3Com 3CB9LG9MC Manual de usuario

9-Port 1000BASE-SX

Gigabit Ethernet

Layer 2 Switching Module

Quick Start Guide

For the CoreBuilder®9000 Enterprise Switch

Module Description The 9-port 1000BASE-SX Gigabit Ethernet Layer 2 Switching Module

(Model Number 3CB9LG9MC) for the CoreBuilder®9000 Enterprise

Switch can switch Gigabit Ethernet (GEN) connections to corporate

backbones and servers. The module has nine 1000BASE-SX GEN front

panel ports. It has the following number of backplane ports for

connection to the 24-port and the 9-port GEN Switch Fabric Modules:

The 9-port Gigabit Ethernet Layer 2 Switching Module (9-port GEN

Layer 2 Switching Module) includes its own embedded management

agent that supports standard Simple Network Management Protocol

(SNMP) Management Information Bases (MIBs).

Key Features The 9-port GEN Layer 2 Switching Module supports these features:

■Hot-swapping of modules

■Management using the Administration Console

(a command line interface), the Web Management suite of

applications with an Internet browser, or SNMP-based applications

Backplane Port

Connections to the

24-port GEN Switch

Fabric Module

Backplane Port

Connections to the

9-port GEN Switch

Fabric Module

7-slot Chassis 3 1

8-slot Chassis 3 1

16-slot Chassis 2NA

29-Port 1000BASE-SX Gigabit Ethernet Layer 2 Switching Module Quick Start Guide

For information about the software features that this module supports,

see the:

■CoreBuilder 9000 Implementation Guide

■Command Reference Guide

■CoreBuilder 9000 Release Notes for the Fast Ethernet and Gigabit

Ethernet Layer 2 Switching Modules

Front Panel Figure 1 identifies the components on the module front panel.

Figure 1 Front Panel for the 9-Port GEN Layer 2 Switching Module

In the 7-slot chassis, you install the module horizontally with the LEDs at

the left. In the 8-slot chassis and 16-slot chassis, you install the module

vertically with the LEDs at the top.

Fiber-optic ports

(SC connectors)

MOD STAT

Model number

Ejector handle

Module Status LED

Port Status LEDs

Ejector handle

3CB9LG9MC

9-Port 1000BASE-SX Gigabit Ethernet Layer 2 Switching Module Quick Start Guide 3

Audience Description This guide is intended for trained technical personnel only. Do not

attempt to install, remove, or replace the 9-port GEN Layer 2 Switching

Module if you have not had the proper training from 3Com. For training

information in the United States and Canada, call 1-800-NET-3COM. For

the number to call in other locations, visit the 3Com Web site:

www.3Com.com/support/

Safety Precautions When you handle components in a CoreBuilder 9000 system, be sure

that you follow all safety precautions. To avoid electric shocks, burns, or

equipment damage, read and follow these warnings:

WARNING: Allow only trained service personnel to install, remove, or

replace any module in the chassis.

WARNING: Hazardous energy exists within the system. Use extreme

caution when you install, remove, or replace any module in the chassis.

When the system is on:

■Never insert metal objects such as a screwdriver or a finger with

jewelry into open module slots.

■Do not touch any connections within the chassis with your hands or

fingers.

WARNING: To ensure optical safety when installing the Gigabit Ethernet

Layer 2 Switching Module, comply with the following precaution:

Although the data communication LEDs used in this product meet the

regulatory requirements for casual exposure to the eye, as with any

source of bright light, it is advised that you do not look into the light

source.

LED Safety Information: IEC 825 and EN60825, Class 1 LED Device. For

connection only to Class 1 LED Device

CLASS 1

LED PRODUCT

49-Port 1000BASE-SX Gigabit Ethernet Layer 2 Switching Module Quick Start Guide

ESD Safety Information

Electrostatic discharge (ESD) can damage components of the module.

ESD, which occurs when the module is improperly handled, can cause

complete or intermittent failures.

CAUTION: To prevent ESD-related damage:

■Always wear an ESD wrist strap (not provided) when you handle a

module, ensuring that the strap makes good skin contact and is

properly grounded.

■Keep the module in its antistatic bag until you are ready to install it.

Handling Precautions When you handle the module, follow these precautions:

■Always handle the module by the front panel only.

■Do not touch the components, pins, leads, or solder connections.

■Do not twist or otherwise force the module into the chassis when you

insert it into the module guides.

■Before you push the module into the chassis, verify that the module

ejector handles are open.

■When you slide the module into the 7-slot chassis, match the left and

right module guides. In the 8-slot chassis or 16-slot chassis, match the

upper and lower module guides.

For details, see “Installation Prerequisites” and “Installing the Module”

later in this guide.

9-Port 1000BASE-SX Gigabit Ethernet Layer 2 Switching Module Quick Start Guide 5

Unpacking

Instructions

Use the following procedure when you unpack the module:

1Verify that the module is the correct model by matching the 3C number

that is listed on the shipping box label to the 3C number that you ordered

(Model Number 3CB9LG9MC).

2Remove the module, in its antistatic bag, from the shipping box.

3Observing the caution instructions, remove the module from its antistatic

bag and inspect it for physical damage.

CAUTION: Handle the module only by the front panel. Do not touch any

components, pins, leads, or solder connections.

If the module appears to be damaged, replace it in the antistatic bag, put

it back in the shipping box, and contact your network supplier.

4Verify that the box also contains:

■CoreBuilder 9000 Release Notes for the Fast Ethernet and Gigabit

Ethernet Layer 2 Switching Modules

■9-Port 1000BASE-SX Gigabit Ethernet Layer 2 Switching Module

Quick Start Guide for the CoreBuilder 9000 Enterprise Switch (this

guide)

If the listed contents are not in your shipping box, contact your network

supplier.

All shipping boxes are reusable. After you remove the contents, replace

the packing materials and store the shipping box for future use.

69-Port 1000BASE-SX Gigabit Ethernet Layer 2 Switching Module Quick Start Guide

Installation

Prerequisites

Before you install the 9-port GEN Layer 2 Switching Module, make the

following preparations:

■Verify that the chassis is properly installed in a rack, on a table, or on a

shelf, according to the instructions in either of these guides:

■7-Slot Chassis Quick Installation Guide for the CoreBuilder 9000

Enterprise Switch

■Chassis Quick Installation Guide for the CoreBuilder 9000

Enterprise Switch 8-slot Chassis and 16-slot Chassis.

■Have a flat-blade torque screwdriver available to secure the module to

the chassis after you install it.

■Read the CoreBuilder 9000 Release Notes for the Fast Ethernet and

Gigabit Ethernet Layer 2 Switching Modules for important information

about installing and upgrading modules in an existing chassis or a new

chassis.

CAUTION: All modules in a CoreBuilder 9000 chassis must operate at

compatible software levels. You must verify the software release on all

new and existing modules in your chassis and upgrade as necessary. See

the CoreBuilder 9000 Release Notes for the Fast Ethernet and Gigabit

Ethernet Layer 2 Switching Modules for a module software compatibility

requirements table, mandatory upgrade procedures, and other important

information.

Module Placement

in the Chassis

Note the following chassis slot restrictions and recommendations when

you choose a chassis slot for the 9-port GEN Layer 2 Switching Module:

■In the 7-slot chassis

■Do not install the module in slot 7. This slot is reserved for a GEN

Switch Fabric Module

■Install the module in slot 1, 2, 3, 4, 5, or 6.

■In the 8-slot chassis:

■Do not install the module in slot 7 or slot 8. These slots are

reserved for GEN Switch Fabric Modules.

■Install the module in slot 1, 2, 3, 4, 5, or 6.

9-Port 1000BASE-SX Gigabit Ethernet Layer 2 Switching Module Quick Start Guide 7

■In the 16-slot chassis:

■Do not install the module in slot 8 or slot 9. These slots are

reserved for GEN Switch Fabric Modules.

■To optimize backplane performance, install the module in slot 1, 2,

3, 4, 5, 6, 7, 10, 11, or 12.

■3Com recommends that you do not install the module in slot 13,

14, 15, or 16 because these slots have only one connection to the

backplane.

Table 1, Table 2, and Table 3 list the relationship between the following:

■24-port GEN Switch Fabric Module (SFM) (Model Number 3CB9FG24

or Model Number 3CB9FG24T)

■9-port GEN Layer 2 Switching Module

■Switching module slots in the 7-slot chassis, the 8-slot chassis, and the

16-slot chassis, respectively

Table 4 and Table 5 list the relationship between the following:

■9-port GEN Switch Fabric Module (SFM) (Model Number 3CB9FG9)

■9-port GEN Layer 2 Switching Module

■Switching module slots in the 7-slot chassis and the 8-slot chassis,

respectively

Use the table information to help you select a slot for your module, as

well as administer the system after you have completed the installation.

89-Port 1000BASE-SX Gigabit Ethernet Layer 2 Switching Module Quick Start Guide

Ta b l e 1 Mapping the 24-port GEN SFM and the 9-port GEN Switching Module to the 7-slot Chassis

Chassis Slot

Number

Number of SFM

Backplane Ports

Allocated to Slot

9-port Switching

Module Backplane

Port Numbers

SFM Backplane Port

Numbers Assigned

to Chassis Slot

SFM LED Numbers

Assigned to Backplane

Port Numbers

14; only 3 are accessed

by this module

24; only 3 are accessed

by this module

34; only 3 are accessed

by this module

44; only 3 are accessed

by this module

54; only 3 are accessed

by this module

21 (22 for Model

Number 3CB9FG24)

64; only 3 are accessed

by this module

23 (24 for Model

Number 3CB9FG24)

7Reserved for an SFM Not applicable Not applicable Not applicable

9-Port 1000BASE-SX Gigabit Ethernet Layer 2 Switching Module Quick Start Guide 9

Ta b l e 2 Mapping the 24-port GEN SFM and the 9-port GEN Switching Module to the 8-slot Chassis

Chassis Slot

Number

Number of SFM

Backplane Ports

Allocated to Slot

9-port Switching

Module Backplane

Port Numbers

SFM Backplane Port

Numbers Assigned

to Chassis Slot

SFM LED Numbers

Assigned to Backplane

Port Numbers

14; only 3 are accessed

by this module

24; only 3 are accessed

by this module

34; only 3 are accessed

by this module

44; only 3 are accessed

by this module

54; only 3 are accessed

by this module

21 (22 for Model

Number 3CB9FG24)

64; only 3 are accessed

by this module

23 (24 for Model

Number 3CB9FG24)

7Reserved for an SFM Not applicable Not applicable Not applicable

8Reserved for an SFM Not applicable Not applicable Not applicable

10 9-Port 1000BASE-SX Gigabit Ethernet Layer 2 Switching Module Quick Start Guide

Ta b l e 3 Mapping the 24-port GEN SFM and the 9-port GEN Switching Module to the 16-slot Chassis

Chassis Slot

Number

Number of SFM

Backplane Ports

Allocated to Slot

9-port Switching

Module Backplane

Port Numbers

SFM Backplane Port

Numbers Assigned

to Chassis Slot

SFM LED Numbers

Assigned to Backplane

Port Numbers

1 2 10

2 2 10

3 2 10

4 2 10

5 2 10

6 2 10

7 2 10

8Reserved for an SFM Not applicable Not applicable Not applicable

9Reserved for an SFM Not applicable Not applicable Not applicable

10 210

11 210

12 210

13 110 21 21

14 110 22 22

15 110 23 23

16 110 24 24

Tabla de contenidos

Otros manuales de Cambiar de 3Com

3Com

3Com NJ205 - IntelliJack Switch Hoja de especificaciones

3Com

3Com 3C16611 - SuperStack II Dual Speed Hub 500 Manual de usuario

3Com

3Com OfficeConnect WX1200 Manual de usuario

3Com

3Com SuperStack 4 3C16465B Manual de usuario

3Com

3Com 3C17709 Manual de usuario

3Com

3Com 5-10/100 Manual de usuario

3Com

3Com 5500-EI PWR Manual de usuario

3Com

3Com Switch 7754 Manual de usuario

3Com

3Com 3C16440 - SuperStack II Baseline Hub 12 Manual de usuario

3Com

3Com IntelliJack NJ2000 Manual de usuario

3Com

3Com Switch 4500 Family Manual de usuario

3Com

3Com 3C8S5007 - SuperStack II PathBuilder S500... Manual de usuario

3Com

3Com Gigabit Switch 8 Manual de usuario

3Com

3Com 4007 Manual de usuario

3Com

3Com SuperStack 3 3812 Manual de usuario

3Com

3Com LSBM1SRP1M1 Manual de usuario

3Com

3Com OfficeConnect 3C16790C Manual de usuario

3Com

3Com OfficeConnect WX4400 Manual de usuario

3Com

3Com 2928 - Baseline Plus Switch PWR Manual de usuario

3Com

3Com SuperStack II Switch 3300 FX Manual de usuario

3Com

3Com 5500-EI Series Manual de usuario

3Com

3Com SuperStack 3 3300 Manual de usuario

3Com

3Com CoreBuilder 6000 Manual de instrucciones

3Com

3Com S7906E - Switch Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario