3M LM1 Manual de usuario

Best practice guidance:

Charging your 3M™ Clean-Trace™ LM1 Luminometer

On receipt of your Clean-Trace LM1 luminometer:

Charging your LM1 instrument to a full battery should usually take around 2 hours but on

occasions a longer charge may be required.

Charging your Clean-Trace LM1 luminometer for continued use:

Ensure the luminometer is routinely charged. You can use the battery level indicator to keep

the luminometer charged to a reasonable level

The battery level indicator is in the upper right corner of the screen.

When the luminometer is switched on, the indicator shows the remaining battery level.

In Figure 1, the indicator shows the battery is fully charged.

As the battery charge decreases, the blue segment of the indicator becomes smaller.

When the battery level is less than 10%, the indicator becomes red, showing the battery

should be recharged.

When the battery level is less than 5%, the LM1 luminometer will automatically shut down.

It is advisable to maintain the charge of your luminometer in the ‘blue’ zone of the battery

indicator. Avoid the battery going below 5% charge and switching off.

Switching off your Clean-Trace LM1 luminometer correctly

In order to maintain the battery life of your luminometer, it is advised to switch it off correctly

after use following the process below.

1. Press the on/off button for 3 seconds.

2. [Power off] appears on the screen to confirm the power off process has started.

3. Tap [Power off].

4. A confirmation message the luminometer will shut down appears.

5. Tap [OK]. The display screen goes black to confirm the power off process has completed.

6. Or, tap [Cancel] to cancel the power off process if you wish to continue using the

luminometer.

Sleep Mode

The Clean-Trace LM1 luminometer conserves battery power if the touch screen or the cursor

control buttons are inactive. After 5 minutes of inactivity, the luminometer goes into Sleep

mode and the screen darkens.

After 2 further hours of inactivity, the luminometer automatically shuts down and must be

powered on again before use.

Waking the Clean-Trace LM1 luminometer from Sleep Mode

1. Press and hold the up-arrow button on the cursor control pad for 3 seconds.

2. The screen displays the information that appeared before the Sleep mode began so you can

continue working.

If the luminometer does not wake from the Sleep mode, the luminometer might be turned off.

Press and hold the on/off button for 3 seconds to turn it on.

If the battery is at a low charge before the luminometer goes into Sleep mode, this may result

in the battery becoming completely discharged. This will then result in the luminometer failing

to switch on due to insufficient charge.

In this case, the luminometer will need to be put on charge from the mains charger (not the PC

USB). After 30 minutes of charging you should then be able to switch on the machine

however it will likely require further charge to reach adequate charge for use. To maintain

battery performance, the luminometer should be switched on within 3 hours after placing the

unit on charge.

For further support, please visit www.3M.com/foodsafety/cleantracesupport

Web: www.3M.com/foodsafety Email: emeafoodsaf[email protected]m

3M and Clean-Trace are trademarks of 3M. © 3M 2018

Otros manuales para LM1

2

Tabla de contenidos

Otros manuales de Instrumento de medición de 3M

3M

3M RFO 144 Manual de usuario

3M

3M WIBGET WB-300 Manual de usuario

3M

3M EVM Series Manual de usuario

3M

3M NoisePro Series Manual de usuario

3M

3M SCOTT SEMS II PRO Guía de solución de problemas

3M

3M SD-200 Manual de usuario

3M

3M TN2000 Manual

3M

3M SoundPro SE series Manual de usuario

3M

3M SpotOn 370 Manual de usuario

3M

3M Dynatel 7550 Series Manual de usuario

3M

3M SoundPro SE Series Instrucciones de instalación y funcionamiento

3M

3M Edge Manual de usuario

3M

3M 1100 SLM Manual de usuario

3M

3M ScanEM-C Manual de usuario

3M

3M CTM048 Manual de usuario

3M

3M The Edge Manual de usuario

3M

3M Workstation Monitor 724 Manual de usuario

3M

3M LM1 Manual de usuario

3M

3M Dynatel 965AMS Manual de usuario

3M

3M GMI PS200 Series Manual

3M

3M Stormscope Series 2 Manual de usuario

3M

3M Dynatel 2250M Manual de usuario

3M

3M Edge eg5 Manual de usuario

3M

3M PROTEGE PLUS Manual de instrucciones

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario