3M Matic 700r Hoja de datos
3M Packaging Systems Division
3M Center, Building 220-8W-01
St. Paul, MN 55144-1000
Serial No. For reference, record machine serial number here.
"3M-Matic"and "AccuGlide" are Trademarks
of 3M, St. Paul, MN 55144-1000
Litho in U.S.A.
© 3M 1999 44-0009-1907-4 (D29.00)
3M-Matic
TM
AccuGlide
II
TM
Instructions and Parts List
700r Type 39600
Random
Case Sealer
with
Taping Heads
Important Safety
Information
Read "Important Safeguards",
pages 3-6 and also
operating "Warnings",
page 19 BEFORE
INSTALLING OR
OPERATING THIS
EQUIPMENT.
It is recommended you
immediately order the spare
parts listed on page 37,
Section I and page 17,
Section II. These parts are
expected to wear through
normal use and should be
kept on hand to minimize
production delays.
Spare Parts
Replacement Parts and Service Information
3M Packaging Systems Division
3M Center, Building 220-8W-01
St. Paul, MN 55144-1000
To Our Customers:
This is the 3M-Matic™/AccuGlide™/Scotch™ brand equipment you
ordered. It has been set up and tested in the factory with "Scotch" brand
tapes. If technical assistance or replacement parts are needed, call or Fax
the appropriate number listed below.
Included with each machine is an Instructions and Parts List manual.
Replacement Parts and Additional Manuals
Order parts by part number, part description and quantity required. Also,
when ordering parts and/or additional manuals, include machine name,
number and type. A parts order form is provided at the back of this manual.
3M/Tape Dispenser Parts
241 Venture Drive 1-800/344 9883
Amery, WI 54001-1325 FAX# 715/268 8153
Technical Assistance:
3M-Matic™ Helpline – 1-800/328 1390. Please provide the customer support
coordinator with the machine number, machine type/model and serial number.
If you have a technical question that does not require an immediate response,
you may Fax it to 715/381 0248.
Minimum billing on parts orders will be $25.00. Replacement part prices available on request.
Note : Outside the U.S., contact the local 3M subsidiary for parts ordering information.
$10.00 restocking charge per invoice on returned parts.
"3M-Matic", "AccuGlide" and “Scotch” are trademarks of
3M, St. Paul, Minnesota 55144-1000
Printed in U.S.A.
© 3M 1999 44-0009-1851-4(E79.0)
Replacement Parts And Service Information
To Our Customers:
This is the 3M-Matic™/AccuGlide™/Scotch™ brand equipment you
ordered. It has been set up and tested in the factory with "Scotch" brand
tapes. If any problems occur when operating this equipment, and you
desire a service call, or phone consultation, call, write or Fax the
appropriate number listed below.
Included with each machine is an Instructions and Parts List manual.
SERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALS
AVAILABLE DIRECT FROM:
Order parts by part number, part description and quantity required. Also, when
ordering parts and/or additional manuals, include machine name, number and
type.
1-800/328 1390
"3M-Matic", "AccuGlide" and “Scotch” are trademarks of
3M, St. Paul, Minnesota 55144-1000
Printed in U.S.A.
© 3M 1999 44-0009-1852-2(D79.0)
3M Packaging Systems Division
3M Center, Building 220-8W-01
St. Paul, MN 55144-1000
Instruction Manual
700r, Random Case Sealer, Type 39600
This instruction manual is divided into two sections as follows:
Section IIncludes all information related to installation, operation and parts for the case sealer.
Section II Includes specific information regarding the AccuGlide™ II STD 2 Inch Taping Heads.
Table of Contents Page
Section I– 700r Random Case Sealer
Description ........................................................................................................................................ 1
Equipment Warranty and Limited Remedy ....................................................................................... 2
700r Contents.................................................................................................................................... 2
Important Safeguards........................................................................................................................ 3 - 6
Specifications .................................................................................................................................... 7 - 9
Installation and Set-Up...................................................................................................................... 10 - 14
Receiving and Handling ....................................................................................... 10
Machine Set-Up ................................................................................................... 10 - 14
Packaging and Separate Parts .................................................................. 10 - 12
Infeed Conveyor Assembly ........................................................................ 12
Centering Guides ....................................................................................... 12
Machine Bed Height................................................................................... 13
Outboard Tape Roll Mounting .................................................................... 13
Tape Leg Length ........................................................................................ 13
Bumper Supports ....................................................................................... 14
Box Size Capacity of Case Sealer ............................................................. 14
Electrical Connection and Controls ............................................................ 14
Initial Start-Up of Case Sealer.................................................................... 14
Operation .......................................................................................................................................... 15 - 21
Operating "Warnings" .......................................................................................... 19
Machine Switches and Controls........................................................................... 16 - 18
Tape Loading/Threading...................................................................................... 19
Theory of Operation ............................................................................................. 20 - 21
Box Sealing.......................................................................................................... 21
i
(Table of Contents continued on next page)
Table of Contents (Continued) Page
Maintenance...................................................................................................................................... 22 - 24
Cleaning............................................................................................................... 22
Lubrication ........................................................................................................... 22
Box Drive Belt Replacement ................................................................................ 23
Circuit Breaker ..................................................................................................... 24
Knife Replacement, Taping Head ........................................................................ 24
Adjustments ..................................................................................................................................... 25 - 27
Box Drive Belt Tension ........................................................................................ 25 - 27
Taping Head Adjustments.................................................................................... 27
Special Set-Up Procedure................................................................................................................. 29 - 32
Changing Tape Leg Length ................................................................................. 29 - 30
Box and Machine Bed Height Range................................................................... 31
Box Height Range................................................................................................ 32
Troubleshooting ................................................................................................................................ 33 - 34
Electrical Diagram ............................................................................................................................. 35
Pneumatic Diagram........................................................................................................................... 36
Replacement Parts and Service Information..................................................................................... 37
Spare Parts .......................................................................................................... 37
Label Kit ............................................................................................................... 37
Tool Kit................................................................................................................. 37
Options/Accessories ......................................................................................................................... 38
Replacement Parts Illustrations and Parts Lists......................................................(Yellow Section) 39 - 67
ii
Section II – AccuGlide™ II STD 2 Inch Taping Heads
(See Section II for Table of Contents)
1
Description
The 3M-MaticTM 700r Random Case Sealer with AccuGlideTM II Taping Heads is designed to apply a “C” clip of
ScotchTM brand pressure-sensitive film box sealing tape to the top and bottom center seam of regular slotted
containers. The 700r automatically adjusts to a wide range of box sizes (see "Specifications – Box Weight and
Size Capacities", Page 8).
3M-MaticTM 700r Random Case Sealer, Type 39600 (Note – Lower tape supply roll and bracket assembly are
shown in the alternate location)
2
ScotchTM,AccuGlideTM, and 3M-MaticTM are Trademarks of 3M, St. Paul, Minnesota 55144-1000
Contents – 700r Random Case Sealer
(1) 700r Random Case Sealer, Type 39600
(1) Upper Tape Drum/Bracket/Hardware
(2) Column Bumper Bracket/Hardware
(1) Tool/Spare Parts Kit
(1) Instruction and Parts Manual
Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, A CUSTOM OR
USAGE OF TRADE:
3M sells its 3M-Matic™ 700r, Type 39600 with the following warranties:
1. The drive belts and the taping head knives, springs and rollers will be free from all defects for ninety
(90) days after delivery.
2. All other taping head parts will be free from all defects for three (3) years after delivery.
3. All other parts will be free from all defects for two (2) years after delivery.
If any part is proved to be defective within its warranty period, then the exclusive remedy and 3M’s and seller’s
sole obligation shall be, at 3M’s option, to repair or replace the part, provided the defective part is returned
immediately to 3M’s factory or an authorized service station designated by 3M. A part will be presumed to
have become defective after its warranty period unless the part is received or 3M is notified of the problem no
later than five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a
reasonable time, then 3M at its option, will replace the equipment or refund the purchase price. 3M shall have
no obligation to provide or pay for the labor required to install the repaired or replacement part. 3M shall have
no obligation to repair or replace (1) those parts failing due to operator misuse, carelessness, or due to any
accidental cause other than equipment failure, or (2) parts failing due to non-lubrication, inadequate cleaning,
improper operating environment, improper utilities or operator error.
Limitation of Liability: 3M and seller shall not be liable for direct, indirect, special, incidental or consequential
damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal
theory.
The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability may be changed only by a
written agreement signed by authorized officers of 3M and seller.
3
Important Safeguards
Figure 1-1 – Knife Warning Label Figure 1-3 – Box Drive Belt Warning Label
This safety alert symbol identifies
important messages in this manual.
READ AND UNDERSTAND THEM BEFORE
INSTALLING OR OPERATING THIS
EQUIPMENT.
Important – In the event the following safety
labels are damaged or destroyed, they must be
replaced to ensure operator safety. A label
kit, part number 78-8098-9177-9 is available as
a stock item or individual labels can be ordered.
See Parts Illustration/List, Section I, pages 66
and 67.
Figure 1-2 – Electrical Warning Label
The "Warning – Hazardous Voltage" label, shown
in Figure 1-2, is attached to the cover of the
electrical control box. The label warns service
personnel to unplug the power supply before
attempting any service work on the case sealer.
The "Warning – Moving Belts" labels, shown in
Figure 1-3, are attached to both sides of the upper
belt guards at the infeed end of the machine. The
labels warn operators to keep hands or loose
clothing away from this area because of moving
belts.
The "Warning – Sharp Knife" label (A), shown in
Figure 1-1, is attached to both sides of the upper
frame at the location of the cut-off knife on the upper
taping head. The "Warning – Sharp Knife" label
(B) shown in Figure 1-1, is attached to the orange
cut-off knife guard on both taping heads. The labels
warn operators and service personnel of the very
sharp knife used to cut the tape at the end of the
tape application.
4
Important Safeguards (Continued)
Figure 1-6 – Stop and On/Off Labels
The "Caution – Pinch Point" label, shown in
Figure 1-5, is attached to the upper end of both
column guards. It warns the operator to keep hands
away from this area when machine is operating.
Figure 1-4 – Pinch Point Caution Label
Figure 1-7 – Safety Instructions Label
Figure 1-5 – Hands Caution Label
A red emergency stop switch is located on the top/
front of the upper drive assembly. The "Stop" label
shown in Figure 1-6, is located near the switch and
reminds operators and casual personnel of the
function of this switch. In addition, an "On/Off" label
is attached next to the electrical On/Off switch on the
side of the machine frame.
The "Caution – Pinch Point" label, shown in
Figure 1-4, is attached to the center plate at the exit
end of the machine bed. The label warns the
operator to keep hands out of this area when the
drive belts are running.
The "Safety Instructions" label, shown in
Figure 1-7, is attached to the top/front of the upper
drive assembly. The label provides convenient
safeguard instructions for the operator and service
personnel.
5
Important Safeguards (Continued)
Figure 1-8 – Air Pressure Label
The "Notice – Taping Head Latch" label, shown in
Figure 1-9, is attached to the top surface of the
upper, left belt guard at the front edge of the taping
head. The label reminds operators and service
personnel to keep latch down except to remove
taping head.
The "Notice – Raise and Lower Upper Drive
Assembly" label, shown in Figure 1-10 is attached
to the left column guard at the location of the
mechanical latch. The label provides instructions on
raising, latching/unlatching and lowering the upper
drive assembly.
The "Safety Instructions" and "Air Pressure"
labels, shown in Figure 1-8, reminds operator or
service personnel of the recommended air pressure
required and location of On/Off air valve.
Figure 1-10 – Upper Taping Latch LabelFigure 1-9 – Upper Taping Latch Label
Tabla de contenidos
Otros manuales de Ahorrador de alimentos de 3M
3M
3M Matic 800at Hoja de datos
3M
3M Matic 700r-s Hoja de datos
3M
3M 3M-Matic 700r3 Hoja de datos
3M
3M 3M MATIC A80F Hoja de datos
3M
3M 3M-Matic 700a Hoja de datos
3M
3M 40800 Hoja de datos
3M
3M 3M Matic 120af Hoja de datos
3M
3M Matic 7000a Hoja de datos
3M
3M 3M-Matic 200a Hoja de datos
3M
3M 3M-Matic 7000r Hoja de datos
3M
3M Matic 700a3 Hoja de datos
3M
3M 3M-Matic AccuGlide 3 200a Hoja de datos
3M
3M 3M-Matic 800asb Hoja de datos
3M
3M 3M-Matic 800a3 Hoja de datos
3M
3M 3-M Matic Accuglide 4 Hoja de datos
3M
3M 3M-Matic 700a Hoja de datos
3M
3M 3M-Matic 7000r-I Hoja de datos
3M
3M 3M-Matic 8000a Hoja de datos
3M
3M 3M-Matic 7000a Pro Hoja de datos
3M
3M Matic 8000a-I Hoja de datos
