port, 2~10 pin are the second CANport. CAN-Bus Port

adopts 10 bits 5.08mm pitch industrial wiring terminal block,

and pin define as follow.

NO.

Name

Description

CAN2L

CAN2 port CANL Signal

CAN2H

CAN2 port CANH Signal

R2ES+

CAN2 port Terminal Resistor

Connector (built-in 120Ω

terminal resistor, direct

connection)

R2ES-

SHELL

Shell Ground

SHELL

Shell Ground

R1ES-

CAN1 port Terminal Resistor

Connector (built-in 120Ω

terminal resistor, direct

connection)

R1ES+

CAN1H

CAN1 port CANH Signal

CAN1L

CAN1 port CANL Signal

【LEDIndicator】

The device provides LED indicators to monitor the device

working status with a comprehensive simplified

troubleshooting; the function of each LED is described in the

table as below:

LED

State

Description

LINK

LAN port connection is active

Blinking

LAN port is in network active

status

OFF

LAN port connection is inactive

RUN

Blinking

System is running normally

OFF

System is not running or

running abnormally

System is running abnormal

ERR1

CAN1 port work appears fault

OFF

CAN1 port is working normally

ERR2

CAN2 port work appears fault

OFF

CAN2 port is working normally

CAN1

OFF

CAN1 port without data

transmission or data

transmission abnormal

Blinking

CAN1 port exists data

transmission

CAN2

OFF

CAN2 port without data

transmission or data

transmission abnormal

Blinking

CAN2 port exists data

transmission

【Loggingin to WEB Interface】

This device supports WEB management and configuration.

Computer can access the device via Ethernet interface. The

way of logging in to device’s configuration interface via IE

browser is shown as below:

Step 1 Configure the IP addresses of computer and the

device to the same network segment, and the

network between them can be mutually accessed

Step 2 Enter device’s IP address in the address bar of

the computer browser.

Step 3 Enter device’s username and password in the

Step 4 Click “OK”button to login to the WEB interface of

the device.

Note:

The default IP address of the device is

“192.168.1.254”.

The default username and password of the device is

“admin”.

If the username or password is lost, user can restore it

to factory settings via device DIP switch or

management software; all modified configurations

will be cleared after restoring to factory settings, so

please backup configuration file in advance.

Please refer to user manual for specific configuration

method of logging in to WEB interface and other

configurations about network management function.

【Specification】

Panel

10/100 Base-T(X)

self-adapting RJ45 port, full

duplex or half duplex

self-adapting, support

MDI/MDI-X self-adapting

CAN port

The second CAN port, 10-pin

5.08mm pitch industrial wiring

terminal blocks

Indicator

Connection indicator, run

indicator, ERR indicator, CAN

indicator

Power supply

Input power supply

9 ~ 24VDC

Access terminal block

4 bits 5.08mm pitch industrial

wiring terminal blocks

Consumption

No-load consumption

1.0W@12VDC

Full-load consumption

1.1W@12VDC

Working environment

Working temperature

-40℃～75℃

Storage temperature

-40℃～75℃

Working humidity

5%～95% (no condensation)

Protection grade

IP40 (metal shell)

Otros manuales de Servidor de 3One data

3One data

3One data NP Series Manual de usuario

3One data

3One data NP308T-8D Manual de usuario

3One data

3One data NP302T Series Manual de usuario

3One data

3One data NP5100 Series Manual de usuario

3One data

3One data NP30XT series Manual de usuario

3One data

3One data NP316Series Manual de usuario

3One data

3One data NP301 Manual de usuario

3One data

3One data NP5100 Series Manual de usuario

3One data

3One data NP301 Instrucciones de funcionamiento y mantenimiento

3One data

3One data NP318T-8DI Manual de usuario

3One data

3One data NP316 Manual de usuario

3One data

3One data NP5000 Series Manual de usuario

3One data

3One data NP302T Series Manual de usuario

3One data

3One data NP3 T Series Instrucciones de funcionamiento y mantenimiento

3One data

3One data NP318T-8DI Manual de usuario

3One data

3One data ICP222-2F-2CI Instrucciones de funcionamiento y mantenimiento

3One data

3One data CP202-2CI Manual de usuario

3One data

3One data NP318T-8DI Instrucciones de funcionamiento y mantenimiento

3One data

3One data NP3116T Series Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario